EverFocus eZ.HD EBD930F User manual

EBD930FeZ.HD Series
1080p Full High Definition
True Day/Night Outdoor IR Ball Camera
User’s Manual
Copyright © EverFocus Electronics Corp.
Release Date: February 2016

2
Precautions
1. Do not install the camera near electric or magnetic fields. Install the camera away from
TV/radio transmitters, magnets, electric motors, transformers and audio speakers since the
electromagnetic fields generated from these devices may distort the video image or
otherwise interfere with camera operation.
2. Never disassemble the camera beyond the recommendations in this manual nor introduce
materials other than those recommended herein. Improper disassembly or introduction of
corrosive materials may result in equipment failure or other damage.
3. Try to avoid facing the camera toward the sun. In some circumstances, direct sunlight may
cause permanent damage to the sensor and/or internal circuits, as well as creating
unbalanced illumination beyond the capability of the camera to compensate.
4. Keep the power cable away from water and other liquids and never touch the power cord
with wet hands. Touching a wet power cord with your hands or touching the power cord
with wet hands may result in electric shock.
5. Never install the camera in areas exposed to oil, gas or solvents. Oil, gas or solvents may
result in equipment failure, electric shock or, in extreme cases, fire.
6. Cleaning. For cameras with interchangeable lenses, do not touch the surface of the sensor
directly with the hands. Use lens tissue or a cotton tipped applicator and ethanol to clean
the sensor and the camera lens. Use a damp soft cloth to remove any dirt from the camera
body. Please do not use complex solvents, corrosive or abrasive agents for cleaning of any
part of the camera.
7. Do not operate the camera beyond the specified temperature, humidity or power source
ratings. This camera is suitable for indoor operation only. Use the camera at temperatures
within -10°C~50°C (14°F~122°F) and humidity less than 80%; this device is not rated as
submersible. The input power source is 12VDC. Be sure to connect the proper + / - polarity
and voltage, as incorrect polarity or too high a voltage will likely cause the camera to fail,
and such damage is not covered by the warranty.
8. Mounting. Use care in selecting a solid mounting surface which will support the weight of
the camera plus any wind, snow, ice or other loading, and securely attach the camera to the
mounting surface using screws and anchors which will properly support the camera. If
necessary (e.g. when mounting to drop ceilings) use a safety wire to provide additional
support for the camera.

3
Safety Notice
Federal Communication Commission Interference Statement
This equipment has been tested and found to comply with the limits for a Class A digital device,
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment generates uses and
can radiate radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception, which can be determined by turning
the equipment off and on, the user is encouraged to try to correct the interference by one of the
following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver
is connected.
- Consult the dealer or an experienced radio/TV technician for help.
FCC Caution: Any changes or modifications not expressly approved by the party responsible for
compliance could void the user's authority to operate this equipment.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two
conditions: (1) This device may not cause harmful interference, and (2) this device must accept
any interference received, including interference that may cause undesired operation.

4
Contents
1. Introduction...................................................................................................................... 5
1.1 Packing List .....................................................................................................................5
1.2 Features ..........................................................................................................................5
2. Cable Description.............................................................................................................. 6
3. Installation ....................................................................................................................... 7
3.1 Installation and Adjustment ...........................................................................................7
4. Configuration in the OSD Menu........................................................................................11
5. Specifications...................................................................................................................15

