EverFocus EHN3200 User manual

EHN3200
User’s Manual
Copyright © EverFocus Electronics Corp,
Release: Apr. 2011 Rev. 0

EHN3200
2
Product Name: EHN3200 EverFocus IP Network Cameras
Model Number(s): EHN3200
FCC Notice "Declaration of Conformity Information"
This equipment has been tested and found to comply with the limits for a Class
A digital device, pursuant to part 15 of the FCC Rules. These limits are designed
to provide reasonable protection against harmful interference in a residential
Installation. This equipment generates, uses and can radiate radio frequency energy
and, if not installed and used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
Warning: Changes or modifications made to this equipment, not expressly approved
by EverFocus or parties authorized by EverFocus could void the user's authority to
operate the equipment.
This device complies with part 15 of the FCC Rules. Operation is subject to the
following two conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including interference that
may cause undesired operation.
EverFocus Electronics Corp.
12F, No. 79, Sec. 1, Shin-Tai Wu Rd., His-Chi,
Taipei Hsien, Taiwan, R.O.C.
EHN3200 complies with CE and FCC rules.

EHN3200
3
About this document
All the safety and operating instructions should be read and followed before the
unit is operated. This manual should be retained for future reference. The
information in this manual was current when published. The manufacturer reserves
the right to revise and improve its products. All specifications are therefore subject
to change without notice.
Safety Notices
-These limits are designed to provide reasonable protection against interference.
This equipment may generates, uses and can radiate radio frequency energy and, if
not installed and used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
-Reorient or relocate the receiving antenna.
-Increase these separations between the equipment and receiver.
-Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
-Consult the dealer or an experienced radio/TV technician for help.
Any changes or modifications not expressly approved by the party responsible for
compliance could void the user's authority to operate the equipment.
To reduce risk of fire or electric shock, do not expose this camera to rain or
moisture.
Do not attempt to disassemble the camera. To prevent electric shock, do not
remove screws or covers. There are no user-serviceable parts inside. Contact
qualified service personnel for maintenance. Handle the camera with care. Do not
strike or shake, as this may damage the camera.
Do not use strong or abrasive detergents when cleaning the camera body. Use
a dry cloth to clean the camera when it is dirty. When the dirt is hard to remove,

EHN3200
4
use a mild detergent and wipe gently.
Do not operate the camera beyond its specified temperature, humidity or
power source ratings. Do not use the camera in an extreme environment where high
temperature or high humidity exists. Use the camera at temperature within -10°C
~50°C / 14°F~122°F and a humidity below 90%. The input power source for this
camera is 12 VDC & 802.3af PoE.
Use only the recommended power supplies. Power supplies must comply
with the requirement of the latest version of IEC60950-1. Substitutions may
damage the unit or cause a fire or shock hazard.
Electrostatic-sensitive device. Use proper CMOS/MOSFET handing
precautions to avoid electrostatic discharge.
Installation should be performed by qualified service personnel only in
accordance with the National Electrical Code or applicable local codes.
Terms and Trademark
Ethernet, Internet Explorer, Linux, Microsoft, Windows, WWW are registered
trademarks of the respective holders. Other product names appearing in this User's
Guide may be trademarks or registered trademarks of their respective holders.
Java™ and all Java-related logos and trademarks are trademarks or registered
trademarks of Sun Microsystems, Inc. in the United States and other countries.
Support
If the unit ever needs repair service, the customer should contact the nearest
EverFocus Electronics Corp. Service Center for return authorization and shipping
instruction.
About this AC Adaptor
Specifications for AC adaptor
Power Supply: 12VDC, 1 A
Power Output: 12VDC, 1 A
Operating Temperature: 0℃~ 40℃/ 32۫F ~ 104۫F
External Dimensions: 56 mm x 68 mm x 101 mm / 2.24” x 2.72” x 4.04”

EHN3200
5
TABLE OF CONTENTS
1. INTRODUCTION....................................................................................................6
2. FEATURES..............................................................................................................6
3. ACCESSING THE CAMERA MENU ...................................................................7
4. PLAYBACK ...........................................................................................................11
5. SETTING................................................................................................................13
5.1 SYSTEM INFO ......................................................................................................13
5.1.1 Information Tab...........................................................................................13
5.1.2 Log Tab .......................................................................................................14
5.2 USER CONFIG ......................................................................................................15
5.3 NETWORK ...........................................................................................................17
5.3.1 Network.......................................................................................................17
5.3.2 DDNS..........................................................................................................20
5.3.3 SMTP/FTP ..................................................................................................21
5.3.4 SNMP..........................................................................................................23
5.3.5 Network Alarm (reserved for PowerCon)...................................................25
5.4 VIDEO .................................................................................................................26
5.4.1 Multi Streaming ..........................................................................................26
5.4.2 Camera ........................................................................................................29
5.4.3 Advanced.....................................................................................................31
5.4.4 Privacy Mask ...........................................................................................32
5.5 AUDIO .................................................................................................................33
5.6 USER .................................................................................................................34
5.7 EVENT...............................................................................................................35
5.7.1 Event Settings .............................................................................................36
5.7.2 Motion Detection ........................................................................................38
5.7.3 Alarm I/O ....................................................................................................39
5.7.4 Schedule......................................................................................................40
5.8 SYSTEM............................................................................................................41
5.8.1 Date/Time....................................................................................................41
5.8.2 Daylight Saving ..........................................................................................43
5.8.3 SD Card.......................................................................................................44
5.8.4 Maintenance................................................................................................46

