Honeywell UtilityPRO Series User manual

Operating Manual
UtilityPROTM Series
Touchscreen Programmable Demand Control Thermostat
85-3126

Read and save these instructions.
Need Help?
For assistance or warranty information please call your local Utility at the number found on the
front of the thermostat.
® U.S. Registered Trademark.
US Patents pending.
Copyright © 2007 Honeywell International Inc. All rights reserved.
BE CAREFUL! Never use sharp instruments, such as a pencil
or pen, to press touchscreen keys. To prevent damage to the
thermostat, always press keys with your fingertip.
This thermostat contains a Lithium battery which may contain
Perchlorate material.
Perchlorate Material—special handling may apply,
See www.dtsc.ca.gov/hazardouswaste/perchlorate

Battery Replacement
The UtilityPRO is shipped from the factory with the coin cell installed. To keep the
battery from discharging during shipment and storage, the UtilityPRO is shipped
from the factory with a plastic tab inserted in the battery holder. This tab must be
removed before the thermostat is mounted on the wall. Simply pull the plastic tab
out of the thermostat. To replace the battery, remove the battery tray using a screw
driver. Place a new coin cell (type CR2032 or equivalent) observing the correct
polarity and push the battery tray into the battery cover assembly.
The UtilityPRO has a coin cell
battery that retains the time
and date during a power failure.
Under normal circumstances the
coin cell should last five years.
Should the time and date need
to be reset after a power failure,
this is an indication that the coin
cell needs to be replaced. You
should replace battery every five
years, or before leaving home for
an extended period.
Coin cell
battery tray
Battery Cover
Assembly
Insert the coin cell battery in the coin cell battery
tray and push it inside the battery cover assembly

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC
Rules. Operation is subject to the following two conditions:
1) This device may not cause harmful interference.
2) This device must accept any interference received, including interference that may cause undesired operation.
Class B limits are designed to provide reasonable protection against harmful interference in a residential installation. This
equipment generates, uses, and can radiate radio frequency energy, and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However, there is not guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the
following measures:
• Reorient the receiving antenna.
• Increase the distance between the equipment and the receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the installer or an experienced radio/TV technician for help.
Industry Canada Requirements
Operation of this device is subject to the following two conditions:
1) This device may not cause interference.
2) This device must accept any interference, including interference that may cause undesired operation of the device.
FCC Part 15 Notice

1
About your new thermostat
Thermostat Features.................................. 2
Getting Started
Quick Reference to Controls ..................... 3
Quick Reference to Status Display........... 4
Subscription Services
Demand Control......................................... 5
Utility Usages ............................................. 6
Utility Messages......................................... 6
View Message ............................................ 7
Usage & Billing........................................... 8
Settings
Fan Settings ............................................... 9
System Settings ....................................... 10
Schedule Settings.................................... 11
Program Schedule Override (Temp)........ 12
Schedule Override (Permanent) ..............13
Clock Settings.......................................... 14
Programming & Operation
Program Schedules ............................15-16
Special Features ...................................... 17
Screen Lock ............................................. 18
Screen Cleaning....................................... 19
Advanced Functions...........................20-23
Troubleshooting ..................................24-25
This thermostat is ready to go!
Your new thermostat is pre-
programmed and ready to go.
See page 15 to check settings.
Table of contents
CAUTION: EQUIPMENT DAMAGE
HAZARD. To prevent possible
compressor damage, do not
operate cooling system when
outdoor
temperature is below 50F (10C).
UtilityPROTM Series

Operating Manual
2
UtilityProTM Features
Congratulations! You’ve just purchased the world’s most advanced, easy-to-use
thermostat. It has been designed to give you many years of reliable service and
touchscreen climate control.
Features
• Provides Utility information messages.
• Provides Utility billing information.
• 5/1/1 and 5/2-day program schedules maximize comfort and economy.
• Demand response thermostat programmed to aid you in your savings.
• EnergyStar®compliant to greatly reduce your heating/cooling expenses.
• One-touch temp control overrides program schedule at any time.
• Precise comfort control keeps temperature within 1°F of the level you set.
• Provides demand control messages.
• Large touchscreen display with backlight, is easy to read—even in the dark.

UtilityPROTM Series
3
SUN
Press day(s) to set program schedule (see page 11)
Displays the current
tier rate
Press to select fan
operation
Press to select system
type
Press to set program
schedule
Press to view
messages
Press to adjust
temperature settings
Press to view the
subscribed service
messages
Press to override
program schedule Press to set clock
Press to lock keypad for 30
seconds to clean screen
Quick Reference to Controls

Operating Manual
SCHED HOLD CLOCK SCREEN USAGE
AM
FAN
AUTO
SYSTEM
HEAT
Following
Schedule
Inside Set To
70
8:10
75
SUN
VIEW
TIER
MEDIUM
Recovery
Current inside temperature
Current day of week
Temperature setting
Program schedule ON
(does not display
when off)
Fan setting
Other display messages:
• Cool ON: Cooling system is activated
• Heat ON: Heating system is activated
• Aux Heat ON: Auxiliary heating system is activated
Quick Reference to Status Display
System setting
Current time
Adaptive Intelligent
Recovery in effect
(see page 17)
4

UtilityPROTM Series
5
Demand Control
This is an energy saving device. At times, thermostat operation may be temporarily adjusted
by a small amount as outlined in your energy provider’s associated program literature. This is
normal operation and is part of the program for which you have enrolled.
Thank you for your participation.

Operating Manual
6
UtilityPro®Features
6
Utility Usages
Usage is a service provided by the utility provider. Depending on the various services
provided by the utility provider, Usage may contain vital information for your use. It
may display your electricity bill, water consumption bill, gas bill, and so on. Usage
also has a feature wherein you can compare your present consumption against
your last year’s consumption for the same time period. For example, it displays
your current electricity bill along with the previous year’s electricity bill for the same
month.
Usage also displays the rate of electricity at peak times and off peak times. Thus you
can adjust your electricity consumption accordingly.
Messages are also a part of the services provided by the service utility provider.
Messages are sent by the service provider to assist you with additional information.
These messages may contain weather warnings, greetings, reminders, information
about discounts running at a shop, system maintenance messages, and so on.
Utility Messages