Euronics EW01 User manual

EW01
Sensor Toilet Flusher
User Manual & Instruction

INSTALLATION INSTRUCTIONS
INSTRUCTIONS
**Default sensor distance: 900mm for human body
**Sensor range: 800-900mm for human body
**Flushing time range: 1-24s
**24 hours flush----set by remote controller
PRODUCT FEATURE
1)
)
Low power consumption: (Operation Consumption is <60uA and Overall
Power Consumption is <0.5W. 6V
2 Water saving and hygiene. The unit will automatically activate water flush after
usage. No touch design to keep hygiene.
3) Adjustable sensing range and flush duration.
BEFORE INSTALLATION
1) Please read the instructions carefully
2) The sketch map is only for reference. Product appearance and accessories may
differ from illustrations in manual.
3) Although the installation is simple, it should be done by a licensed plumber.
4) The following are needed for proper installations:wrench,screwdriver, sealing
tape,pliers, etc.

PRODUCT SPECIFICATIONS
Automatic Toliet Flush
AC220V
<60uA
<180mA
55-90cm (adjustable)
0.1-0.7 Mpa
DN25 (G1")
6-9L/flush time (0.3Mpa)
Concealled into the wall
110*160mm
130*130mm
Product Name
Power Supply
Operation Consumption
Dynamic Power Consumption
Sensing Distance
Water Pressure
Water Inlet Specification
Water Flow
Installation Way
Embedded Box Size
Faceplate size
INSTALLATION
1) Put the embedded box into the wall (water outlet downwards). Connect pipes
with the solenoid valve inlet and outlet respectively and fix it. Make sure the
outlet and toilet are kept in the same center line.
2) Connect power wire and sensor wire.
3) Use wood brick to level up the solenoid valve and test water pipe to make sure
there’s no leakage.
4) Move away the protection cover from the embedded box. Connect power wire
and solenoid wire and fix the faceplate into the embedded box.
160
180
80
Inlet
Outlet
Embedded dimension
110
130
170
Block
Block

Power Connector
Power Connector
Wire for
Solenoid Valve
AC 220V Input
Center Line
Block
Inlet
Outlet
eC ramic T li e
105
130
31 0
All measurements are in mm.

MAINTAINENCE INSTRUCTION
1) Water-flow regulating
Please use screwdriver to regulate water flow. Clockwise direction is to turn down
water flow while counter-clockwise direction is to turn up water flow.
2) Filter net cleaning
Please use screwdriver to back-out the filter net. Clean the filter net with clear
water and then fix it back.
Note: Please turn off the water regulating valve before you back-out the filter net.
noitalugerretaW
retliF
Fixed the panel back to original
location after adjustment.
NOTE
1. Please use damp towel or cotton cloth to wipe gently.
2. Please avoid any rocking or violent motion.
3. Please DO NOT use acid/alkaline detergents for cleaning.
Acid
Alkaline

SERVICEPARTSPAGE
Rubber diaphragm
Valve main body
Valve coil head
Valve core
Solenoid valve components exploded view
Cover
Valve cover
Valve piston
AC Power unit
Fixed plate
Solenoid Valve Assy
Sensor Assy
INSTALLATION SCHEME
Wall
Floor
Embedded
Box

Wall
Floor
Seat Surface
Embedded
Box
H< 54 0
Inlet/Out
Pipe G1
All measurements are in mm.

TROUBLE SHOOTING
*WARRANTY
Suggested Solution
Adjust sensing distance
Please make sure there’s
powr supply
Please check power supply and
replace power adapter
Replace sensor
Please connect solenoid
Please turn on water regulating valve
or water supply
Clean the filter net
Replace solenoid
Replace sensor
Clean the solenoid
Regulate water pressure to 0.1-0.7
Mpa
Regulate water flow
Clean the filter net
Regulate water pressure to 0.1-0.7
Mpa
Possible Reason
Sensing distance is too short
No power supply
Power adapter burn-up
Sensor broken
Check solenoid connection
Check water regulating valve
or water supply
Filter net block-up
Solenoid broken
Sensor broken
Solenoid block-up
Water pressure is too high or too
low
Check water regulating valve
Filter net block-up
Water pressure is too low
Problem
Indicator light
doesn’t light up
& no flush
Indicator light
lights up but no flush
Have a continuous
water flow problem
Low water flow
1 Year warranty on complete unit.
(Cleaning of filters is not covered under warranty).