Etlin-Daniels EE202WH-A13BB-GU User manual

SAVE THESE INSTRUCTIONS - READ ALL INSTRUCTIONS CAREFULLY
INSTALLATION MANUAL FOR EE202WH-A13BB-GU / LED RUNNING MAN EDGE LIT EXIT SIGN
IMPORTANT SAFEGUARDS
WIRING DIAGRAM
READ AND FOLLOW ALL SAFETY INSTRUCTIONS
• Review the diagrams thoroughly before beginning.
• All electrical connections must be in accordance with local codes,
ordinances and the National Electric Code.
• Disconnect power at fuse or circuit breaker before installing
or servicing.
• Do not use outdoors.
• Do not mount in hazardous locations or near gas or electric heaters.
• Do not let power cords touch hot surfaces.
• Equipment should be mounted in locations and at heights where
it will not be subject to tampering by unauthorized personnel.
• The use of accessory equipment is not recommended by
the manufacturer.
• Do not use this equipment other than intended use.
• All servicing should be performed by qualied personnel only.
• Allow battery to charge for 24hrs before rst use.
Head Oce - 1850 Wilson Ave. · Toronto, ON · M9M 1A1 · Tel: [phone] · Fax: [phone] ·
Toll Free: in Canada. 1.800.661.9610 · in USA. 1.888.762.5384 (SOCKETS4U)
www.etlin-daniels.com· For sales/service questions - [email protected]
Blac k Wire (L)
White Wire (N)
Transformer
For batter y
Batter y
Input AC cabl e
MAIN PCBA
Test
red le d
LED Stri p
SP
SP
• Emergency duration: ≥ 2 hours
• Recharge time: 24 hours
• Output Wattage: 1W
AC/SP WIRING
CIRCUITRY
Models / Input Voltage EE202WH-A13BB-GU
AC 120V
50 / 60 Hz
Input Wattage : 3W
Input Current : 0.24A
Eciency: 0.98P
AC 277V
50 / 60 Hz
Input Wattage : 3.5W
Input Current : 0.014A
Eciency: 0.93P
AC 347V
50 / 60 Hz
Input Wattage : 4W
Input Current : 0.017A
Eciency: 0.92P
PS: Battery voltage is negatively relative to input wattage
AC /SP WIRING
Black Wire (L)
AC120V -347V
Whit e Wire (N)
• Light Source: Ultra bright LED
• Color temperature: 6500K - 7500K
• Ni-cad Battery: 3.6V 800mAh jj
1. Attach spider plate / crossbar to junction box, use screws if needed.
2. Feed AC supply wire through canopy center hole.
3. Assemble canopy onto aluminum housing with screws (supplied) and make proper wire connections.
3.1 Black Wire (L); White Wire (N);
junction box
canopy
crossbar
traverse
4. Use screws (supplied) to tighten canopy to mounting plate (spider plate/cross bar)
5. The unit can be installed on any surface, you may rotate the Acrylic panel in any angle from
0 degrees to 180 degrees.
CEILING MOUNT
AC WIRING
Working Voltage:
AC120V - 347V 50Hz / 60Hz
Black Wire (L)
White Wire (N)
--------------------
Green Wire (E)

1. Attach spider plate / crossbar to junction box, use screws if needed.
2. Feed AC supply wire through canopy center hole.
3. Assemble canopy onto aluminum housing with screws (supplied) and make proper wire connections.
3.1 Black Wire (L); White Wire (N);
1. Attach spider plate / crossbar to junction box, use screws if needed.
2. Remove the opposite mounting end cap and knock out of the holes on the cap for pulling through
wires and assembly screws.
3. Pull out all AC supply wires and feed wires through the holes of end cap (rst) and then canopy.
SAVE THESE INSTRUCTIONS - READ ALL INSTRUCTIONS CAREFULLY
INSTALLATION MANUAL FOR EE202WH-A13BB-GU / LED RUNNING MAN EDGE LIT EXIT SIGN
Head Oce - 1850 Wilson Ave. · Toronto, ON · M9M 1A1 · Tel: [phone] · Fax: [phone] ·
Toll Free: in Canada. 1.800.661.9610 · in USA. 1.888.762.5384 (SOCKETS4U)
www.etlin-daniels.com· For sales/service questions - [email protected]
4. Use screws (supplied) to tighten canopy to mounting plate (spider plate/cross bar)
5. The unit can be installed on any surface, you may rotate the Acrylic panel in any angle from
0 degrees to 180 degrees.
1. Refer to assembly drawing before you start installation.
2. Position metal housing and bar hangers between joists. Make sure bar hangers are
oriented in the correct position.
junction box
junction box
crossbar
canopy
housing
end cap
opposite mounting end cap
canopy
housing
crossbar
traverse
SURFACE WALL MOUNT
WALL SIDE MOUNT
RECESSED MOUNT
4. Assemble canopy and end cap to metal bracket with screws (supplied) and make proper wire connections.
5. Using screws (supplied) tighten canopy to spider plate (crossbar).
6. The unit can be installed on any surface, you may rotate the Acrylic panel in any angle from
0 degree to 180 degree.
3. Adjust height of metal housing vertically using adjusting slots and tightening all scres on adjusting slots
and bar hanger bracket to secure adjusting bracket and bar hanger.
4. Make proper electrical connections at junction box in the ceiling.
5. Secure trim plate by using provided screws.

CHANGING OR REPLACING PICTOGRAM
SAVE THESE INSTRUCTIONS - READ ALL INSTRUCTIONS CAREFULLY
INSTALLATION MANUAL FOR EE202WH-A13BB-GU / LED RUNNING MAN EDGE LIT EXIT SIGN
Head Oce - 1850 Wilson Ave. · Toronto, ON · M9M 1A1 · Tel: [phone] · Fax: [phone] ·
Toll Free: in Canada. 1.800.661.9610 · in USA. 1.888.762.5384 (SOCKETS4U)
www.etlin-daniels.com· For sales/service questions - [email protected]
1. Unbolt the faceplate from the trim assembly.
2. Slide faceplate assembly out of the trim assembly.
3. Remove buttons.
4. Exchange pictogram.
5. Reinstall buttons press together
6. Slide face into the trim assembly and secure with nuts and bolts.
1. Insert the ber left side rst.
2. Insert ber right side second.
3. Insert on top and bottomsides third.
1. Select appropriate stencil and install stencil face into frame.
2. For single face option, place the back panel at back of the unit for optimum luminance.
Back Panel Back Panel
Button
Button Button
Button
Pictogram
Pictogram Pictogram
Pictogram
Acrylic with dots on both sides
Acrylic with dots on both sides
SINGLE FACE OPTION DOUBLE FACE OPTION