EtherWAN EX35000 series User manual

Industrial Ethernet Switch
1
Quick Start Guide
This quick start guide describes how to install and use the
hardened Gigabit Ethernet Switch. Capable of operating at
temperature extremes of -20°C to +60°C, this is the switch of
choice for harsh environments constrained by space.
Physical Description
The Terminal Block and Power inputs
Power Input Assignment
Power3 12VDC DC Jack
＋9-32VDC
Power2 －Power Ground
＋9-32VDC
Power1 －Power Ground
Earth Ground
Terminal Block
Relay Alarm Assignment
FAULT
*Warning signal disable for following:
1. The relay contact closes if Power1 and
Power2 are both failed but Power3 on.
2. The relay contact closes if Power3 is failed
but Power1 and Power2 are both on.

Industrial Ethernet Switch
2
DC Terminal Block Power Inputs: There are two pairs of
power inputs can be used to power up this switch. Redundant
power supplies function is supported.
The 1000Base-T and 1000Base-SX/LX Connectors
1. The 1000Base-T Connections
The following lists the pinouts of 1000Base-T port.
2. The 1000Base-SX/LX Connections
The fiber port pinouts: The Tx (transmit) port of device I is
connected to the Rx (receive) port of device II, and the Rx
(receive) port of device I to the Tx (transmit) port of device II.
3. The WDM 1000Base-LX Connections
The fiber port pinouts: Only one single-mode optical fiber is
required to transmit and receive data.

Industrial Ethernet Switch
3
The Port Status LEDs
LED State Indication
10/100Base-TX
Steady A valid network connection established.
Link/ACT
(Green) Flashing Transmitting or receiving data.
ACT stands for ACTIVITY.
1000Base-T/SX/LX
Steady A valid network connection established.
Link/ACT
(Orange) Flashing Transmitting or receiving data.
ACT stands for ACTIVITY.

Industrial Ethernet Switch
4
Functional Description
yMeets IEC61000-6-2 EMC Generic Standard Immunity
for industrial environment.
ySupports
IEEE802.3/802.3u/802.3ab/802.3z/802.3x/802.1p.
Auto-negotiation: 10/100/1000Mbps, Full/Half-duplex;
Auto MDI/MDIX.
y1000Base-SX/LX: Multi mode, Single mode, or WDM
Single mode SC type.
yIEEE802.1p Queue Priority: Support 4 priority queues.
ySupports 8192 MAC addresses. Provides 1.125M bits
buffer memory.
ySupports jumbo frame up to 9K Bytes.
yAlarms for power failure by relay output.
yPower Supplies: Redundant 9-32VDC Terminal Block
power inputs and 9VDC DC JACK with 100-240VAC
external power supply. "For Use with Model UP0351
E-12P as power jack supply source".
yField Wiring Terminal: Use Copper Conductors Only,
14-24 AWG
yOperating voltage and Max. Current consumption: 0.6A
@ 12VDC, 0.3A @ 24VDC. Power consumption: 7.2W
Max.
yOperating temperature ranges from -20℃to 60℃.
ySupports DIN-Rail or Panel Mounting installation.

Industrial Ethernet Switch
5
Assembly, Startup, and Dismantling
yAssembly: Place the switch on the DIN rail from above
using the slot. Push the front of the switch toward the
mounting surface until it audibly snaps into place.
yStartup: Connect the supply voltage to start up the
switch via the terminal block (or DC JACK).
yDismantling: Pull out the lower edge and then remove
the switch from the DIN rail.

