Euri ECR-55W103s User manual

WARNINGS WIRING DIAGRAM
• Do not use the electric generator to test the LED lamp.
• Please abide by related country, regional and local law and regulations when installing this fixture.
• Please turn off the power before installation or maintenance.
• Proper earth grounding is required to ensure safety.
WARNING/ AVERTISSEMENT
MIN 75°C SUPPLY CONDUCTOR
THIS PRODUCT MUST BE INSTALLED IN ACCORDANCE WITH THE APPLICABLE INSTALLATION CODE
BY A PERSON FAMILIAR WITH THE CONSTRUCTION AND OPERATION OF THE PRODUCT AND THE
HAZARDS INVOLVED.
IMPORTANT
• Please check if there is any damage during shipping. If so, please contact manufacturer immediately.
• Please read the installation instructions carefully to check whether all the accessories are
complete. After confirmation, install the fixture according to installation steps.
INSTALLATION (1)
INSTALLATION (2)
INSTALLATION GUIDE
MODEL #: ECR-55W103s / ECR-100W103s
©2020. Euri Lighting | A Division of IRTRONIX Inc. All Rights Reserved
For customer service please call us at 1-310-787-1100
Office Hours: 8:00 a.m. – 5:00 p.m. PST Monday-Friday
E-mail: [email protected]
Questions?

THIS PRODUCT MAY NOT BE COMPATIBLE WITH ALL DIMMERS, FOR MORE INFORMATION ABOUT DIMMER COMPATIBILITY PLEASE VISIT: WWW.EURILIGHTING.COM
LED Commercial Fixture
LED Parking Garage Lights
PLEASE REVIEW THE INSTRUCTIONS AND WARNINGS LISTED BELOW PRIOR TO PROPER INSTALLATION
LED Parking
Garage Light
1
1
2
23
3
4
4
7
56
Disassemble the
driver box cover.
Disassemble the
driver box cover.
Cling the safely
rope in the driver
box to the hook
inside the driver
box.
Lock the four
screws, the
product is
installed.
Connect the input
line and ground; If the
fixture is equipped with
sensor, adjust the sensor
settings; Take relevant
waterproof measures
after the wires are
connected.
Align the drive box
cover with the metal
shrapnel inside the
drive box and press
upward to fasten it
together.
Loosen the 3/4 plug on
the driver box cover by
screwdriver.
Loosen the 3/4 plug
on the driver box
cover by screwdriver.
Drill the holes on the
ceiling accordingly to
fit the plate.
Fix the driver box
cover on the 3/4
tube.
Cling the safety rope
in the driver box to
the hook inside the
driver box.
Fix the driver box
cover on the ceiling.
Lock the four screws,
the product is
installed.
Connect the input line and ground; lf the
fixture is equipped with sensors, adjust the
sensor settings, Take relevant waterproof
measures after the wires are connected.
Align the drive box cover with
the metal shrapnel inside the
drive box and press upward to
fasten it together.
5
8
67
please

LED Parking
Garage Light
INSTALLATION (3)
COLOR TEMPERATURE SWITCH
PARAMETER SETTING BY REMOTE CONTROL IN MANUAL OF RC-100 WIRING DIAGRAMS
- Move the switch left and
right to get the desired
color temperature.
- BRl823-B-D wiring with dimming ballast or LED
driver.
Dimming Driver
- BRl823-B-D wiring with non-dimming ballast or
LED driver.
Non-Dimming Driver
STRUCTURE OF MOTION SENSOR
RECOMMENDED DIMMER LIST
LUTON: NTSTV-DV / LEVITON: DS710-10Z / LEVITON: IP710 / Legrand: RH4FBL3PW
INSTALLATION GUIDE
MODEL #: ECR-55W103s / ECR-100W103s
©2020. Euri Lighting | A Division of IRTRONIX Inc. All Rights Reserved
For customer service please call us at 1-310-787-1100
Office Hours: 8:00 a.m. – 5:00 p.m. PST Monday-Friday
E-mail: [email protected]
Questions?

THIS PRODUCT MAY NOT BE COMPATIBLE WITH ALL DIMMERS, FOR MORE INFORMATION ABOUT DIMMER COMPATIBILITY PLEASE VISIT: WWW.EURILIGHTING.COM
LED Commercial Fixture
LED Parking Garage Lights
PLEASE REVIEW THE INSTRUCTIONS AND WARNINGS LISTED BELOW PRIOR TO PROPER INSTALLATION
1
5
2
67
8
9
10 11
34
Disassemble the
driver box cover.
Fix the lower
bracket on the
driver box cover.
Loosen the 3/4 plug on
the driver box cover by
screwdriver.
Align with the holes
of upper and lower
bracket; tighten with
screws.
Cling the safety rope
in the driver box to the
hook inside the driver
box.
Use M20 waterproof
connector when
connecting AC wire
or dimming wire, take
relevant waterproof
measures at both sides
of inlet.
Connect the input line and ground; If
the fixture is equipped with sensor,
adjust the sensor settings; Take
relevant waterproof measures after
the wires are connected.
Align the drive box cover with
the metal shrapnel inside the
drive box and press upward to
fasten it together.
Lock the four screws, the
product is installed.
Drill holes on the
ceiling.
Fix the upper
bracket on the
ceiling.