Eurotramp Ground Trampoline Adventure Outdoor User manual

1
Eurotramp - Trampoline Kurt Hack GmbH
Use, Maintenance and Assembly Instructions
Ground Trampoline Adventure Outdoor (Art.-No. 94xxx)
Ground Trampoline Master/Standard Outdoor (Art.-No. 95xxx)
Ground Trampoline Grand Master Outdoor (Art.-No. 96xxx)
General data ...................................................................................................................................................... 2
Maintenance recommendations........................................................................................................................ 2
Safety instruction for using the trampoline........................................................................................................ 3
Parts list............................................................................................................................................................. 4
Assembly instructions ....................................................................................................................................... 5

2
Eurotramp - Trampoline Kurt Hack GmbH
Art.-No. 94xxx: Ground trampoline Adventure
Outdoor
• Frame dimensions: 300 x 200 cm
• Total weight: 120 kg
Art.-No. 95xxx: Ground trampoline Master/
Standard Outdoor
• Frame dimensions: 464 x 281 cm
• Total weight: 190 kg
The trampoline must always be examined for possible damages before use. Particularly make sure that pads, the
jumping bed, springs and frame parts do not display any damages. Damages must be addressed immediately. In
case of any doubt about whether the apparatus is functional, a specialist advice should be sought (e.g., from the
manufacturer).
Check the following regularly:
• Padding
• Jumping bed
• Springs
Check the apparatus before use and replace all defective or missing parts. Pay particular attention to the following:
• No damages to the jumping bed;
• jumping bed suspension in perfect condition;
• frame does not display any cracks or other damages;
• springs are not damaged or over-extended;
• full frame padding cover is attached properly;
• over-extended and tired springs are to be replaced;
• the important thing is that the springs are always hooked in with the eyelet pointing downwards.
General data
Maintenance recommendations
Art.-No. 96xxx: Ground trampoline Grand
Master Outdoor
• Frame dimensions: 524 x 311 cm
• Total weight: 220 kg
Number of users
Ground trampolines Outdoor correspond with the DIN EN 13 219 norm for sports apparatus and may only be
used by one person at a time. Other persons should therefore not remain on the trampoline. The exceptions
to this rule are coaches or assistants providing support to the gymnast when performing exercises. Use of the
ground trampoline is only permitted under supervision.
Norm: DIN EN 13219

3
Eurotramp - Trampoline Kurt Hack GmbH 33
Enjoy jumping
on the trampoline!
%
First try some small jumps
until you consistently land
in the centre of the jumping
bed. Keep your eyes on the
edges to control jumping.
In doing so, learn the basic
jumps and how to stop the
jump by bending your knees.
The trampoline may only be
used by one person at a
time.
Somersaults and twisting,
backips and belly jumps are
strictly prohibited!
Jump on the trampoline only
as instructed.
This equipment complies
with the norm for sports
apparatus (DIN EN 13219)
and may therefore only be
used under supervision!
Do not jump for too long.
Stop jumping immediately if
you feel dizzy or breathless.
Do not jump on other objects
or people.
Individuals with a pre-existing
medical condition (e.g. spinal
damage) and pregnant
women must not use the
equipment.
Food, drinks, chewing gum
and sweets are absolutely
prohibited while jumping.
Risk of suffocation!
Never jump with shoes,
unstable footwear (e.g. ip-
ops) or bare-footed. Only
permitted with appropriate
trampoline socks.
For safety reasons, remove
jewellery, watches and such
like before jumping.
Strong gusts of wind may
adversely affect jumping on
the trampoline.
There is an increased risk of
falling when using the
trampoline in snow and rain.
Do not jump when under
the inuence of medication,
alcohol or drugs.
Serious injury is caused not just by falling from the trampoline, uncontrolled landing on the jumping bed on the head or neck can
also result in life-threatening injuries. The best protection against accidents and injury is respect when jumping and observation of
a few safety rules. Before using the trampoline, ensure that the equipment is in perfect technical condition.
Safety instructions for using the outdoor trampoline