EBD930F eZ.HD IR Mini Ball Camera
5
1. Introduction
The EverFocus eZ.HD Series EBD930F ball camera is equipped with a 1/2.9" SONY 2.24M pixels
CMOS sensor and providing high resolution of 1080p. Featured with the Digital Wide Dynamic
Range (D-WDR) function, the camera can provide clear images even under back light circumstances
where intensity of illumination can vary excessively.
The EBD930F comes with 24 IR LEDs, supporting up to 15m (~50ft.) IR distance in night vision. The
camera can work in both indoor and outdoor environments. The IP66-rating and vandal proof
housing make it suitable for outdoor use. The EBD930F supports both NTSC and PAL scanning
systems, which can be switched via OSD.
1.1 Packing List
1.2 Features
1080p full HD with high flexibility and performance for astounding image
1/2.9" SONY 2.24M pixels CMOS sensor, delivering amazing high sensitivity
Astounding image quality from the 3.6mm/6mm lens
Extended IR range of up to 15M/50ft. with 24 LEDs (depending on scene IR reflectivity)
D-WDR to improve the visibility under high contrast scene
3D Noise Reduction ensures less blurry moving subjects, vivid and high SN ratio
images even under low light environments
Supports 1080p, 720p & 960H analog signal output, which can be easily switched using
OSD Joystick
Special design, easy installation and operation
eZ.Controller function : Control camera OSD settings and PTZ operation from DVR end
Camera Body x 1 Mounting Screw x 4
User Manual x 1 Plastic Anchor x 4
DC Power Pigtail Cable x 1
Set Screw x 2
Warning Paper x 1
Hexagon Wrench x 1
Template Plate x 1

EBD930F eZ.HD IR Mini Ball Camera
6
2. Cable Description
No. Name Descriptions
1 Power Cable Connect to a 12VDC power source.
2 Video Output 1080p, 720p and 960H output, using a 75 Ohm BNC-type
coaxial cable.
3 DC Power Pigtail Cable Optional power pigtail cable. The red wire is positive (+);
while the black wire is negative (-).

EBD930F eZ.HD IR Mini Ball Camera
7
3. Installation
3.1 Installation and Adjustment
1. For Ceiling Mount / Wall Mount users: Stick the Template Plate on the position where you
want to attach the camera.
2. Drill four holes according to the supplied Template Plate, and insert the supplied Plastic
Anchors into the holes.
If you wish to run the wires through the wall / ceiling, drill an additional hole in the
middle of Template Plate.

EBD930F eZ.HD IR Mini Ball Camera
8
3. Unscrew the outer housing by twisting it counterclockwise and then remove the outer
housing from the camera base.
4. Screw the base plate to the wall or ceiling with supplied four Screws and Hexagon
Wrench.
a. If you want to wire the cables from the side cut of the camera base, attach the camera
body to the base plate and run the cables through the camera base first, then screw
the camera base to the ceiling / wall.

EBD930F eZ.HD IR Mini Ball Camera
9
b. If you want to wire the cables through the wall, attach and screw the camera base to
the ceiling / wall. Then attach the camera body to the base plate.
5. Connect the camera to the 12VDC power source using the supplied DC Power Pigtail
Cable or power adapter.
6. Connect the camera to an AHD DVR or a portable monitor using the video output cable for
viewing the video image while adjusting camera angles. To configure camera settings
using the OSD Menu Joystick.
•Push the Joystick up / down to select
among menu items.
•Push the Joystick left / right to adjust
the level of the selected item.
•Press the Joystick to enter the submenu
or exit the OSD Setup Menu.

EBD930F eZ.HD IR Mini Ball Camera
10
Note: The function button is using to control direction, and also to switch video format and
video output. Please follow the detailed instruction as below to switch the camera to:
Switch between 1080p and 720p (Default, 1080p): Press Upward for 5 Seconds
Switch from HD (1080p / 720p) to 960H: Press Left for 5 Seconds
Switch from 960H to HD (1080p / 720p): Press Right for 5 Seconds
Switch between NTSC and PAL: Press Downward for 5 Seconds
7. Screw back the outer housing and adjust the camera angle simultaneously.
8. Screw the two set screws by using the supplied Hexagon Wrench.

