Panasonic KX-UTG 300 User manual

Studio System 300
Basic Installation Guide
1
Panasonic Solutions Company

Table Of Contents
2
DESCRIPTION Page DESCRIPTION Page
Important Power OFF 3Block Diagram 25
Introduction 4GPI Menu 26
Base Station AG-BS300 5Battery Menu HPX370 and HPX500 27
CameraAdaptor AG-CA300 6Battery Menu HDX900 though HPX3700 28
Battery Mount 7GenLock Menu Settings 29
ROPAG-EC4 8SDI Switch and Menu settings 30
ROPAJ-RC10 9RTS Intercom Connections 31
View Finder InterfaceAG-YA500 10 Clear-Com Intercom Support 32
Studio Cable 300 11-12 HPX500 DA Setup 33-34
ROP Cable 10M 13 Fiber Option 35-36
ROP Cable 9” 14 Trouble Shooting 37-38
GenLock and SDI 15 Accessory Parts List 39
VF GPI/Return Cable 16 Cable Technical Reference 40-44
Lens Return Cable 17-18 AV-HS400ATally Connection 45
Lens Return with Tally Option 19 AV-HS450 Tally Connection 46
Tally Trigger Cable 20 Prompter Connection 47
Power Tap Mentor Power Cable 21 Replacement Parts 48
Power Tap Multi Adaptor 22 Support Hot Line 49
VF Cable 23 Notes 50
AJAPower Cable 24 .
Panasonic Solutions Company

IMPORTANT
POWER OFF
Please make sure the power is turned OFF
on all equipment before making any connections!
3
Panasonic Solutions Company

Section 1 -Studio System 300
Before installation of the Studio System 300, Lets review
all of the components and its function.
4
Introduction
Panasonic Solutions Company
The Studio System 300 will work with the following cameras:
AG-HPX300, AGHPX370, AGHPX500, AJ-HDX900,AJ-HPX2000,
AJ-HPX2700,AJ-HPX3000,AJ-HPX3100 andAJ-HPX3700.

Section 1 -Studio System 300
Base Station –AG-BS300
5
The Base Station AG-BS300 is the heart of the system.
It provides the following: Power to the Camera*, Tally, Intercom, GenLock,
Return Video (SDI or Video or Both) and ROP Control.
*Does not provide power under the following 3 conditions:
1. The Base Station is powered using 12 Volts DC.
2. A Fiber Option is used in place of the studio cable.
3. Using 2 RG6 Type BNC Cables Only (no power cable).
Front
Back
Panasonic Solutions Company

Section 1-Studio System 300
Camera Adaptor –AG-CA300
6
Back Right Left
The Camera Adaptor AG-CA300 attaches to the Anton Bauer Gold Mount
on the back of the Camera. It does the following:
Connects to the GenLock, SDI Out, ROP, Provides Intercom, Return
Video (SDI or Video or Both), GPI, Tally, Tally Out Trigger
and Power. It only needs 3 connections to connect with the Base Station
(1 Power and 2 SDI).
Panasonic Solutions Company

Section 1-Studio System 300
Battery Mount Option –Anton Bauer Gold Mount
7
If using a fiber option to run a cable length more than 100 M,
power must be provided locally at the camera head. The supplied
Anton Bauer Gold Battery Mount must be used. Do Not Try to power
the camera using the 4 Pin XLR 12V input. The system can only be
powered though the battery mount.
Panasonic Solutions Company

Section 1-Studio System 300
8
Remote Operation Panel (ROP) AG-EC4
The Remote Operation Panel (ROP) AG-EC4 is a simple control
panel that works with all system supported cameras.
This includes the following:HPX300, HPX370, HPX500, HDX900,
HPX2000, HPX2700, HPX3000, HPX3100 and HPX3700.
Front Back
Panasonic Solutions Company

Section 1-Studio System 300
9
Optional Remote Operation Panel AJ-RC10
Not Recommended for AG-HPX300, AG-HPX370 or AG-HPX500
The AJ-RC10 is a full featured
Remote Operation Panel.
It is recommended for the
Cameras that offer more
control options. Example:
Knee and Slope Controls,
Master Gama, Etc.
It is not recommended for
the HPX300, HPX370 or HPX500
as they are better suited to use the AG-EC4.
Cameras that can take advantage of the AJ-RC10:
HDX900, HPX2000, HPX2700, HPX3000, HPX3100 and HPX3700
Panasonic Solutions Company

Section 1-Studio System 300
10
View Finder Interface Box–AG-YA500
Not Available for AG-HPX300 or AG-HPX370
The AG-YA500 VF Interface Box
allows Return Video and Tally
to be sent to the View Finder.
This option is usually used when
the camera is in a hand held
configuration and or no on board
Monitor is present.
Panasonic Solutions Company