Industrial Ethernet Switch
6
Preface
A member of the growing family of rugged switches, this
switch addresses a need for a smaller switch. This switch
provides an affordable solution for rugged and outdoor
environment, transportation road-side cabinet, industrial
floor shop, multitenant dwellings or Fiber To The Home
(FTTH) applications. Capable of operating at temperature
extremes of -20°C to +60°C, this is the switch of choice for
harsh environments constrained by space.
Plug-and-Play Solution:
The switch is a plug-and-play Gigabit Ethernet Switch in
compact size. It doesn't have any complicated software to
set up.
This manual describes how to install and use the hardened
Gigabit Ethernet Switch. This switch integrates full wire
speed switching technology. This switch brings the answer
to complicated hardened networking environments.
To get the most out of this manual, you should have an
understanding of Ethernet networking concepts.
In this manual, you will find:
yFeatures on the switch
yIllustrative LED functions
yInstallation instructions
ySpecifications

Industrial Ethernet Switch
7
Table of Contents
QUICK START GUIDE 1
PHYSICAL DESCRIPTION 1
The Terminal Block and Power inputs 1
The 1000Base-T and 1000Base-SX/LX Connectors 2
The Port Status LEDs 3
FUNCTIONAL DESCRIPTION 4
ASSEMBLY,STARTUP,AND DISMANTLING 5
PREFACE 6
TABLE OF CONTENTS 7
PRODUCT OVERVIEW 8
HARDENED GIGABIT ETHERNET SWITCH 8
PACKAGE CONTENTS 8
PRODUCT HIGHLIGHTS 9
Basic Features 9
FRONT PANEL DISPLAY 10
PHYSICAL PORTS 11
INSTALLATION 12
SELECTING A SITE FOR THE SWITCH 12
DIN RAIL MOUNTING 13
CONNECTING TO POWER 14
12VDC DC Jack 14
Redundant DC Terminal Block Power Inputs 14
Alarms for Power Failure 15
CONNECTING TO YOUR NETWORK 16
Cable Type & Length 16
Cabling 17
SPECIFICATIONS 18
APPENDIX A–CONNECTOR PINOUTS 20

Industrial Ethernet Switch
8
Product Overview
Hardened Gigabit Ethernet Switch
Package Contents
When you unpack the product package, you shall find the
items listed below. Please inspect the contents, and report
any apparent damage or missing items immediately to your
authorized reseller.
3This Switch
3User’s Manual
3External power adapter & Power Cord
(Optional)

Industrial Ethernet Switch
9
Product Highlights
Basic Features
yMeets IEC61000-6-2 EMC Generic Standard Immunity
for industrial environment.
ySupports IEEE802.3/802.3u/802.3ab/802.3z/802.3x.
y1000Mbps-Full-duplex, 10/100Mbps-Full/Half-duplex.
yAuto-Negotiation, Auto MDI/MDIX.
y1000Base-SX/LX: Multi mode, Single mode, or WDM
Single mode SC type.
yIEEE802.1p Queue Supports 4 priority queues.
y8192 MAC addresses.
y1.125M bits buffer memory.
yFull wire-speed forwarding rate.
ySupports jumbo frame up to 9K Bytes.
yAlarms for power failure by relay output.
yPower Supplies: Redundant 9-32VDC Terminal Block
power inputs and 9VDC DC JACK with 100-240VAC
external power supply. "For Use with Model UP0351
E-12P as power jack supply source".
yField Wiring Terminal: Use Copper Conductors Only,
14-24 AWG
yOperating voltage and Max. current consumption: 0.6A
@ 12VDC, 0.3A @ 24VDC.
yPower consumption: 7.2W Max.
y-20℃to 60℃operating temperature.
yHardened aluminum case.
ySupports DIN-Rail or Panel Mounting installation.

Industrial Ethernet Switch
10
Front Panel Display
cPower Status (Power1, Power2, Power3)
These LEDs come on when the switch is properly connected to power and
turned on.
dPort Status LEDs
The LEDs display status for each respective port.