4
Eurotramp - Trampoline Kurt Hack GmbH
The very highest demands are placed on this high-end-product. For safety reasons, only use original replacement parts! The use
of non-original replacement parts can result in considerable risk to the user (danger of accidents, technical defects, loss of the
manufacturer’s liability, loss of warranty etc.).
Parts list (scope of delivery)
Art.-No. 94xxx: GroundTrampoline Adventure Outdoor Quantity
Frame part 300 x 12 cm, hot-dip galvanized 2
Frame part 200 x 12 cm, hot-dip galvanized 2
Jumping bed 212 x 112 cm made of PVC 1
Steel spring 235 x 30 mm, hot-dip galvanized 62
Frame padding cover for long side 2
Frame padding cover for short side 2
Black belt 1
Steel spring 235 mm, hot-dip galvanized – for fastening black belt 4
Velcro, self-adhesive 1
Spring clip 6
Mounting tool 1
PVC Safety sign 1
Art.-No. 95xxx: GroundTrampoline Master/Standard Outdoor Quantity
Frame part 464 x 12 cm, hot-dip galvanized 2
Frame part 281 x 12 cm, hot-dip galvanized 2
Jumping bed 366 x 183 cm made of PVC 1
Steel spring 235 x 30 mm, hot-dip galvanized 100
Frame padding cover for long side 2
Frame padding cover for short side 2
Black belt 1
Steel spring 235 mm, hot-dip galvanized – for fastening black belt 4
Velcro, self-adhesive 1
Spring clip 8
Mounting tool 1
PVC Safety sign 1
Art.-No. 96xxx: GroundTrampoline Grand Master Outdoor Quantity
Frame part 524 x 12 cm, hot-dip galvanized 2
Frame part 311 x 12 cm, hot-dip galvanized 2
Jumping bed 426 x 213 cm made of PVC 1
Steel spring 235 x 30 mm, hot-dip galvanized 118
Frame padding cover for long side 2
Frame padding cover for short side 2
Black belt 1
Steel spring 235 mm, hot-dip galvanized – for fastening black belt 4
Velcro, self-adhesive 1
Spring clip 12
Mounting tool 1
PVC Safety sign 1
All spare parts available from Eurotramp upon request.
!

5
Eurotramp - Trampoline Kurt Hack GmbH
Digging the pit
In accordance with the installation drawing for the respective ground trampoline (see CAD drawings on pages 7–9
for dimensions).
• The type of pit arrangement and the area surrounding the pit depend on the individual case or local
conditions. Ask the landscaper or construction company digging out the pit in case of any doubt.
• Pit edge reinforcement is essential if the base is not stable (e.g. sandy) and the pit edges crumble away.
A fully circumferential foundation can be placed in the pit on which the frame parts are positioned or the
corresponding bases can be at least planned in the corners. For the Grand Master ground trampoline, a
xed support base should be available, at least on the long sides, so that the longitudinal frame parts can be
screwed to the base. Eurotramp recommends installing foundations measuring 60 x 40 cm, and 60 cm deep
at the four corners and in the centre of the frame pro le in a lengthways direction respectively.
• If the trampoline is to be placed on the pit edge without the pit being xed with a foundation, the side walls
can run at a slight angle as shown in the installation drawing. To prevent the ground from subsequently
slipping, it should be compacted by machine before extraction. These walls can also be stabilised with xing
elements available in the respective DIY stores. We recommend dropping the frame in at ground level. If the
frame is to be recessed, the frame padding is xed with Velcro.
• The soil extraction is approx. 13 cubic metres for the Standard ground trampoline and approx. 19 cubic
metres for the Grand Master ground trampoline.
• Always make sure that the pit base must have a drainage possibility (e.g. layer of pebbles) so that the water
can soak into the ground. There is the risk of the pit lling up with water if the base is not permeable (clay or
cement layer).
• The design of the area surrounding the ground trampoline depends on the special conditions in the individual
case. If the ground around the ground trampoline is very hard, an impact absorbing layer around the
trampoline may need to be planned so that the impact of a fall is absorbed. It must be ascertained whether
legal regulations (e.g. in playgrounds) need to be observed.
Assembly instructions
Safety accessories required
• Safety gloves (not in scope of
delivery)
Assembly: Workforce
• The assembly should be carried
out by two persons.
Attention: the trampoline may only be installed on a at
surface and under no circumstances on a mound, incline
or slope edge.

