EUROSTER 1310 User manual

EUROSTER 1310/E/P – USER MANUAL 1
EUROSTER 1310/E/P
PREPARATION: Before installing t is t ermostat, c eck your system wiring diagram.
If your system is ot er than a low voltage heating or cooling system, please check with your
local dealer. Do not connect both a Heat System and a Cool System to this thermostat.
NOT : Leave this Manual with the homeowner for future reference.
1. Look for a location that has a constant temperature in the house and is not near the
door entry or air conditioning outlet (see example on figure 1). Avoid sunny locations if
possible.
2. WARNING!!! Turn off the main power switch before installing the thermostat.
3. Release the front cover by pressing a tab on the top of the front cover with a
screwdriver (see figure 2). Remove the front cover with your hand holding both sides of
the cover (see figure 3).
4. Remove t e cover to get access to t e terminals (pus a small flat screwdriver
into t e gap from t e front and push the tab toward the center to open the cover).
Pull the cover straight up (see figure 4).
5. Route the wires through the cutout in the base and mount the thermostat to the wall
with two screws (see figure 5)."

EUROSTER 1310/E/P – USER MANUAL 2
Shove screw driver into gap and push toward
center to open plastic protection cover
CONTACT RATING : 8A 250 V
FIG.4
6. Install the wires into the terminal block and tighten the screws (see figure 6).
Wiring Diagram (see FIG. 6) UROST R 1310 FOR BATT RI S OP RAT D
MOD L
CONTACT RATING : 8A 250V
FIG. 6
Note
Terminal (1) N.O. contacts for Heating
Terminal (3) N.C. Contacts for Cooling
Terminal (5) C= Comon (one wire must be connected here)
7. Replace the terminal cover. Replace the front cover onto the base and make sure that
the hooks on the base are locked with the front cover.
8. Install the two batteries

EUROSTER 1310/E/P – USER MANUAL 3
9. Turn on the main power switch for operation
Key Function:
Setting & Operating
1. Press either  or  and LCD display will show a flashing temperature with „Heat On”
symbol ( ) and „Temperatury Set” symbol ().
2. Press again either  or  to set a desired temperature. very press on  will increase
1°C and every press on  will decrease 1°C.
3. When you complete setting your desired temperature, please wait for 15 seconds until
the LCD display stops flashing. Then, the termostat starts to operate and the LCD
display on the front panel of this unit shows room temperature with „Heat On” symbol
( ) until the temperature and then the unit will in operate to maintain the preset
temperature.
4. Thermostat shows actual ambient temperature and destination temperature, in
4 seconds periods.
5. When <ogienek> symbol is shown continuously, controlled heating appliance is on.
When it flickers, heating is off.
Setting a ysteresis
Thermostat can operate with hysteresis equal to 0,5, 1,0, 1,5 or 2,0 Celsius degrees.
To choose hysteresis, press and hold both ^ and v buttons for at least 10 seconds. Using ^
and v, select required hysteresis. Thermostat continues its normal operation after 5 seconds.
Batteries (E1310 only)
When batteries are low, <bat> symbol appears on LCD. In that case, replace batteries. Use
AAA size.
Power loss (E1310E/P)
Since 1310 /P don't have internal power source, you have to set required temperature again
when power failure occurs.
Tec nical data (E1310 only)
Measuring temperature range -30 °C … 60 °C
Measuring temperature resolution 0,1 °C
Controlling temperature range 5 °C … 35 °C
Hysteresis 0,5/1,0/1,5/2,0 °C, user-selectable
Display LCD
Supply 2 batteries, AAA size
Frequency of temperature measuring 1 minute
Maximum output current 7 A
Dimensions 73x28x73 mm

EUROSTER 1310/E/P – USER MANUAL 4
Tec nical data (E1310E/P)
Measuring temperature range -30 °C … 60 °C
Measuring temperature resolution 0,1 °C
Controlling temperature range 5 °C … 35 °C
Hysteresis 0,5/1,0/1,5/2,0 °C, user-selectable
Display LCD
Supply 230 V AC, 50 Hz
Current consumption 23 mA
Frequency of temperature measuring 1 minute
Maximum output current 10 A
Dimensions 73x28x73 mm