EBD930F eZ.HD IR Mini Ball Camera
11
4. Configuration in the OSD Menu
You can use the Joystick on the rear panel of the camera to configure camera settings in the OSD
menu. For details on the OSD menu structure as below:
No. Main Sub Menu Sub Menu / Function
1 Lens Manual
2 Exposure
Shutter
NTSC: 1/30, 1/60, FLK, 1/240, 1/480, 1/1000, 1/2000, 1/5000, 1/10000,
1/50000, X2, X4, X6, X8, X10, X15, X20, X25, X30, Auto
PAL: 1/25, 1/50, FLK, 1/200, 1/400, 1/1000, 1/2000, 1/5000, 1/10000,
1/50000, X2, X4, X6, X8, X10, X15, X20, X25, X30, Auto
AGC 0 – 15
Sens-up
Off
Auto Sens-up X2, X4
, X6, X8, X10, X15, X20, X25,
X30
Brightness 1-100(40)
D-WDR
Off
On Level 0-8
Auto
Defog
Off
Auto
Pos/Size Position, Size,↑,↓,→,←
Gradation 0-2
Default
3 Backlight
Off
BLC
Level Middle, High, Low
Area Position, Size,↑,↓,→,←
Default
HSBLC
Select Area1, Area2, Area3, Area4
Display Off
On Position, Size,↑,↓,→,←
Black Mask On/Off
Level 0-100
Model All Day
Night AGC Level 0-255
Default
4White
Balance
ATW
AWC→SET

EBD930F eZ.HD IR Mini Ball Camera
12
Indoor
Outdoor
Manual Blue 1-500
Red 0-100
AWB
5
Day &
Night
Ext D→N(Delay) 0-60
N→D(Delay) 0-60
Auto
D→N(AGC) 1-255
D→N(Delay) 0-60
N→D(AGC) 1-255
N→D(Delay) 0-60
Color
B/W
Burst Off/On
IR Smart
Off
On
Level 0-15
Area Position, Size,↑,↓,
→,←
IR PWM 0-100
6 NR 2DNR Middle/Low/Off/High
3DNR Middle/Low/Off/High
7 Special
Cam Title
Off
On 0123456789ABCDEFGHIJKLMNOPQRSTUVWXYZ▶→
←↑↓()ˉ-_▊/=&:~,.
D-effect
Freeze Off/On
Mirror Off, Mirror, V-flip, Rotate
Neg. Image Off/On
Motion
Off
On
Select Area1,Area2,Area3,Area4
Display On Position, Size,↑,↓, →,←
Off
Sensitivity 0-100
Color Green, Blue, White, Red
Trans 1.00,0.75,0.50,
0.25
Alarm
View Type Off, Block, Outline, All
OSD View On/Off
Alarm Out On/Off

EBD930F eZ.HD IR Mini Ball Camera
13
Time 1-15
Default
Privacy
Off
On
Select Area1,Area2,Area3,Area4
Display
Off
Color Position, Size,↑,↓,
→,←
Mosaic Position, Size,↑,↓,
→,←
Inv Position, Size,↑,↓,
→,←
Color White, Black, Red, Blue, CYAN,
Yellow, Green
Trans 1.00,0.75,0.50,
0.25
Default
Language ENG/CHN1/CHN2/GER/FRA/ITA/SPA/POL/RUS/POR/NED/TUR
Defect
Live DPC
Off
On AGC level 0-255
Level 0-100
White DPC
Off
On
Pos/Size Position, Size,↑,↓,
→,←
Start Close the iris then
press
DPC View Off/On
Level 0-60
AGC 0-14
Sens-up x2, x4, x6, x8,x10, x15,
x20, x25, x30
Black DPC
Off
On
Pos/Siz Position, Size,↑,↓,
→,←
Start Press Enter
DPC View Off/On
Level 0-255
RS485 CAM ID 0-255
ID Display Off/On

EBD930F eZ.HD IR Mini Ball Camera
14
Baud Rate 2400,4800,9600,19200 ,38400
8 Adjust
Sharpness
Off
Auto
Level 0-10
Start AGC 0-255
End AGC 0-255
Monitor
CRT
Black Level 0-60
Blue Gain 0-100
Red Gain 0-255
LCD
Gamma
User,0.45,0.50,0.55,0.60,0.65,0.70,0.
75,0.80,0.85,0.90,
0.95,1.00
Blue Gain 0-100
Red Gain 0-100
LSC Off/On
Video. Out PAL/NTSC
9 Exit Save& END /Reset/Not Saved

