EverFocus H.265 VANGUARD II Series User manual

Value IP Series Network Camera
EZN1250-S & EZN1240-S, H265, IR, WDR
Quick Installation Guide
EZN1240-S
EZN1250-S
Copyright © EverFocus Electronics Corp.
Release Date: March, 2020
All the images including product pictures or screen shots in this document are for example only.
The images may vary depending on the product and software version. Information contained in
this document is subject to change without notice.
EverFocus Taiwan:
2F., No.12, Ln. 270, Sec. 3, Beishen Rd., Shenkeng Dist., New Taipei City 222, Taiwan
TEL: [phone] FAX: [phone] www.everfocus.com.tw

1
1. Physical Description
42
3
EZN1240-S
EZN1250-S
1
5
1
2
3
No.
Item Name
Descriptions
1
Rotate Screw
Loosen the Rotate Screws (on both side) to adjust
the rotating angle.
2
Tilt Screw
Loosen the Tilt Screw to adjust the tilting angle.
3
Pan Screw
Loosen the Pan Screw to adjust the angle.
4
Micro SD Card Slot
This function is not provided.
5
Sunshield
Protect the camera from the direct fun rays.

2
Dimensions
EZN1240-S
75.47mm / 2.97"
75.9mm / 2.99"
148.45mm / 5.8"
EZN1250-S
Ø 83.58mm / 3.29"
82.18mm / 3.24"
241.18mm / 9.5"
Packing List
Please check that there is no missing items in the package before installing.
EZN Series
1. Camera x 1
2. MAC Address Sticker x 2
3. Cable Gland Kit x 1
4. Screw x 3
5. Screw Anchor x 3
6. Hexagon Wrench x 1
7. Quick Installation Guide x 1
8. Installation Sticker x 1

3
Note:
1. Equipment configurations and supplied accessories vary by country. Please
consult your local EverFocus office or agents for more information. Please
also keep the shipping carton for possible future use.
2. Contact the shipper if any items appear to have been damaged in the
shipping process.
Optional Accessory
You can go to the product page on EverFocus’website to check the related
optional accessories. www.everfocus.com.tw
2. Cables
The cables provide connections for network, power, audio input / output and
alarm input / output. A Reset Button Cable is also provided. Please be noted that
microphones / speakers with a (built-in) amplifier and external power supply are
required.
Note: To activate Audio function, the Audio function must be enabled. Please
refer to 5.5.2 Video Streaming in the User’s Manual.
EZN 1240-S
LAN / PoE Cable
Power Cable (12VDC)
EZN 1250-S
Alarm Input / Output
LAN / PoE Cable
12VDC Power Input
Reset Button
Audio Output (White)
Audio Input (Red)

4
Alarm IO PIN Assignment
Note that this function just for EZN1250-S.
1
2
3
4
Alarm In
GND
COM
Alarm Out
Reset Button
Note that this function just for EZN1250-S.
The Reset Button can be used to restore the camera to factory default. When
the camera is powered up, press the Reset Button about 8 seconds to reboot the
camera.
3. Installation
3.1 EZN Series
1. Drill three holes on the surface according to the screw positions on the
Camera Base. Push the supplied 3 Screw Anchors into the holes. Drill another
hole in the middle within the 3 screw holes if you wish to run the wires into
the surface. Screw the camera to surface using the supplied 3 Screws.
Screw Anchor
Screw
Surface
2. Adjust the pan/tilt/rotate angles of the camera by loosen the Pan/Tilt/Rotate
screws using the supplied Hexagon Wrench.

5
Tilt Screw
Pan Screw
Rotate Screws (both sides)
3. Connect the camera to power. You can either connect the camera to a 12VDC
power source or to a PoE switch using the PoE cable.
4. Connect the camera to the network using the supplied Cable Gland Kit.
a. Insert a RJ-45 network cable (without the RJ-45 connector on the one end)
through the supplied Waterproof Ring, Cable Gland, Stopper and Screw
Cap accordingly.
Waterproof Ring Cable Gland Stopper Screw Cap
b. Connect the RJ-45 cable to the LAN/PoE Cable of the camera.
RJ-45 Cable
LAN/PoE Cable
c. Tightly screw the Cable Gland and Screw Cap to the Rugged RJ-45
Connector Cable.
Screw Cap
Cable Gland
d. Crimp the RJ-45 connector onto the RJ-45 network cable. Note that the
wires should be placed into the RJ-45 connector based on the following
order (from left to right).

6
Orange with white stripe
Orange
Green with white stripe
Blue
Blue with white stripe
Green
Brown with white stripe
Brown
5. Now you can access the camera live view. See 4. Accessing the Camera.
4. Accessing the Camera
You can look up the IP address of the IP camera using the IP Utility (IPU)
program, which is included in the software CD.
The default network is DHCP. However, if there is no dynamic IP address
assigned to the device, its IP will switch to 192.168.0.10. By default, the ID is
admin and there is no password. Please input a password for the first-time login.
5. Important Note for Motorized Lens Models
Note that this function just for EZN1250-S.
For motorized lens models, if you find the live image out of
focus, please try the instructions below:
1. Go to the Live page and open the Lens Control panel
(see image on the right).
2. Click the Restore button for the lens to restore to the
default position, and then click the Auto Focus button.
3. If the image is still out of focus, adjust the focus by
clicking the Focus “+”or “-“buttons.
P/N: 4605Z125002003B