Evantair TWOC200-7T User manual

For Models: TWOC200-7T, TWOC200-9T, TWOC200-11TH
OIL COLUMN HEATER WITH TIMER
OPERATING INSTRUCTIONS

1. Use only the voltage specified on the rating
label of the appliance.
2. Keep all objects at least 1 metre from the front,
sides and rear of the appliance. Do not place
appliance close to radiant heat source.
3. Do not operate in areas where petrol, paint or
other flammable liquids are used or stored.
4. Do not insert or allow foreign objects to enter
any ventilation or exhaust opening, as this may
cause an electric shock, fire or damage to the
appliance. Do not sit on the appliance.
5. Do not operate this appliance with a damaged
cord, plug or after the appliance malfunctions
or has been dropped or damaged in any
manner. Return to a qualified electrical person
for examination, electrical service or repair.
6. This appliance is intended for household use
only and not for commercial or industrial use.
7. Use this appliance only as described in this
manual. Any other use is not recommended by
the manufacturer and may cause fire, electrical
shock or injury.
8. The common cause of overheating is deposits
of dust or fluff in the appliance. Ensure these
deposits are removed regularly by unplugging
the appliance and vacuum cleaning the air
vents and grills.
9. Do not use abrasive cleaning products on this
appliance. Clean with a damp cloth (not wet)
rinsed in hot soapy water only. Always remove
plug from the mains supply before cleaning.
10. Do not connect the appliance to mains supply
until completely assembled and adjusted.
11. Switch off and use handles provided when
moving.
12. Do not operate with cord set coiled up as a
heat build up is likely, which could be sufficient
to become a hazard.
13. Do not use an extension cord, powerboard or
external timer with this appliance.
14. Do not remove plug from power socket until the
appliance has been switched off.
15. Do not remove plug from power socket by
pulling cord; always grip plug.
16. Always unplug appliance when not in use.
17. Do not locate the heater directly below any
power socket during operation.
18. Do not twist, kink or wrap the cord around the
appliance, as this may cause the insulation to
weaken and split. Always ensure that all cord
has been removed from any cord storage area
and is unrolled before use.
19. This appliance is not intended for use by
persons (including children) with reduced
physical, sensory or mental capabilities or lack
of experience and knowledge, unless they are
supervised or have been given instruction
concerning the use of the appliance by a
person responsible for their safety.
20. Do not use this appliance in the immediate
surrounds of a bath, a shower, or a swimming
pool or other liquids. The appliance must not
be immersed in any liquids.
21. When the appliance has been unpacked,
check it for transport damage and ensure all
parts have been delivered. If parts are missing
or the appliance has been damaged, contact
the Evantair Customer Services Team. (refer to
details later in manual)
22. If your appliance does not work, or is not
working properly, contact the place of purchase
or the Evantair Customer Services Team.
(refer to details later in manual). Repair work
on the appliance by unqualified persons can
cause serious risk to the user.
23. There are no user serviceable parts installed in
the unit.
24. Do not place the unit in wardrobes or other
enclosed spaces as this may cause fire
hazards.
25. This unit is not supposed to be used in or
around locations where foodstuffs, works of art
or delicate articles of science, etc are stored.
26. Indoor use only.
27. Children should be supervised to ensure that
they do not play with the appliance.
28. Ensure heater is on a flat, stable, heat-resistant
surface.
29. It is important that you do not cover this heater.
WARNINGSAND SAFEGUARDS
SUPPORTAND TECHNICALADVICE
North Shore City, Auckland, New Zealand
Monday –Friday 8am-5pm
Phone: [phone]

COMPONENTS
Main Body x1
Wing Nut x2
U-shape Bolt x2
Wheel Castor x2
TWOC200-7T, TWOC200-9T
A. Main body fin
B. Handle
C. Adjustable thermostat
D. Power switch
E. Timer
F. Cable plate
G. Wheel assembly
H. Wheel
A
B
C
D
E
F
G
H
TWOC200-11TH
A. Main body fin
B. Handle
C. Adjustable thermostat
D. Power switch
E. Timer
F. Fan button
G. Cable plate
H. Wheel assembly
I. Wheel

ASSEMBLY OF THE HEATER
Carefully turn the Main Body upside-down on a non-scratching and stable surface. Be careful to prevent
damage to the paint finish or your floor surfacing (Fig.1).
Fit the wheel assemblies onto the Main Body by placing the U-shaped bolts between the outermost fins on
each side of the Main Body (see Fig.2 - 4).
Securely fasten the wheel assemblies onto the Main Body by screwing the wing nuts onto the U-shaped
bolts (see Fig. 5).
IMPORTANT: Please fit the wheel assemblies as per the diagram. Any other position may affect the stability
of the heater.
WARNING: Operate the Main Body in normal upright position only with wheel assemblies attached to the
bottom, any other position could create a hazardous situation.
ASSEMBLY