Industrial Ethernet Switch
11
LED State Indication
10/100Base-TX
Steady A valid network connection established.
Link/ACT
(Green) Flashing Transmitting or receiving data.
ACT stands for ACTIVITY.
1000Base-T/SX/LX
Steady A valid network connection established.
Link/ACT
(Orange) Flashing Transmitting or receiving data.
ACT stands for ACTIVITY.
Physical Ports
This switch provides:
•Eight 10/100/1000Base-TX ports
•Seven 10/100/1000Base-TX ports + one combo port
•Six 10/100/1000Base-TX ports + two combo ports
<Note> Combo port: Either 1000Base-SX/LX port or 10/100/1000Base-TX port.
CONNECTIVITY
•RJ-45 connectors
•SC connector on 1000Base-SX/LX fiber port

Industrial Ethernet Switch
12
Installation
This chapter gives step-by-step instructions about how to
install the switch:
Selecting a Site for the Switch
As with any electric device, you should place the switch
where it will not be subjected to extreme temperatures,
humidity, or electromagnetic interference. Specifically, the
site you select should meet the following requirements:
yThe ambient temperature should be between -20 to 60
degrees Celsius.
yThe relative humidity should be less than 95 percent,
non-condensing.
ySurrounding electrical devices should not exceed the
electromagnetic field (RFC) standards.
yMake sure that the switch receives adequate ventilation.
Do not block the ventilation holes on the switch
yThe power outlet should be within 1.8 meters of the
switch.

Industrial Ethernet Switch
13
DIN Rail Mounting
Fix the DIN rail attachment plate to the back panel of the
switch.
Installation: Place the switch on the DIN rail from above using
the slot. Push the front of the switch toward the mounting
surface until it audibly snaps into place.
Removal: Pull out the lower edge and then remove the switch
from the DIN rail.

Industrial Ethernet Switch
14
Connecting to Power
Redundant DC Terminal Block Power Inputs or 12VDC DC
Jack:
12VDC DC Jack
Step 1: Connect the supplied AC to DC power adapter to the receptacle on
the topside of the switch.
Step 2: Connect the power cord to the AC to DC power adapter and attach
the plug into a standard AC outlet with the appropriate AC voltage.
Redundant DC Terminal Block Power Inputs
There are two pairs of power inputs can be used to power
up this device. You only need to have one power input
connected to run the switch.
Step 1: Connect the DC power cord to the plug-able terminal block on the
switch, and then plug it into a standard DC outlet.
Step 2: Disconnect the power cord if you want to shut down the switch.

Industrial Ethernet Switch
15
Alarms for Power Failure
Step 1: There are two pins on the terminal block are used for power failure
detection. It provides the normally closed output when the power
source is active. Use this as a dry contact application to send a
signal for power failure detection.
Power Input Assignment
Power3 12VDC DC Jack
＋9-32VDC
Power2 －Power Ground
＋9-32VDC
Power1 －Power Ground
Earth Ground
Terminal Block
Relay Alarm Assignment
FAULT
*Warning signal disable for following:
1. The relay contact closes if Power1 and Power2 are
both failed but Power3 on.
2. The relay contact closes if Power3 is failed but
Power1 and Power2 are both on.
Special note:
The relay output is normal open position when there is no power to the
switch. Please do not connect any power source to this terminal to
prevent the shortage to your power supply.

Industrial Ethernet Switch
16
Connecting to Your Network
Cable Type & Length
It is necessary to follow the cable specifications below
when connecting the switch to your network. Use
appropriate cables that meet your speed and cabling
requirements.
Cable Specifications
Speed Connector Port Speed
Half/Full
Duplex
Cable Max.
Distance
10Base-T RJ-45 10/20 Mbps 2-pair
UTP/STP
Cat. 3, 4, 5
100 m
100Base-TX RJ-45 100/200 Mbps 2-pair
UTP/STP
Cat. 5
100 m
1000Base-T RJ-45 2000 Mbps 4-pair
UTP/STP
Cat. 5, 5e
100 m
1000Base-SX SC 2000 Mbps MMF (50 or
62.5µm)
550 m
1000Base-LX SC 2000 Mbps SMF (9 or
10µm)
10, 20, or 50
km

