ETA Systems PD9LV User manual

All designs and specifications are subject to change without notice. Copyright © 1997 ETA Systems.
October 1998
OWNER’S MANUAL
OPERATION INSTRUCTIONS
ETA’s line of Conditioned Power
Distribution
units are designed to
prevent electrical damage to sensitive
electronic equipment from high
amplitude/short duration spikes,
random surges, and EMI/RFI noise,
which is inherent in utility power lines.
Power line sources which are not
preconditioned or filtered can affect
reliable operation of sensitive audio,
computer, and other electronic
equipment, and may cause premature
failure, expensive repairs, or unan-
ticipated replacement from non-
repairable damage.
As inherent problems in utility AC
power lines increase for various
reasons, and the need for noise-free,
conditioned power increases, ETA is
there with the units to protect your
valuable electronic equipment. With
presentdemandsonthepowerutilities,
voltage spikes, power surges, electri-
cal noise, and power failures are
commonplace. This "garbage" in the
powerdeliveredcanreducethefidelity
of audio systems, cause premature
failure, or result in extensive damage
ordestructionofelectronic equipment.
ETA Conditioned Power Distribu-
tionunitsfeatureamasterpowerswitch,
convenientlylocatedonthefrontcontrol
panel, that switches the rear panel AC
outlets ON and OFF. An LED next to
the master power switch indicates the
power conditioning circuitry is working
and the rear panel AC outlets are
powered.Maximumtotalwattageinput
is 1800 watts and the 8 power output
receptacles, located on back panel
and one on front panel, are protected
with a 15-amp (total unit) resettable
circuit breaker.
Note: The front panel LED is
normallylitwhenthepowerswitchisin
the ON position. If the power switch is
ON and the LED is
not lit, power may
still be present on the output AC
receptacles,butthepowerconditioning
circuitryisnotworking.Donotcontinue
use of the power conditioning unit and
refer trouble-shooting to a qualified
electronic technician or contact ETA
Customer Service for assistance.
EASY INSTALLATION
ThePD9LandPD9LViseasilymounted
into a standard 19-inch rack or placed
into a free-standing position. With the
PD master power switch in the OFF
position, plug the line cord into a
convenient AC receptacle. Place the
unit’s power switch into the ON
position and check that the front panel
LED is lit. The lit LED indicates
conditioned and filtered AC power is
connected.Then,withtheirmasterpower
switches in the OFF position, plug the
equipment to be protected into the PD's
rear panel AC receptacles. Turn on the
powerswitchesoftheequipmentplugged
into the PD9L or PD9LV.
NOTE: The PD9L and PD9LV are
UL recognized and have a one-year
limited warranty.
BACK PANEL PD9L/PD9LV
TM®
SYSTEMS
A Creative Light & Sound Company
Division of National Biological Corporation
1532 Enterprise Parkway • Twinsburg, Ohio 44087
330-425-3388 • 800-321-6699 • Fax: [phone]
http://www.etasys.com E-mail [e-mail]
PD9L
PD9LV

®
SYSTEMS
A Creative Light & Sound Company
Division of National Biological Corporation
1532 Enterprise Parkway • Twinsburg, Ohio 44087
330-425-3388 • 800-321-6699 • Fax: [phone]
http://www.etasys.com E-mail [email protected]
™
All designs and specifications are subject to change without notice. Copyright © 1998 ETA Systems.
Thank you for considering and
purchasing an ETA Conditioned
Power Distribution unit.
By listening to our large base of
present and past customers, and
drawing upon many years of exper-
ience in design and solving high
amperage lighting and conditioned
power distribution needs, ETA has
developed an extensive line of
Audio Conditioned Power Distribu-
tionunitstoprotecta broad range of
sensitive electronic equipment.
ETA offers a complete line of
power conditioning units in addition
tothePD9LandthePD9LVmodels.
Theproductlineincludes12models
of professional Audio Conditioned
Power Distribution units that are UL
listed and include features such as
sequential power up/power down,
high amperage output, and AC
voltage regulator units.
SPECIFICATIONS:
Input Voltage 120V AC
Spike protected Line to neutral, neutral to ground,
line to ground
UL 1449 suppressed 395V
voltage rating
Response time <1NS Typical
Operating temp. range – 40°to +158°F
Maximum energy dissipation 450 joules (3 x 150)
Maximum surge current 12000A
Maximum surge voltage 6000V
Noise attenuation Transverse up to 20 dB
(1.5 kHz to 200 mHz)
INSTRUCTIONS TO REPLACE LIGHT TUBE LAMP (Reference diagrams above.)
1. Extend and hold light tubes, turn cap clockwise and pull to remove cap.
2. With light tube three quarters of full extension, insert index finger in light source hole at base of lamp, gently push bulb and
socket through the cap's hole and replace lamp.
3. Reset socket with white mark on top, opposite light source hole, gently force lamp and socket back into light tube to a firm
fit. (It may be necessary to joggle socket with one hand and guide with finger in light source hole to get proper placement.)
4. Hold light tube and snap cap back into place. Twist cap counter-clockwise firmly.
NOTE: Replacement lamp is a standard 120 volt, 4 watt incandescent lamp. (Christmas tree lamp)
1
2
3
4