EtherWAN EX49000 User manual

EX49000 HardenedWeb-SmartPoEEthernetSwitch www.etherwan.com
This quick start guide describes how to install and use the Hardened Web-Smart PoE (Power over
Ethernet) Ethernet Switch. Port and LED number will vary on different models. This user's manual will
only use EX49162 to cover all models.
Physical Description
The Port Status LEDs and Power Inputs
LED State Indication
Steady Power on.
Power1
Power2 Off Power off.
Steady Power redundant system failure occurred.
Fault Off Power redundant system failure is not occurred.
10/100Base-TX
Steady A valid network connection established.
Link/ACT Flashing Transmitting or receiving data.
ACT stands forACTIVITY.
Steady Valid port connection at 100Mbps.
10/100 Off Valid port connection at 10Mbps.
Steady Powered device (PD) is connected.
PoE Off Powered device (PD) is disconnected.
LED State Indication
Gigabit Ethernet
Steady A valid network connection established.
Link/ACT Flashing Transmitting or receiving data.
ACT stands forACTIVITY.
Steady A valid TX connection established.
TX Off No valid TX connection established.
Steady A valid SFP connection established.
SFP Off No valid SFP connection established.
DC Terminal Block Power Inputs: There are two pairs of power inputs can be used to power up this switch.
Redundant power supplies function is supported.
Power Input Assignment
＋47-57VDC
Power2 －Power Ground
＋47-57VDC
Power1 －Power Ground
Earth Ground
Terminal Block
Relay Output Rating 1A @ 24VDC
The 10/100Base-TX (PoE) and Gigabit Ethernet Connectors
The 10/100Base-TX (PoE) Connections
The following lists the pinouts of 10/100Base-TX ports.
Pin Signal Name Signal Definition
1 TD＋Output Transmit Data ＋
2 TD－Output Transmit Data －
3 RD＋Input Receive Data ＋
4 PoE Positive (VCC＋)
5 PoE Positive (VCC＋)
6 RD－Input Receive Data －
7 PoE Negative (VCC－)
8 PoE Negative (VCC－)
1
70G-EX49000Q1

EX49000 HardenedWeb-SmartPoEEthernetSwitch www.etherwan.com
2 70G-EX49000Q1
Login the switch:
Specify the default IP address (192.168.1.10) of the switch in the web browser. A login window will be
shown as below:
Enter the factory default user name: admin. Enter the factory default password: admin.
Then click on the “OK” button to log on to the switch.
Web Configuration
Meets NEMA TS2 Environmental requirements such as temperature, shock, and vibration for
traffic control equipment.
The 1000Base-T Connections
The following lists the pinouts of 1000Base-T ports.
Pin Signal Name Signal Definition
1 TP0＋Transmit and Receive Data 0 ＋
2 TP0－Transmit and Receive Data 0 －
3 TP1＋Transmit and Receive Data 1 ＋
4 TP2＋Transmit and Receive Data 2 ＋
5 TP2－Transmit and Receive Data 2 －
6 TP1－Transmit and Receive Data 1 －
7 TP3＋Transmit and Receive Data 3 ＋
8 TP3－Transmit and Receive Data 3 －
The SFP Socket Connections
The SFP socket for Gigabit fiber optic expansion.
The 1000Base-SX/LX Connections
The fiber port pinouts
The Tx (transmit) port of device I is connected to the Rx (receive) port of device II,
and the Rx (receive) port of device I to the Tx (transmit) port of device II.
The WDM 1000Base-BX Connections
The fiber port pinouts
Only one optical fiber is required to transmit and receive data.
Meets EN61000-6-2 & EN61000-6-4 EMC Generic Standard Immunity for industrial environment.
1000Mbps-Full-duplex, 10/100Mbps-Full/Half-duplex. Auto-Negotiation, Auto-MDI/MDIX.
Supports IEEE802.3at Power over Ethernet (PoE) Power Sourcing Equipment (PSE).
Device power consumption: 15W Max. (without PoE). PoE power budget: 480W Max.
Supports 4096 MAC addresses. Provides 2.25M bits memory buffer.
Power Supply: Redundant 55VDC Terminal Block power inputs.
Up to Max. 16 IEEE802.3at compliant PoE PSE (30W) ports.
-40 to 75 (℃℃-40℉to 167℉) operating temperature range.
Alarms for power and port link failure by relay output.
Manageable via Web browser interface.
Functional Description
Supports Rack Mounting installation.
2 Gigabit SFP combo ports.