D-Link DVG-N5402G/ACF User manual

Quick Installation Guide
DVG-N5402G/ACF
Wireless AC1200 Dual Band Gigabit Router
ith Fiber WAN Port, 3G/LTE Support, 2 FXS
Ports, 1 PSTN (lifeline) Port, and USB Port

DVG-N5402G/ACF Quick Installation Guide
BEFO E YOU BEGIN
Delivery Package
•Router DVG-N5402G/ACF
•Power adapter DC 12V/2A
•Ethernet cab e (CAT 5E)
•Two RJ-11 te ephone cab es
•“Quick Installation Guide” (brochure).
If any of the items are missing, p ease contact your rese er.
The “User Manual” and “Quick Installation Guide” documents are avai ab e
on D-Link website (see www.d ink.ru).
!Using a power supply with a different voltage rating than the one
included will cause damage and void the warranty for this product.
2

DVG-N5402G/ACF Quick Installation Guide
Default Settings
IP address of wireless router 192.168.8.254
Username (login) admin
Password admin
Name of wireless network
(SSID)
2.4GHz DVG-N5402G
5GHz DVG-N5402G-5G
Network key (PSK)
see WPS PIN on the
barcode abe on the
bottom pane of the
device
!
Router DVG-N5402G/ACF with defau t settings cannot connect to the
Internet. To get started, p ease set your own password for access to the
web-based interface and change the WLAN name (SSID); then, if
needed, configure other settings recommended by your ISP.
3

DVG-N5402G/ACF Quick Installation Guide
System Requirements and Equipment
•A computer with any operating system that supports a web browser.
•A web browser to access the web-based interface of the router:
◦App e Safari 5 and ater
◦Goog e Chrome 10 and ater
◦Microsoft Internet Exp orer 9 and ater
◦Microsoft Edge 20.10240 and ater
◦Mozi a Firefox 10 and ater
◦Opera 10 and ater.
•A NIC (Ethernet or Wi-Fi adapter) to connect to the router.
•An 802.11a, b, g, n, or ac Wi-Fi adapter to create a wire ess network.
•SFP transceiver to connect to a fiber optic ine.
•Ana og phone.
•A USB modem (when it is necessary to connect to the Internet via mobi e
operators' networks)1.
!
Your USB modem shou d be equipped with an active identification
card (SIM or R-UIM) of your operator.
Some operators require subscribers to activate their USB modems prior
to using them. P ease, refer to connection guide ines provided by your
operator when conc uding the agreement or p aced on its website.
For LTE or CDMA USB modems, it is required to disab e the PIN code
check on the identification card prior to connecting the USB modem to
the router.
1 Contact your operator to get information on the service coverage and fees.
4

DVG-N5402G/ACF Quick Installation Guide
CONNECTING TO PC
PC with Ethernet Adapter
1. Make sure that your PC is powered off.
2. Connect an Ethernet cab e between any of LAN ports ocated on the back
pane of the router and the Ethernet port of your PC.
3. To connect via USB modem: connect your USB modem to the USB port2
ocated on the back pane of the router.
!If you need to connect or change a USB modem to another one when
the router is powered on, power off the router, connect the modem to
the USB port, and power on the router.
4. To connect the device to a fiber optic line: connect your SFP transceiver
to the SFP port, then connect the fiber optic cab e to the SFP transceiver.
5. To connect the device to an Ethernet line: in the web-based interface of
the router, se ect the router's LAN port that wi be used as the WAN port
and create an Ethernet WAN connection. Then connect an Ethernet cab e
between an avai ab e Ethernet port of the router and the Ethernet ine.
!P ease connect the router to the ISP's Ethernet ine on y after setting the
WAN port and creating the Internet connection.
6. Connect the power cord to the power connector port on the back pane of
the router, then p ug the power adapter into an e ectrica out et or power
strip.
7. Turn on the router by pressing the ON/OFF button on its back pane .
8. Turn on your PC and wait unti your operating system is comp ete y
oaded.
Now you shou d configure your PC to obtain an IP address automatica y (as
DHCP c ient).
2 It is recommended to use a USB extension cab e to connect a USB modem to the
router.
5

DVG-N5402G/ACF Quick Installation Guide
Obtaining P Address Automatically
in OS Windows XP
1. C ick the Start button and proceed to the Control Panel > Network
and Internet Connections > Network Connections window.
2. In the Network Connections window, right-c ick the re evant Local
Area Connection icon and se ect the Properties ine in the menu
disp ayed.
3. In the Local Area Connection Properties window, on the General
tab, se ect the Internet Protocol (TCP/IP) ine. C ick the Properties
button.
6

