Eterna SSRCDMC User manual

Issue 2014
Model:
SSRCDMC / SSRCDWH - Single Fused RCD Spur
TWSRCDMC / TWSRCDWH - Twin Unswitched RCD Socket
These instructions are provided as a guideline to assist you.
PLEASE READ THESE INSTRUCTIONS BEFORE INSTALLATION
AND RETAIN FOR FUTURE REFERENCE
Pack contents:
1 x Fitting
2 x M3 screws
FOR PRODUCT ADVICE:
• T: 01933 673 144
• F: 01933 678 083
• E: [email protected].uk
Visit our website:
www.eterna-lighting.co.uk
INSTALLATION INSTRUCTIONS
A guide for qualied electricians
EVENTUALLY, YOU MAY WANT TO
REPLACE THIS PRODUCT:
Regulations require the recycling of Waste from
Electrical and Electronic Equipment (European
“WEEE Directive” eective August 2005—UK
WEEE Regulations eective 2nd January 2007).
Environment Agency Registered Producer: WEE/
GA0248QZ.
WHEN YOUR PRODUCT COMES TO THE END OF
ITS LIFE OR YOU CHOOSE TO REPLACE IT, PLEASE
RECYCLE IT WHERE FACILITIES EXIST  DO NOT
DISPOSE WITH HOUSEHOLD WASTE.
CLEANING:
Clean this tting only with a soft dry cloth.
Do not use any chemical or abrasive cleaners.
IF YOU EXPERIENCE PROBLEMS:
If you believe your product is defective, please return
it to the place where you bought it. Our Technical
Team will gladly advise on any Eterna Lighting
product, but may not be able to give specic
instructions regarding individual installations.
For breakage information visit:
www.eterna-lighting.co.uk
SSRCDMC
SSRCDWH
TWSRCDMC
TWSRCDWH

READ THIS FIRST:
Check the pack and make sure you have all of the
parts listed on the front of this booklet. If not,
contact the outlet where you bought this product.
This tting must be installed by a competent person
in accordance with the Building Regulations making
reference to the current edition of the IEE Wiring
Regulations (BS7671).
As the buyer, installer and/or user of this product
it is your own responsibility to ensure that this
spur or socket is t for the purpose for which you
have intended it. Eterna Lighting cannot accept
any liability for loss, damage or premature failure
resulting from inappropriate use.
Suitable for indoor use only.
Do not attach to surfaces which are damp, freshly
painted or otherwise electrically conductive (e.g.
metallic surfaces).
Make connections to the electrical supply in
accordance with the following code:
Live - Brown or Red
Neutral - Blue or Black
Earth - Green and Yellow
When making connections, ensure that the terminals
are tightened securely and that no strands of wire
protrude. Check that the terminals are tightened
onto the bared conductors and not onto any
insulation.
This product must be connected to Earth.
You are advised at every stage of your installation
to double-check all electrical connections you have
made. After you have completed your installation
there are electrical tests that should be carried out:
these tests are specied in the Wiring Regulations
(BS7671) referred to in the Building Regulations.
INSTALLATION:
SINGLE FUSED RCD SPUR
Connect the wiring from the mains supply to the
terminals marked “LINE”. See diagram opposite.
Connect the wiring from your appliance to the
terminals marked “LOAD”. See diagram opposite.
TWIN UNSWITCHED RCD SOCKET
Connect your mains supply wiring to the terminals
according to the colour code above. Note that
earth connections may be made to either or both
terminal(s) marked “E”. See diagram opposite.
OPERATION:
01. Restore the mains power (after installation).
02. Press the green reset button and check that the
indicator window has turned red.
03. (For every use) Press the TEST button.
04. Check that the indicator window has turned
white.
05. Press the reset button and use as a normal
socket.
SPECIFICATION:
• Maximum operating load: 13A resistive, 3A
inductive.
• Mechanically latched (no need to reset after power
loss).
• Responsive to both positive and negative cycles.
• Trip speed less than 40ms.
• 30mA trip current.
• RCD contact break: double pole.
NOTE: unit will trip if the live and neutral input is
reversed and if neutral and/or earth connections are
lost. The unit will also react to pulsating earth fault
currents.
N
E
NL
L
N
L
E
LOAD LINE
Brown (L)
Blue (N)
Yellow / Green (E)