EverFocus EQ610x User manual

EQ610x
Indoor Box Camera
600TVL, High Resolution, D-WDR
User’s Manual
* Lens not included.
Copyright © EverFocus Electronics Corp,
Release Date: March, 2013

i
CAUTIONS
1. Do not install the camera near electric or magnetic fields.
2. Never disassemble the camera beyond the recommendations in this manual
nor introduce materials other than those recommended herein.
3. Try to avoid facing the camera toward the sun.
4. Keep the power cable away from water and other liquids and never touch
the power cord with wet hands.
5. Never install the camera in areas exposed to oil, gas or solvents.
6. Do not operate the camera beyond the specified temperature or humidity.
Use the camera at temperatures within -10°C~50°C (14°F~122°F) and
humidity between 20%~ 80%; this device is not rated as submersible.
7. Determine the polarity of the power adapter pigtail before connecting the
camera to the power source. The input power source is 12 VDC /
90-260 VAC~.

EQ610x
1
1. INTRODUCTION
The EverFocus EQ610x box camera features an incredible 600TVL resolution in
full color with a low-light sensitivity of 0.15 lux. Delivered by a high-sensitivity
sensor, the camera also features the added benefits of advanced DSP technology
to enhance image quality. This camera also utilizes technologies like DNR (to
reduce recording file sizes and thus conserve DVR HDD space), Digital Wide
Dynamic Range, Day/Night mode switching, Privacy Masking, Motion Detection,
and much more!
1.1 FEATURES
•600TVL high-resolution CCD sensor.
•High sensitivity, low smear, high anti-blooming and high S/N ratio for
high-performance video.
•Easy-to-use OSD Setup Menu.
•Built-in DNR, D-WDR and easy Day/Night functions.
•Built-in Back Light Compensation (BLC), Auto Electronic Shutter (AES), Auto
Gain Control (AGC) and Auto White Balance (AWB).
•Built-in Motion Detection and Privacy Mask for advanced surveillance
functions.
1.2 PACKAGE CONTENTS
•1 x Camera Unit
•1 x User’s Manual
•1 x Accessory Pack with Screws
•1 x Mounting Bracket
•1 x C-mount Adaptor
•1 x Power Pigtail Cable (only for 12 VDC model)

EQ610x
2
1.3 SPECIFICATIONS
Pickup Device 1/3" High Sensitivity Color CCD
Video Format NTSC, PAL
Picture Elements (H x V) NTSC: 811 x 507
PAL: 795 x 595
Horizontal Resolution 600TVL
Sensitivity 0.15Lux / F1.2
S/N Ratio Over 48dB (AGC off)
Video Output 1.0Vp-p Composite, 75Ω; BNC
Gamma Correction 0.45
Lens Type C/CS Mount (Lens sold separately)
Back Light
Ci
HLC / BLC / OFF
Auto Electronic Shutter 1/60(50) ~ 1/100,000 sec.
Auto Gain Control AUTO (3 Steps)
Auto White Balance ATW1 / ATW2 / AWC / Manual
Sync. Mode Internal
OSD Menu OSD Control (English / Simplified Chinese)
DNR On / Off switch
D-WDR On / Off Switch
Mirror On / Off switch
Motion Detection 4 Detection Zone Blocks
Privacy Mask 8 Zones
Power Source Two types: 90-260 VAC~ or 12 VDC
Power Consumption 12 VDC: 1W max.
90-260 VAC~: 3.1W max.
Operating Temperature -10˚C~50˚C / 14˚F~122˚F
Dimensions (W x D x H) 68 x 56 x 120 mm / 2.6 x 2.2 x 4.7 in
Weight 265 g / 0.58 lbs
Certifications CE / FCC

EQ610x
3
2. CAMERA OVERVIEW
2.1 NAMES AND FUNCTIONS OF PARTS
2.1.1 FRONT PANEL
2.1.2 BRACKET POSITIONS
The bracket in the package can be fitted to the screw holes on the top or bottom
of the camera for either suspending the camera or supporting it.
Light Sensor
Microphone
(Reserved for
Audio-supporting
models)
Top bracket position Bottom bracket position

EQ610x
4
2.1.3 Back Panel
Back Panel:
Side Panel:
1) Left-scroll button
2) Up-scroll button
3) Set button (push to activate OSD)
4) Right-scroll button
5) Down-scroll button
6) Video Output Connector
BNC connector that connects to a 75 Ohm type coaxial cable to feed the
video output of the camera to a color monitor or other video devices.
7) Power Input Terminal
Connects to the appropriate power source.
8) Auto Iris Lens Connector
This connector is used to connect to an auto iris lens via a 4 pin male
connector
Direct Drive
Pin1
Pin2
Pin3
Pin4
Cnt-
Cnt+
Drv+
Drv-
8

EQ610x
5
3 INSTALLATION
1. Unscrew the protection cap from the mouth of the lens mounting.
2. If a C-mount lens is to be used, please screw the C-mount adaptor ring (the
5mm-thick ring in the accessory pack) on to the mouth of the lens mounting.
3. Mount the lens by turning it clockwise on the lens mounting of the
camera.
4. If you use an Auto Iris lens, connect the lens’s cable to the Auto Iris
lens connector on the side of the camera.
5. Place an ND filter in front of the lens, adjust the lens focus until the
best image is obtained.
6. Lock the lens’s focus position by tightening the swivel screw, then
remove the ND filter.
Mount the lens

EQ610x
6
4. CONNECTIONS
Connect the cable from the video output jack of the camera to the monitor’s
input jack.
5. CAMERA SETUP OPERATIONS
This camera utilizes an On Screen Display (OSD) user setup menu.
5.1 SETUP BUTTONS
To set items on the user setup menu, use the following buttons on the back
panel.
EXT.
SENSOR
The cursor direction buttons and the SET/Enter button
Set (Enter) button

EQ610x
7
①ENTER
Press this button (by pressing straight down on the stick) to display the
OSD’s main menu on the monitor that you have connected directly or
indirectly to the camera’s video connector. Also press this button to
confirm changes and to open the submenus when they’re available and
selected. (Menu items with a “<┘” symbol at the end contain submenus.
For adjusting submenu items, select the desired menu item with the 
and buttons and press the ENTER button to open the desired
submenu. Use the and buttons to toggle between value options.)
②R (RIGHT)
Press this button (by pressing the control stick to the right) to move the
on-screen cursor to the right to select items or to adjust the
level/intensity of a selected function. The level/intensity increases when
this button is pressed.
③L (LEFT)
Press this button (by pressing the control stick to the left) to move the
cursor to the left to select items or to adjust the level/intensity of a
selected function. The level/intensity decreases when this button is
pressed.
④D (DOWN)
Press this button (by pressing the control stick in the “down” direction)
to scroll the on-screen cursor downwards between menu items.
⑤U (UP)
Press this button (by pressing the control stick in the “up” direction) to
scroll the on-screen cursor upwards between menu items.