DVG-N5402G/ACF Quick Installation Guide
4. Se ect the Obtain an IP address automatically and Obtain DNS
server address automatically radio buttons. C ick the OK button.
5. C ick the ОК button in the connection properties window.
Now your computer is configured to obtain an IP address automatica y.
7

DVG-N5402G/ACF Quick Installation Guide
Obtaining P Address Automatically
in OS Windows 7
1. C ick the Start button and proceed to the Control Panel window.
2. Se ect the Network and Sharing Center section. (If the Contro Pane
has the category view (the Category va ue is se ected from the View by
drop-down ist in the top right corner of the window), choose the
View network status and tasks ine under the Network and
Internet section.)
3. In the menu ocated on the eft part of the window, se ect the Change
adapter settings ine.
4. In the opened window, right-c ick the re evant Local Area Connection
icon and se ect the Properties ine in the menu disp ayed.
5. In the Local Area Connection Properties window, on the
Networking tab, se ect the Internet Protocol Version 4 (TCP/IPv4)
ine. C ick the Properties button.
8

DVG-N5402G/ACF Quick Installation Guide
6. Se ect the Obtain an IP address automatically and Obtain DNS
server address automatically radio buttons. C ick the OK button.
7. C ick the OK button in the connection properties window.
Now your computer is configured to obtain an IP address automatica y.
9

DVG-N5402G/ACF Quick Installation Guide
PC with Wi-Fi Adapter
1. To connect via USB modem: connect your USB modem to the USB
port3 ocated on the back pane of the router.
!If you need to connect or change a USB modem to another one when
the router is powered on, power off the router, connect the modem to
the USB port, and power on the router.
2. To connect the device to a fiber optic line: connect your SFP
transceiver to the SFP port, then connect the fiber optic cab e to the
SFP transceiver.
3. To connect the device to an Ethernet line: in the web-based interface
of the router, se ect the router's LAN port that wi be used as the WAN
port and create an Ethernet WAN connection. Then connect an
Ethernet cab e between an avai ab e Ethernet port of the router and the
Ethernet ine.
!P ease connect the router to the ISP's Ethernet ine on y after setting the
WAN port and creating the Internet connection.
4. Connect the power cord to the power connector port on the back pane
of the router, then p ug the power adapter into an e ectrica out et or
power strip.
5. Turn on the router by pressing the ON/OFF button on its back pane .
6. Turn on your PC and wait unti your operating system is comp ete y
oaded.
7. Turn on your Wi-Fi adapter. As a ru e, modern notebooks with bui t-in
wire ess NICs are equipped with a button or switch that turns on/off
the wire ess adapter (refer to your PC documents). If your PC is
equipped with a p uggab e wire ess NIC, insta the software provided
with your Wi-Fi adapter.
Now you shou d configure your Wi-Fi adapter.
3 It is recommended to use a USB extension cab e to connect a USB modem to the
router.
10

DVG-N5402G/ACF Quick Installation Guide
Configuring Wi-Fi Adapter in OS Windows XP
1. C ick the Start button and proceed to the Control Panel > Network
and Internet Connections > Network Connections window.
2. Se ect the icon of the wire ess network connection and make sure that
your Wi-Fi adapter is on.
3. Search for avai ab e wire ess networks.
4. In the opened Wireless Network Connection window, se ect the
wire ess network DVG-N5402G (for operating in the 2.4GHz band) or
DVG-N5402G-5G (for operating in the 5GHz band) and c ick the
Connect button.
5. In the opened window, enter the network key (see WPS PIN on the
barcode abe on the bottom pane of the device) in the Network key and
Confirm network key fie ds and c ick the Connect button.
After that the Wireless Network Connection Status window appears.
!
If you perform initia configuration of the router via Wi-Fi connection,
note that immediate y after changing the wire ess defau t settings of the
router you wi need to reconfigure the wire ess connection using the
new y specified settings.
11

DVG-N5402G/ACF Quick Installation Guide
Configuring Wi-Fi Adapter in OS Windows 7
1. C ick the Start button and proceed to the Control Panel window.
2. Se ect the Network and Sharing Center section. (If the Contro Pane
has the category view (the Category va ue is se ected from the View by
drop-down ist in the top right corner of the window), choose the View
network status and tasks ine under the Network and Internet
section.)
3. In the menu ocated on the eft part of the window, se ect the Change
adapter settings ine.
4. In the opened window, se ect the icon of the wire ess network connection
and make sure that your Wi-Fi adapter is on.
5. To open the ist of avai ab e wire ess networks, se ect the icon of the
wire ess network connection and c ick the Connect To button or eft-
c ick the network icon in the notification area ocated on the right side of
the taskbar.
12