OPERATING YOUR OIL COLUMN HEATER
Always choose a safe location for the heater, keeping in mind the safety precautions outlined.
Ensure all packaging has been removed from the unit before use. This appliance requires no
installation, it should be used solely as a portable appliance.
WARNING: Keep all objects at least 1 metre from the front, sides and rear of the appliance.
PLEASE NOTE: As this heater is fitted with a Timer, the Timer has been set to the “ON” position.
Please refer to the Timer section of this manual for setting instructions.
HEAT CONTROL SWITCH
The control switch positions are:
●Low heating
●● Medium heating
●●● High heating
Check that the power On/Off switch is set to Off position before plugging the heater into the mains supply.
For greater economy, use the High Heat setting initially and then switch to the Low Heat setting.
THERMOSTAT
Turn the thermostat knob clockwise until you reach the maximum temperature on the graduated scale.
When the desired room temperature is reached, slowly turn the knob anti-clockwise until the heater turns
off (you will hear a click). The heater will now cycle on and off to maintain the set temperature.
TURBO/CERAMIC HEATER (TWOC200-11TH model only)
The Turbo function is for supplying heat instantly whilst the main heater warms up. For Turbo heat, switch
the Turbo ON/OFF using the Fan button on the front of the Turbo cover.
IMPORTANT! NEVER COVER THIS HEATER
SAFETY DEVICE
This appliance has three protection devices:
The first device will automatically turn the appliance off if the appliance is not in the appropriate operating
position.
The second device automatically disconnects & reconnects the appliance at a pre-set temperature.
The third device disconnects the appliance permanently in case of overheating, by means of a thermal
fuse. (It is non resettable)
Do not attempt to dismantle the heater. There are no user serviceable parts. For service or repair, contact
an authorised electrical service technician.
WARNING: Do not use this heater with a programmer, separate timer, remote-control system or any other
device that switches the heater on automatically, since a fire risk exists if the heater is covered or
positioned incorrectly.
CAUTION: The heater generates heat during use. Proper precautions must be taken to prevent the risk of
burns, scalds, fires or other damage to persons.
PROOF OF PURCHASE
To receive warranty retain receipt as proof of purchase.

TIMER
You must set the time prior to programming the Timer. To do this turn; the outer dial of the timer in a
clockwise direction until the time of the day (24-hour clock) corresponds with the triangular marking.
Example if it is 2pm (1400 hours) then set the triangular mark in line with 14. One complete turn of the dial
corresponds to 24 hours.
There are 96 “riders”, positioned around the dial, each rider represents 15 minutes.
Where all the “riders” are pushed to the outside of the timer the heater will be ON continuously.
To set a specific time for example:
If you want the heater to be on from 6pm to 10pm, then set all the riders from 18 to 22 (1800 hours to 2200
hours) to the outside of the rim and all other riders to the inside of the timer. The unit will then turn on
automatically at 6pm and off again at 10pm.
WARNING: Take care in positioning your heater. Using the Timer will mean the heater will come on
automatically. Fire may result if the heater has been placed next to combustible material.
Indicates actual time
Riders pushed to the
outside rim to turn
ON
TECHNICAL SPECIFICATION
Model No: TWOC200-7T
Supply: 220-240VAC 50Hz
Wattage: 1500W
Model No: TWOC200-9T
Supply: 220-240VAC 50Hz
Wattage: 2000W
Model No: TWOC200-11TH
Supply: 230-240VAC 50Hz
Wattage: 2300-2400W

Your Evantair product has been inspected and tested and is guaranteed subject to
the following for a period to two years from the date of purchase against defects in
workmanship and materials. During this period, such defects will be rectified by
repair or replacement of the product purchased. Your product contains no user
serviceable components and this warranty becomes invalid if in our opinion the
product has been misused, abused, incorrectly installed, tampered with, connected
to an electrical supply not corresponding with the name plate specification, or
subjected to power surges. The warranty does not include any labour or other
associated expense that may be involved in removal or installation of the product.
Normal wear and tear is expressly excluded.
If your Evantair product fails to operate satisfactorily, please return it to the retailer
from whom it was purchased. To obtain a repair or replacement product under this
warranty, you will need to produce satisfactory evidence of date of purchase. The
completed warranty and purchase receipt must be presented with the product. The
warranty should be filled out at the time of purchase. It is in your interest to make
sure this is done.
If the product is to be replaced (cannot be repaired) then that replacement will be of
the same or similar product or accessory excluding packaging, instruction card etc.
Where a replacement product is supplied, this shall be guaranteed for the balance of
the original warranty period.
Any model that is no longer available will be replaced by a model of a value and with
such features as we consider appropriate in the circumstances. Evantair Ltd is not
responsible for freight forwarding charges, losses or damage in transit.
If service is required after the warranty period has expired, the product should be
returned to a qualified electrical technician. Service outside of the warranty period
will be at your cost.
Consumers GuaranteeAct (1993).
In accordance with the above act consumers are advised that: The manufacturer
does not undertake that repair facilities and parts are necessarily available for this
product.
If any of the provisions of the foregoing are contrary to any relevant legislation, then
that provision shall be deemed to be excluded from the warranty and the rest of the
provisions will continue to apply.
TWO YEAR WARRANTY
IMPORTANT: PLEASE RETAIN THIS WARRANTY CARD
NAME:
ADDRESS:
PURCHASED FROM:
SUBURB:
DATE OF PURCHASE:
NAME OF PRODUCT:
MODEL No:
.