Industrial Ethernet Switch
17
Cabling
Step 1: First, ensure the power of the switch and end devices are turned off.
<Note> Always ensure that the power is off before any installation.
Step 2: Prepare cable with corresponding connectors for each type of port
in use.
<Note> To connect two regular RJ-45 ports between switches or hubs, you need a
straight or cross-over cable.
Step 3: Consult the previous section for cabling requirements based on
connectors and speed.
Step 4: Connect one end of the cable to the switch and the other end to a
desired device.
Step 5: Once the connections between two end devices are made
successfully, turn on the power and the switch is operational.

Industrial Ethernet Switch
18
Specifications
Hardened Gigabit
Ethernet Switch
10/100/1000Base-TX auto-negotiating ports
with RJ-45 connectors
1000Base-SX/LX fiber ports
Applicable
Standards
IEEE802.3 10Base-T
IEEE802.3u 100Base-TX
IEEE802.3ab 1000Base-T
IEEE802.3z 1000Base-SX/LX
Switching Method Store-and-Forward
Forwarding Rate
10Base-T:
100Base-TX:
1000Base-T:
1000Base-SX/LX:
10 / 20Mbps Half / Full-duplex
100 / 200Mbps Half / Full-duplex
2000Mbps Full-duplex
2000Mbps Full-duplex
Performance 148,80pps for 10Mbps
148,810pps for 100Mbps
1,488,100pps for 1000Mbps
Cable
10Base-T:
100Base-TX:
1000Base-T:
1000Base-SX/LX:
2-pair UTP/STP Cat. 3, 4, 5
2-pair UTP/STP Cat. 5
4-pair UTP/STP Cat. 5, 5e
Up to 100m (328ft)
MMF (50 or 62.5µm), SMF (9 or10µm)
LED Indicators Per unit –
Power status (Power1, Power2, Power3)
Per port –
10/100Base-TX - Link/ACT (Green)
1000Base-T/SX/LX - Link/ACT (Orange)
Dimensions 58mm (W) × 110mm (D) × 135mm (H)
(2.29” (W) × 4.33” (D) × 5.31” (H))
Net Weight 0.8Kg (1.76lbs.)
Power Terminal Block: 9-32VDC
DC Jack: 12VDC, External AC/DC required
Operating Voltage &
Max. Current
Consumption
0.6A @ 12VDC, 0.3A @ 24VDC
Power Consumption 7.2W Max.
Operating
Temperature
-20℃to 60℃(-4℉to 140℉)
Storage Temperature -40℃to 85℃(-40℉to 185℉)
Humidity 5%-95% non-condensing
Safety UL508, EN60950-1, IEC60950-1

Industrial Ethernet Switch
19
EMI FCC Part 15, Class A
EN61000-6-3:
EN55022, EN61000-3-2, EN61000-3-3
EMS EN61000-6-2:
EN61000-4-2 (ESD Standard)
EN61000-4-3 (Radiated RFI Standards)
EN61000-4-4 (Burst Standards)
EN61000-4-5 (Surge Standards)
EN61000-4-6 (Induced RFI Standards)
EN61000-4-8 (Magnetic Field Standards)
EN61000-4-11 (Voltage Dips Standards)
Environmental Test
Compliance
IEC60068-2-6 Fc (Vibration Resistance)
IEC60068-2-27 Ea (Shock)
IEC60068-2-32 Ed (Free Fall)

Industrial Ethernet Switch
20
Appendix A – Connector Pinouts
Pin arrangement of RJ-45 connectors:
RJ-45 Connector and Cable Pins
The following table lists the pinout of 10/100/1000Base-TX
ports.
Pin Ports
1 TP0＋
2 TP0－
3 TP1＋
4 TP2＋
5 TP2－
6 TP1－
7 TP3＋
8 TP3－