Eurolan TH100 User manual

IPTV SET TOP BOX
INSTRUCTION MANUAL
TH100
Technical Specifications
Interfaces:
Media content source:
Audio & Video:
LED indicators:
Power consumption
Power supply
Environment:
Dimensions:
Audio output S/PDIF, HDMI 1.4-output, Composite +
stereo A/V output, Ethernet 100 Mb/s, 2 x USB 2.0, WiFi (optional)
Local network PC or NAS, Stream media protocols (RTSP, RTP,
UDP, IGMP, HTTP), USB-device
Video modes: 1080i, 1080p, 720p, 576p, 480р, PAL, NTSC
Video codecs: MPEG1/2, H.265, H.264, MPEG4 part 2, XviD; HD
video supporting Audio codecs: MPEG-1 layer I/II, MPEG-2 layer II,
MPEG-2 layer III (mp3)
Power; Remote Activity; LAN Link/Activity
2,5 Watts (Max), 200mA/12V
External power adapter DC 12V
Operating Temperature: 10°C~30°C
Operating Humidity : 10%~80% (Non-Condensing)
130mm(L) x 88mm(W) x 28mm(H)
Connecting the TH100
Connecting to TV-SET with HDMI connector
Connecting to TV-SET with 3,5mm AV connector
Connecting to audio system with SPDIF connector

Programmable Remote Control Unit
TH100 package includes a remote control with a group of five
programmable buttons, marked with blue color which may be
used to control other devices.
To program the buttons:
Press and hold the blue “On/Off” and the “A/V” buttons at the
same time until you notice the red light of he blue “On/Off”
button becomes brighter. This means the remote is ready to
learn.
1. Choose the button you want to “teach” a new code to - the
red light of the “On/Off” button will start to blink.
2. Place the infrared outputs of the two remotes against each
other and press the button on the remote control of the
other device that you wish to copy and hold for 2 seconds.
3. You sill see the blue “On/Off button blink a couple of times
quickly, this means the button has been programmed.
4. Repeat steps 1 to 3 to choose and program the other
buttons of the remote control
5. Press and hold the blue “On/Off” and the “A/V” buttons at
the same time until you notice the red light of he blue
“On/Off” button turns off to save the programmed data.
USING THE REMOTE CONTROL UNIT
The remote control included into the package needs two AAA
batteries (also included into the package*) to operate.
Inserting the batteries
Remove battery Insert two AAA Replace the
cover batteries battery cover
IR receiver LED Indicator: Stand by mode,
Remote control button press
4-pin 3,5mm jack
AV output Ethernet
IR receiverIR receiverIR receiver
HDMI 2x USB SPIDF Power
Front panel
Rear panel
P a c k a g e C o n t e n t s :
IPTV Set top box -1pcs
External Power Supply -1pcs
IR Remote control -1pcs
AAA batteries -2pcs
Instruction manual -1pcs
HMDI cable -1pcs
Setting up the unit
1. Plug in the HDMI cable - if not HDMI cable is detected the AV output will be used
2. Plug in the power (IMPORTANT !! Do not plug in the network)
3. Wait until you see a message of NO CONNECTION
4. Press the setup button on the remote control -
5. Plug in the network cable
6. Press the Keyboard on the remote control to see the onscreen keyboard
7. Input the portal and network settings
8. If needed - change the name of the device it will report to the portal
9. Press F2 of the remote control
10. Press F4 of the remote control