6
Eurotramp - Trampoline Kurt Hack GmbH
Mounting instructions for all ground trampolines
Allow for at least 1,5 m of shock absorbing ground material around the trampoline e.g. lawn, safety slabs or
equivalent.
Exemplary displayed here: GroundTrampoline Adventure. Instructions are valid for all kinds of ground trmapolines!
F
E
D
C
B
A
1
23 4
1
23 4
Datum Name
Bearb.
Gepr.
Maßstab Werkstoff
Rohteil/Halbzeug/Ausgangsteil
Benennung:
Copyright by Eurotramp. All right reserved. Referred to protection notice ISO 16016
Ähnlich: Ers. für:
Zeichnungs - Nr.:
Model - NR.:
Name
Datum
Änd - Nr.:
Ä-Ind
Blatt:
Eurotramp-Trampoline
Kurt Hack GmbH
conrad05.06.2013
Bodentrampolin
Einbauhinweis
Adventure zusammenbau
Eurotramp
PLOTUSER 00.00.0000
1
1:30
1
Blattgröße: A4
/
15001500
1500 1500

7
Eurotramp - Trampoline Kurt Hack GmbH
Installation draft ground trampoline Adventure Outdoor
A-A ( 1 : 20 )
B-B ( 1 : 20 )
2Rahmenprofil 30001 2Rahmenprofil 20002
62Zugfeder3
1Sprungtuch3
4Kettenglid DIN 76311
8Federbügel zur
Polsterhochhaltung
12
2Polster längs13 2Polster quer14
4Polsterfeder15
1Gurtband16
Stückliste
St.BezeichnungPos
A
A
B B
12 3 456 7 8
F
23 4 5 67 81
A
B
C D
E
A
B
C
D
E
F
Datum Name
Bearb.
Gepr.
Maßstab Werkstoff
Rohteil/Halbzeug/Ausgangsteil
Benennung:
Copyright by Eurotramp. All right reserved. Referred to protection notice ISO 16016
Ähnlich: Ers. für:
Zeichnungs - Nr.:
Model - NR.:
Name
Datum
Änd - Nr.:
Ä-Ind
Blatt:
Eurotramp-Trampoline
Kurt Hack GmbH
conrad09.12.2011
Adventure
Adventure
Einbauzeichnung
Eurotramp
Adventure zusammenbau
Eurotramp
PLOTUSER 00.00.0000
1
1:20
1
Blattgröße: A3
/
Anordnung von Polsterbügeln kann Abweichen array of torsion springs may vary
min. 2000
min. 1000
910 10
Sprungbereich/
jumping area
194010 Sprungbereich/jumping area
2000 Rahmen/frame
3000 Rahmen/frame
Drainage vorsehen/arrange for drainage
100-120 Auflage/support area
970
min.
60 Rahmen/frame
32 Polster/padding
2120 Tuch/jumping bed
1110 Tuch 7 jumping bed
100 Rahmen/frame

8
Eurotramp - Trampoline Kurt Hack GmbH
Installation draft ground trampoline Master/Standard Outdoor
A-A ( 1 : 30 )
B-B ( 1 : 30 )
A A
B B
12 3 456 7 8
F
23 4 5 67 81
A
B
C D
E
A
B
C
D
E
F
Datum Name
Bearb.
Gepr.
Maßstab Werkstoff
Rohteil/Halbzeug/Ausgangsteil
Benennung:
Copyright by Eurotramp. All right reserved. Referred to protection notice ISO 16016
Ähnlich: Ers. für:
Zeichnungs - Nr.:
Model - NR.:
Name
Datum
Änd - Nr.:
Ä-Ind
Blatt:
Eurotramp-Trampoline
Kurt Hack GmbH
conrad08.11.2012
Bodentrampolin
Master in Grube
Bodentrampolin Master in
Grube
PLOTUSER 00.00.0000
1
1:30
1
Blattgröße: A3
/
1150 min. 1000
120
60
100-150 Auflagefläche/area of support
4640Rahmen/frame
2810 Rahmen/frame
1810 Sprungtuch/jumping bed
3620Sprungtuch/jumping bed
Gelände/surrounding terrain
min. 3200
min. 1370
33 Federn auf langer Seite/springs on long side
17 Federn auf kurzer Seite/springs on short side
Drainage vorsehen/arrange for drainage
Maßeinheit/dimension unit: mm

