Etec MovingWash 7E User manual

Page | 1
MovingWash 7E
LED Beam Moving Head
Manual
This guide contains important information.
Please read before use .

Page | 2
1. INTRODUCTION
Thank you for choosing this LED Moving Head. With 7 x 10W
RGBW 4 in 1 LED, it produces extremely bright rays and unlimited
colors. Excellent for stage, club, bar, DJ, etc. To optimize the
performance of this product, please read this manual carefully
before use.
1.1 unzip
The following items are included in the carton:
■ 1 x Moving Beam 7E
■ 1 x Power cable
■ 1 x Holder
■ 1 x Operation manual
Carefully unpack the carton, check the contents to make sure that
all parts are in place and in good condition. Contact your supplier
immediately if a part is missing or damaged and store packaging
material for viewing.
1.2 Safety
Danger! Follow these important safety instructions to avoid
fire, electric shock or personal injury!
▪The product is intended for indoor use only.
▪Always switch off the power supply, disconnect the plug and
allow the device to cool down.
▪Make sure the device is properly grounded.
▪Please keep this manual for future reference.
Always make sure that you have the correct voltage and that the
existing mains voltage is not higher than indicated on the label or
rear panel of the device.

Page | 3
▪Always disconnect from the power before servicing or changing
the fuse.
▪Ensure that the power cable is never corrugated or damaged.
Attention!
Do not look directly at the LED light beam from a distance!
1.3 Features
▪LED Moving Head
▪DMX, Auto, sound activated, Master/Slave
▪12 DMX channels
▪Linearer Dimmer 0 –100%
▪Various Strobes 1-25 fps
▪Pan/Tilt: 540° / 255°
▪4- Grope LCD display
1.4 Product Overview
____|___ _________/ |________
Control panel Power In/Out DMX In/Out
2. CONFIGURATION
2.1 Assembly

Page | 4
The moving head is fully functional in any mounting position,
suspended, side mounted, or standing on a flat, level surface, etc.
IMPORTANT!!! If the unit is installed on ceilings or trusses,
always use safety cables. The safety cable must be capable of
holding 10 times the weight of the device.
2.3 AC Power
The device was designed for AC 100-240V 50-60Hz. All devices
must be operated directly from a circuit. This unit can not be
operated by Switchpackoder dimmer even if it is used exclusively
for a 0% to 100% switchover.
WARNING!!! All devices must be connected to circuits with
suitable grounding.
3. OPERATING INSTRUCTIONS
3.1 Menu overview
1
DMX
Address
DMX Address =
001
Change
with UP
and
DOWN
buttons
Confirm with ENTER
2R255
LEDs Red 0-255
Change
with UP
and
DOWN
buttons
Confirm with ENTER
3G255
LEDs Green 0-255
Change
with UP
and
DOWN
buttons
Confirm with ENTER
4B255
LEDs Blue 0-255
Change
Confirm with ENTER

Page | 5
with UP
and
DOWN
buttons
5H255
LEDs White 0-255
Ändern mit
UP und
DOWN
Tasten
Confirm with ENTER
6PR01
Automatic Program
(Pr01-Pr35)
Change
with UP
and
DOWN
buttons
Confirm with ENTER
7SP01
Speed control for
automatic programs
(SP01-Sp16)
Change
with UP
and
DOWN
buttons
Confirm with ENTER
8LD01
Color change mode
(LD01 -> fast /
LD02 -> slow)
Change
with UP
and
DOWN
buttons
Confirm with ENTER
9AUTO
Test Mode
Change
with UP
and
DOWN
buttons
Confirm with ENTER
Automatic
Change
with UP
and
DOWN
buttons
Confirm with ENTER
Sound control
Change
with UP
and
DOWN
buttons
Confirm with ENTER
10Reset
= ON / OFF
Change
with UP
and
DOWN
buttons
Confirm with ENTER

Page | 6
3.2 DMX channels
12 DMX channels
Channel
DMX value and functions
1 Pan
000-255Pan movement
2Tilt
000-255 Tilt movement
3P/T
Geschwindigkeit
000-255 Pan / Tilt speed from fast to slow
4Dimmer
000-255 Dimmer 0-100%
5Strobe
000-009 Strobe closed
010-250 strobe speed from slow to fast
251-255 Strobe open
6Red
000-255 Intensity ret 0-100%
7Green
000-255 Intensity green 0-100%
8Blue
000-255 Intensity blue 0-100%
9White
000-255 Intensity white 0-100%
10 color macros
000-016
R
136-152 RW
017-034
G
153-169 GW
035-050 B
170-186 BW
051-067
W
187-203 RBW
068-084
RG
204-220 RGW
085-101
GB
221-237 RGB
102-118
BW
238-255 RGBW
119-135
RB

Page | 7
11 Auto
Program
000-010 No function
011-120 Program 1
121-180 Program 2
181-245 Auto color change
246-255 Sound control
12 Speed
000-225 Color change speed control
4.General maintenance
4.1 Fuse Replacement
a. a. Unscrew the fuse holder and remove the damaged
fuse.
b. b. Replace with a fuse of exactly the same type and
screw the fuse holder back in place.
5. Specifications
Power consumption: 80W
Power supply: 100 - 240V
Voltage frequency: 50 / 60Hz
Number of Diodes: 7RGBW4in1
Diode Power: 10W
Display: LCD matrix
Dimmer: Linear: 0 - 100%
Number of DMX channels: 12DMX 512
Control interface: 4 buttons

Page | 8
Protection class: IP20
Housing: ABS
Measurements: 180x180x285mm
Weight: 2.6 kg
Importeur
Hansaring 138-142
48268 Greven
Fon: +49 (0) 25 71 - 80 5 40 42
Fax: [phone]
www.etec-professional.de