EHN3200
6
1. INTRODUCTION
EverFocus EHN3200 enable to delivers HDTV video with superior image
quality at up to 30fps in 1080p resolution, with true day/night ICR module
functionality plus up to 4X ‘sens-up’ for low light image enhancement. With the
capability for dual simultaneous, independently configurable streams, the
EHN3200 supports both H.264 and MJPEG compression formats. Power over
Ethernet (IEEE 802.3af) allows the camera to be powered via the network cable
for ease of installation; eliminating the need for power cables can reduce
installation costs; or, use conventional network wiring and power the camera
from a separate 12VDC supply. IP66 rated weather-proof and vandal-resistant
design, and Power over Ethernet (PoE), the EHN3200 is a durable network dome
camera suited with features for the most demanding environments.
2. FEATURES
1/2.7” 1080p/720p HD color CMOS image sensor delivers HDTV video
quality in 16:9 aspect ratio
Supports both H.264 and Motion JPEG in full 30 FPS frame rate.
High Performance Noise Filter improves image quality
Provides NTSC/PAL TV Signal ‘test mode’ output for local aim and focus
or display on an analog monitor.
Dual Codec for H.264 and MJPEG allows choice of stream formats to fit the
application
Built-in slot for an SDHC card enables local event or backup recording in the
event of network interruptions
Provides true day/night functionality with automatic IR filter operation
Up to 4X ‘sens-up’ low light enhancement
Two Way Audio transport (line level input/output)
ONVIF / PSIA compliance interoperates with a broad range of systems
Dual power capability PoE or 12VDC for flexible installation
Local alarm inputs and outputs
Vandal Resistant & Weatherproof IP66 rated

EHN3200
7
3. ACCESSING THE CAMERA MENU
Step 1. Start an Internet Explorer browser session. Before accessing to the
EHN3200 over IE browser, user should adjust the security level.
Open the IE browser and set the security level to “Low” in
“Tools->InternetOptions->Security->CustomLevel…”, and enable ActiveX
Control and Plug-in directly as well.
Step 2. Enter the IP address or host name of the camera in the Location/Address
field of your Internet Explorer browser in the form http://nn.nn.nn.nn:port, or
http://ddnsname.everfocusddns.com. (Please refer to EHN3200 Installation
Guide for how to find the IP address by using the IP Finder)
Step 3. At the login popup window enter “User Name” and “Password”. Default
User name is “user1” and default password is “11111111”.
Step 4. Click “OK” button.

EHN3200
8
Step 5. You might be required to download Active X files, which are required to
process camera video. Please click "Install".
Step 6. Congratulations!! You should now be able to see the live image.
○
16
○
17
○
18
○
15
○
1
○
2
○
10
○
8
○
7
○
3
○
4
○
6
○
5
○
9
○
14
○
13
○
12
○
11

EHN3200
9
○
1Press button to display the "Live" page.
Double click on the image to show a full screen display, double click again or press
ESC to return to the normal live display.
○
2Press button to go SD card playback page. Please refer to
“Section 4. Playback" for further information.
○
3Press button to enter the camera Setting page. In the
Setting page, there are 8 sections: [System Info], [User Config], [Network], [Video],
[Audio], [User], [Event] and [System]. Please refer to “Section 5. Setting” for further
information.
○
4Press button to close the EHN3200 network page.
○
5Video Stream
Select the desired Video Stream from Stream 1 and Stream 2 (stream must be enabled
in camera Setting menu). Please refer to "Section 5.4.1 Multi Streaming” for further
information.
○
6View Size
You can select View size to either reduce or enlarge the image to the appropriate size.
Select the view size for live images from:
1920x1080/1280x1024/1280x720/1024x768/800x600/720x480(720x576)/640x480/3
52x240(352x288)/320x240
○
7~ ○ 8Digital Zoom
Press “+” or “-“ button or roll the mouse wheel to magnify / reduce the displayed
image. (max. is X10) Clicking on a magnified image will re-center the image around
that point.

EHN3200
10
○
9Record
The record button is used to record the current video stream. The location
where the image file is saved can be specified in Setting -> User Config. Please refer
to “Section 5.2 User Config” for further information.
Note: Record segment is unlimited. However, if you switch to any other page, record
will stop.
○
10 Snapshot
The Snapshot button saves a .jpg image of the video image currently being displayed.
The location where the snapshot data is saved can be specified in Setting -> User
Config. Please refer to “Section 5.2 User Config” for further information.
○
11 ~ ○ 12 Play Audio/Transmit Audio
Click the “Play Audio” and “Transmit Audio” buttons to switch the sound off and on
for the audio input and output, respectively.
○
13 Manual Control – Trigger Event
Press “Trigger Event” button to trigger an event directly from the live view page, and
event actions will be initiated if they have been set up in the “Event” menu. (Please
refer to “Section 5.7.1 Event Settings”)
○
14 Manual Control – Reset Alarm
Press “Reset Alarm” button to reset an alarm condition remotely.
○
15 The icon is used to fold the control panel at left and view the image in a full
screen. Click on icon to unfold the control panel.
○
16 Status Display
The name of the camera currently being viewed, current date/time and current frame
rate will be displayed.
○
17 Event signals
When an alarm or motion event is triggered, a signal icon will flash to alert the user.
The first icon is for alarm events and the other 5 icons are for motion events. The
motion event icons, which differ by color, correspond to the motion trigger areas set
in the Motion menu. Please refer to “Section 5.7.2 Motion” for detailed information