DVG-N5402G/ACF Quick Installation Guide
6. In the opened window, in the ist of avai ab e wire ess networks, wire ess
network DVG-N5402G (for operating in the 2.4GHz band) or DVG-
N5402G-5G (for operating in the 5GHz band) and c ick the Connect
button.
7. In the opened window, enter the network key (see WPS PIN on the
barcode abe on the bottom pane of the device) in the Security key
fie d and c ick the OK button.
8. Wait for about 20-30 seconds. After the connection is estab ished, the
network icon wi be disp ayed as the signa eve sca e.
!
If you perform initia configuration of the router via Wi-Fi connection,
note that immediate y after changing the wire ess defau t settings of the
router you wi need to reconfigure the wire ess connection using the
new y specified settings.
13

DVG-N5402G/ACF Quick Installation Guide
CONFIGU ING OUTE
Connecting to Web-based nterface
Start a web browser. In the address bar of the web browser, enter the IP
address of the router (by defau t, the fo owing IP address is specified:
192.168.8.254). Press the Enter key.
!
If the error “ The page cannot be displayed ” (or “ Unable to display the
page ”/“ Could not connect to remote server ”) occurs upon connecting to
the web-based interface of the router, make sure that you have proper y
connected the router to your computer.
After the first access to the web-based interface you need to change the defau t
administrator password. Enter the new password in the Password and
Confirmation fie ds. You may set any password except admin. Use digits,
Latin etters (uppercase and/or owercase), and characters avai ab e on the
keyboard. A so you need to change the defau t name of the wire ess network.
To do it, in the Network name (SSID) and 5GHz Network name (SSID)
fie ds, enter a new name for the router's wire ess network in the 2.4GHz and
5GHz band corresponding y or eave the va ues suggested by the router: DVG-
N5402G-XXXX and DVG-N5402G-5G-XXXX where XXXX are the ast 4
characters of the device's MAC address. Then c ick the Apply button.
14

DVG-N5402G/ACF Quick Installation Guide
!
Remember or write down the new password for the administrator
account. In case of osing the new password, you can access the settings
of the router on y after restoring the factory defau t settings via the
hardware RESET button. This procedure wipes out a settings that you
have configured for your router.
When the web-based interface is accessed the next time and after, the ogin
page opens. Enter the username (admin) in the Login fie d and the password
you specified in the Password fie d, then c ick the Enter button.
15

DVG-N5402G/ACF Quick Installation Guide
After successfu registration the Home / Information page opens. The page
disp ays genera information on the router and its software.
16

DVG-N5402G/ACF Quick Installation Guide
The web-based interface of the router is mu ti ingua . If you need to se ect
another anguage for the web-based interface, p ace the mouse pointer over the
English caption in the top part of the page and se ect a anguage from the
menu disp ayed.
To configure the router use the menu in the eft part of the page. Go to the
re evant section and se ect the needed page or run the needed Wizard in the
Home section.
A so you can find a specific page via search. To do this, enter the name of the
page, who y or part y, in the search bar in the top part of the web-based
interface page, and then se ect a needed ink in the search resu ts.
17

DVG-N5402G/ACF Quick Installation Guide
Configuring Connection to the nternet
!
You shou d configure your WAN connection in accordance with data
provided by your Internet service provider (ISP). Make sure that you
have obtained a necessary information prior to configuring your
connection. Otherwise contact your ISP.
LTE WAN Connection
If the PIN code check is enab ed for the SIM card inserted into your LTE USB
modem, it is required to disab e the PIN code check on the identification card
prior to connecting the USB modem to the router.4
An active LTE WAN connection wi be automatica y created on the Net /
WAN page when connecting a USB modem to the router. If the connection has
not been created automatica y, create a new connection manua y.
!For the USB modem Megafon M100-1, p ease reboot the router after
creating the WAN connection.
1. Go to the Net / WAN page and c ick the Add button.
2. In the General settings section, in the Provider drop-down ist, eave
the Manually va ue.
3. From the Connection Type drop-down ist, se ect the LTE va ue.
4. Make sure that the USB va ue is se ected from the Interface drop-down
ist.
5. Specify a name for your connection (any name for easier identification) in
the Name fie d.
4 Some mode s of LTE USB modems a ow disab ing the PIN code check in the web-
based interface of the router.
18

DVG-N5402G/ACF Quick Installation Guide
19

DVG-N5402G/ACF Quick Installation Guide
6. If your operator requires to specify the access point name, in the USB
modem section, fi in the APN fie d. If the operator has provided a
username ( ogin) and password, se ect the Set username and
password checkbox and fi in the corresponding fie ds.
7. If your operator has provided the address of the DNS server, in the IP
section, dese ect the Obtain DNS server addresses automatically
checkbox and fi in the Primary DNS server fie d.
8. C ick the Apply button.
9. On the Net / WAN page, se ect the choice of the Default gateway radio
button corresponding to the new LTE WAN connection.
20