EBD930F eZ.HD IR Mini Ball Camera
15
5. Specifications
Specifications and designs are subject to change for improving the functionality of this product
without notice.
P/N EBD930F
Pickup Device 1/2.9" Sony 2.24M pixels CMOS
Video Format NTSC and PAL(can be switched via OSD)
Effective Pixels 1920 (H)x1080(V)
Scanning System Progressive Scan
Sensitivity 0 lux with IR on
Electronic Shutter AUTO/Manual (X30~1/50,000)/FLK
Gamma Correction 0.45
Lens Type 3.6mm/6mm Fixed lens
BLC OFF/HSBLC/BLC Selectable
AGC 0~15 Levels
White Balance ATW/AWC-SET/INDOOR/OUTDOOR/MANUAL/AWB
Sync Mode Internal
Day/Night Ext, Auto, Color, B/W
IR LED 24 Units.
IR Distance Up to 15m/50ft. (depending on scene IR reflectivity)
OSD Languages 12-Language
DNR 2DNR/3DNR, Off
DEFOG Off/Auto
D-WDR On/Off
Sens-up Off/On(x30~x2)
Mirror Off, Mirror, V-flip, Rotate
Motion Detection Off/On for 4 selectable zones
Privacy Mask Off/On for 4 selectable zones
Environment IP66 Weather Resistant
Power Source 12VDC
Power Consumption 2.5w max.
Operating Temperature -10°C~50°C / 14°F~122°F
Humidity Less than 80%
Dimensions 93 x 65mm / 3.66” x 2.56”
Weight 400g / 0.88lbs.
Certifications CE / FCC / Rohs

EBD930F eZ.HD IR Mini Ball Camera
EverFocus Electronics Corp.
EverFocus Taiwan:
12F-1, No.79, Sec. 1, Shin-Tai Wu Road,
Hsi-Chih, New Ta ip ei City, Taiwan
TEL: [phone]
FAX: [phone]
www.everfocus.com.tw
[e-mail]
EverFocus Europe - Germany:
Albert-Einstein-Strasse 1, D-46446
Emmerich, Germany
TEL: [phone]
FAX: [phone]
www.everfocus.de
[e-mail]
EverFocus China - Beijing:
Room 609, Technology Trade Building,
Shangdi Information Industry Base,
Haidian District, Beijing 100085, China
TEL: [phone]~39
FAX: [phone]
www.everfocus.com.cn
[e-mail]
EverFocus China - Shenzhen:
4F, No. 2, D4 Building, Wan Yelong
Industrial Park, Tangtou Road, Shiyan,
Baoan, Shenzhen, Guangdong 518101, China
TEL: [phone]
FAX: [phone]
www.everfocus.com.cn
[e-mail]
EverFocus USA - California:
1801 Highland Avenue, Unit A, Duarte, CA 91010,
USA
TEL: [phone]
FAX: [phone]
www.everfocus.com
[e-mail]
EverFocus Japan:
3F Kuramochi, Buildingll 2-2-3 Koto-Bashi,
Sumida-Ku Tokyo, 130-0022, Japan
TEL: [phone]
FAX: [phone]
www.everfocus.co.jp
[e-mail]
Your EverFocus product is designed and
manufactured with high quality materials
and components which can be recycled
and reused.
This symbol means that electrical and
electronic equipment, at their end-of-life,
should be disposed ofseparately from
your household waste.
Please, dispose of this equipment at your
local community waste
collection/recycling centre.
In the European Union there are separate
collection systems for used electrical and
electronic product.
Please, help us to conserve the
environment we live in!
Ihr EverFocus Produkt wurde
entwickelt und hergestellt mit
qualitativ hochwertigen Materialien
und Komponenten, die recycelt und
wieder verwendet werden können.
Dieses Symbol bedeutet, dass
elektrische und elektronische Geräte
am Ende ihrer Nutzungsdauer vom
Hausmüll getrennt entsorgt werden
sollen.
Bitte entsorgen Sie dieses Gerät bei
Ihrer örtlichen kommunalen
Sammelstelle oder im Recycling
Centre.
Helfen Sie uns bitte, die Umwelt zu
erhalten, in der wir leben!