EUROSTER 3202 User manual

EUROSTER 3202 –USER MANUAL 1
EUROSTER 3202
Touch Screen Programmable Digital Thermostat
Thank you for choosing our Euroster 3202. This quality product has been tested strictly.
Before using your thermostat, please read the following instructions carefully.
FUNCTION
1. Manual mode
2. Auto mode (WAKE, LEAVE, RETURN and SLEEP)
3. 24-hour working mode
4. Accumulative heating time query
5. Programmable working mode
6. Permanent closing heating
7. LCD back-light
8. Touch screen function
OUTSIDE VIEW OF THE CONTROLLER
Key description:
is used to choose the mode and to confirm a choice. To exit the setting mode hold the
key over two seconds; 
increase value in setting mode;

EUROSTER 3202 –USER MANUAL 2
decrease value in setting mode.
WORKING/SETTING MODE
(1) Press key to enter the setting mode.
(2) Press / key to choose the setting mode (the one chosen will flicker).
the manual mode -> the time setting mode -> Auto mode.
To exit the setting mode hold the key over two seconds.
HOLD SETTING
1. Press to enter the setting mode.
2. Press / key to choose the manual mode setting, will flicker.
3. When pressing key again, temperature and time will flicker.
4. The initial time value displays: H:00-–denote duration manually hold temperature,
max: 99 hours, the min: 01 hour.
5. Set with / temperature/time.
6. Press to confirm, and to return to the working mode.
7. During the manual mode, pressing key will switch HOLD/Auto mode.
TIME SETTING
1. Press to enter the setting mode.
2. Press / to choose the time setting mode, will flicker.
3. Press to select the week day setting, week day will flicker.
4. Press / key to choose the day 1->2->3->4->5->6->7 (1 - monday).
5. Press key to confirm the current day, HOUR will flicker. Adjust with / key the
hour value.
6. Press key to confirm the current hour value, MINUTE will flicker. Adjust with /
key the MINUTE value.
7. Press key to confirm the current minute value. It will switch at the same time to the
working mode.

EUROSTER 3202 –USER MANUAL 3
AUTO MODE SETTING
1. Press to enter the setting mode.
1. Press / to choose the auto mode setting, will flicker.
2. Choose a day group. Press the / key to pick a week mode, there are 1 2 3 4 5, 1
2 3 4 5 6, 1 2 3 4 5 6 7 three modes, the group selected will flicker synchronously.
3. Press to confirm the day group, and the SUN will flicker. Pressing / key can
display the other second, third, fourth time point. It is possible to set the different time
points. When you pickup one time point, the relevant sign will flicker. When you press
the key again, it will enter the temperature setting, the temperature icon will flicker.
4. Press / to adjust temperature setting. Press to confirm temperature and enter
the first time point hour setting.
5. Press / to adjust hour setting. Press to confirm the hour value and enter the
first time point minute setting.
6. Press to confirm the minute value and enter the second time point setting, LEAVE
will flicker. Repeat the same time point and temperature setting, as described over.
To exit the setting mode hold the key over two seconds
6. Example of a factory program for a period from Monday to Friday

EUROSTER 3202 –USER MANUAL 4
PERMANENT STOP OF HEATING FUNCTION
In working mode press to switch off permanently heating. The heating icon will disappear.
Press again to come back to working mode.
ACCUMULATIVE HEATING TIME DISPLAY
Press / simultaneously, and accumulative heating time will be displayed: H0 00. Max.
accumulative time is 999 hours plus 59 min.
RESET FUNCTION
Press [RESET] while all icons display and set parameter can return to default. (Accumulative
heating time is not changing).
LED INDICATION
LED is bright when switch is on, and LED puts out when switch is off.
MEMORY FUNCTION
The thermostat has a memory function for user’s settings in case of black-out or power failure
(approximately for a week). However this function is limited by the capacity of an additional
internal battery.
THERMOSTAT INSTALLATION
ATTENTION Voltages hazardous to life may be present inside the thermostat and on its
output cables, therefore it is absolutely forbidden to install the device prior to disconnecting its
mains power supply. Only qualified technicians may install the thermostat. Do not install any
thermostats showing signs of mechanical damage.
Mount the thermostat in a place where ambient temperature does not exceed 40 °C. Lead all
necessary cables prior to mounting the thermostat. The thermostat is intended for installation
in a Ø60 flush mount back box.
Screw the cables to the connection blocks according to the description and drawing. Make sure
to keep the proper designation of the cables. Screw the neutral cable to N terminal, phase
cable to L terminal and grounding cable to PE terminal.
Screw the temperature sensor to the SENSOR block. The sensor may be connected in any way,
it has no polarity. During installation avoid leading the sensor parallel to power cables.
Moreover, make sure to place the sensor in proper contact with measured surfaces.
ATTENTION The temperature sensor is not suitable to be immersed in liquids.

EUROSTER 3202 –USER MANUAL 5
SAMPLE CONNECTION DIAGRAM
ELECTRONIC WASTE MANAGEMENT INFORMATION
We made every effort to get as a long controller lifetime as possible.
However, the device is subject to natural tear and wear. We ask you to
have a controller that will not meet your requirements any more brought in
to an electronic waste management facility. Electronic waste is collected
free of charge by local distributors of electronic equipment.
Inappropriate management of electronic waste may lead to an unnecessary
environment pollution.
Cardboard boxes should be disposed of at a paper recycling facility.

EUROSTER 3202 –USER MANUAL 6
GUARANTEE CERTIFICATE
EUROSTER 3202
Warranty terms:
1. Warranty is valid for 24 months from the controller sale date.
2. Claimed controller together with this warranty certificate must be supplied to the seller.
3. Warranty claims shall be processed within 14 business days from the date the
manufacturer has received the claimed device.
4. Controller may be repaired exclusively by the manufacturer or by other party clearly
authorized by the manufacturer.
5. Warranty becomes invalidated in case of any mechanical damage, incorrect operation
and/or making any repairs by unauthorized persons.
6. This consumer warranty does not exclude, restrict nor suspend any right of the Buyer
ensuing if the product would not meet any of the sale contract terms.
…..................................................................................................................................
sale date serial number/date of manufacture signature/stamp
Business entity that issued this warranty certificate:
P.H.P.U. AS Agnieszka Szymańska-Kaczyńska, Chumiętki 4, 63-840 Krobia, Poland