9
Eurotramp - Trampoline Kurt Hack GmbH
Installation draft ground trampoline Grand Master Outdoor
A-A ( 1 : 30 )
B-B ( 1 : 30 )
A A
B B
12 3 456 7 8
F
23 4 5 67 81
A
B
C D
E
A
B
C
D
E
F
Datum Name
Bearb.
Gepr.
Maßstab Werkstoff
Rohteil/Halbzeug/Ausgangsteil
Benennung:
Copyright by Eurotramp. All right reserved. Referred to protection notice ISO 16016
Ähnlich: Ers. für:
Zeichnungs - Nr.:
Model - NR.:
Name
Datum
Änd - Nr.:
Ä-Ind
Blatt:
Eurotramp-Trampoline
Kurt Hack GmbH
conrad08.11.2012
Bodentrampolin
Grandmaster in
Grube
Bodentrampolin Grand Master
in Grube
PLOTUSER 00.00.0000
1
1:30
1
Blattgröße: A3
/
1150
120
60
100-150 Auflagefläche/area of support
3110 Rahmen/frame
5240Rahmen/frame
2130 Sprungtuch/jumping bed
4260Sprungtuch/jumping bed
Gelände/surrounding terrain
39 Federn auf langer Seite/springs on long side
20 Federn auf kurzer Seite/springs on short side
min. 3800
min. 1670
Drainage vorsehen/arrange for drainage
Maßeinheit/dimension unit: mm

10
Eurotramp - Trampoline Kurt Hack GmbH
Assembling the ground trampoline frame
1
2 3

11
Eurotramp - Trampoline Kurt Hack GmbH
Jumping bed assembly (with the stamped side / cross facing up)
• Hang in 2 steel springs per corner rst of all to
x the jumping bed.
• Hook the springs onto the jumping bed.
• Then hook the springs with the mounting tool
on the long sides onto the frame rst.
• Always hook the springs on opposite sides
in at the same time to prevent unnecessary
excess tension on the springs.
• Now attacht the short side.
• Here also hook the springs on opposite sides
in at the same time to prevent unnecessary
excess tension on the springs.
1
3
2
Required material
• Mounting tool
• Safety gloves (not in scope of delivery)
The jumping bed should preferable be attached by 2 persons
Important:
the spring ears
should point
downwards!

12
Eurotramp - Trampoline Kurt Hack GmbH
Black belt assembly
• hang the black belt into the four corner
eyelets.
Amount of spring clips: Adventure 6 pieces;
Master/Standard 8 pieces; Grand Master 12
pieces.
• Hang the leg springs on the suspension hooks
according to the drawing so that the black belt
lies between the legs on the springs.
• Always leave a spring between the spring clip
leg.
• Hang the spring brackets into the long sides
and top ends. The spring brackets with the
black belt prevent direct contact between the
padding and springs.
1
3
2
Spring clip assembly

13
Eurotramp - Trampoline Kurt Hack GmbH
Frame padding installation
• Attach the remaining velcro on the corners
of the steel frame. This prevents accidental
contact with the steel tube.
• Place the long pad on one corner and apply
light pressure to x it to the frame.
• Position the short pad to line up and also
apply light pressure to x it to the frame.
• Fix protruding tabs at the corners with the
outer edge of the frame.
• Remove the foil on the supplied Velcro and
attach around the upper side of the frame
with approx. 10 mm clearance from the
outside.
Done!
1
Attention: never connect the
padding to the juming bed.
3
2
ca. 10 mm
If you have any questions, contact us any time:
EurotrampTrampoline - Kurt Hack GmbH
Zeller Straße 17/1
73235 Weilheim
Tel. [phone] - 9495-0 | Fax [phone] - 9495-10
[email protected] | www.eurotramp.com
5
4