EverFocus EAN7221 User manual

Star Light Box Network Camera
EAN7221/7260/7360
Ultra Low Light Network Camera
Quick Installation Guide
** Lens not included.
Copyright © EverFocus Electronics Corp.
Release Date: March, 2016

EAN7221/7260/7360
1
1. Physical Description
267
1
12
10 11 13
9
8
45
14
3
No.
Item Name
Descriptions
1 Auto Iris Lens Connector Plug the iris control cable to the connector.
2 Microphone One built-in microphone.
3 Light Sensor Detects lights.
4 Ethernet / PoE Connects to a 10BASE-T / 100BASE-TX Ethernet or PoE.
5 Power LED After powering the camera, the power LED will be lit in red.
6 DC 12V Port Connects to 12VDC power.
7 Alarm Connects to I/O devices (see I/O Terminal Block for more details
later).
8 Audio In Connects to microphones (In) / Speakers (Out). Note that the
audio input / output features a line 3.5mm jack (TRS). Be sure
to prepare microphones / speakers with TRS connector (see TRS
Connector image below). Also, microphones / speakers with a
(built-in) amplifier and external power supply are required.
9 Audio Out
10 AC 24V Port Connects to 24VAC~ power.
11 Micro SD / SDHC Card Slot Insert a micro SD / SDHC card to store recording data.
12 Video Out Connects to a portable monitor using the supplied BNC cable
for testing the camera view during initial installation.
13 USB USB slot is currently reserved.
14 Reset Button Press and hold the button for 6 seconds to reset all
configurations to factory default.

EAN7221/7260/7360
2
TRS Connector
Left Channel (Tip)
Right Channel (Ring)
Ground (Sleeve)
To activate the Audio function, the Enable Audio must be
checked. You can also select Audio Input from line-in or mic-in.
See 7.2.1 Streaming and Audio in the User’s Manual in the
software CD.
System Requirements
Before installing, please check that your computer meets the following system requirements.
Operating System Windows 7 (32 and 64-bit) or above
CPU Intel Core i5 CPU @ 2.0GHz (or equivalent AMD) or higher
(Intel Core i7 CPU @ 3.4GHz recommended)
Graphic Card 512MB RAM graphic cards (or equivalent on-board graphic cards)
RAM
•
2GB or more (8GB recommended)
•Additional HD space depends on required local storage of video files,
100 Mbps network card.
Software
•
DirectX 9.0c
•Internet Explorer 9 and later, Firefox 4.0-9.0, Chrome (Windows
version 44 and earlier)
Dimensions
118.10mm/4.65" 68.30mm/2.69"
56.40mm/2.22"

EAN7221/7260/7360
3
I/O Terminal Block
The I/O terminal block, located on the rear panel of the camera, can be used to develop application
for alarm in / out and RS-485 devices.
1 2 3 4 5 6
Pin Assignment
No. Function No. Function No. Function
1 Alarm COM (-) 3 Alarm Input (+) 5 RS-485+
2 Alarm Output (+) 4 Digital GND (-) 6 RS-485-
Packing List
• EAN Series Camera (lens not included) x 1
• Software CD x 1
• Quick Installation Guide x 1
• Tool Packet x 1 (contains the following items)
-C-Mount Lens Adapter - Video Test-Out Cable (BNC)
-Hexagon Wrench - Power Pigtail Cable
-2 MAC Address Stickers -¼-20 UNC Thread Mounting Bracket and 2
Screws
-Two-Pin Terminal Block (24VAC~)
Note:
1. Equipment configurations and supplied accessories vary by country. Please consult your local
EverFocus office or agents for more information. Please also keep the shipping carton for
possible future use.
2. Contact the shipper if any items appear to have been damaged in the shipping process.

EAN7221/7260/7360
4
Optional Accessories
You can use the optional accessories to expand the capabilities and versatility of the camera. Please
contact your dealer for more information.
•EFV-M1600DCIR
1/2.5" F=1.67mm, DC IRIS F/1.8, IR CS Mount (5 MegaPixel)
•EFV-M0940DCIR
1/2”, MP Lens, F=9-40mm, DC IRIS, CS mount (5 MegaPixel)
•EFV-M1803IR
1/2" 1.8-3mm, Manual IRIS F/1.8, IR CS Mount (5
MegaPixel)
•EFV-M1803DCIR
1/2" 1.8-3mm, DC IRIS F/1.8, IR CS Mount (5 MegaPixel)
•BA-EZN
Bracket for Box Type Cameras
Max. Load: 990g / 2.18lb
Dimensions: 137 x 105.5 x 105mm / 5.39" x 4.15" x 4.13"
Aluminum
•IP Sidekick - ESK1000
Using it for installation, you do not need to pre-configure
the IP address or to use an additional monitor to check and
adjust all the IP cameras. The product can assign an IP
address to the camera, then you can connect and check the
camera live view using EverFocus mobile App EF Sidekick.
For details about IP Sidekick, please refer to the IP Sidekick –
ESK1000 User’s Manual.

EAN7221/7260/7360
5
•EverFocus 5 / 8 / 16 / 24 Ports
PoE Switch
5 Ports: ES0501-40
8 Ports: ES0812-31 / ES0802-41
16 Ports: ES1625-31 / ES1645-51
24 Ports: ES2426-31 / ES2446-51 / ES2448-62
2. Installation
This installation guide provides the basic instructions on installing an EAN box IP camera.
Lens Installation and Adjustment
You can install either a CS-Mount or a C-Mount lens into the camera. It is recommended to use a
lens with aperture ratio of F/1.2 or smaller. Please refer to the following reference steps.
C-Mount Lens Adapter
DC Auto Iris Lens Connector
Focus Screw
Zoom Screw
C-Mount Lens:
1. Remove the cover cap from the camera body.
2. Install the lens into the camera body using the
supplied C-mount lens adapter.
3. Adjust the lens using the Focus / Zoom Screws.
Note: Installing a C-mount lens without the C-mount lens adapter may damage the camera sensor.
If you are using a DC Auto Iris lens:
1. Remove the cover cap from the camera body.
2. Install the lens into the camera body.
3. Connect the DC cable to the DC Auto Iris Lens Connector.

EAN7221/7260/7360
6
4. When making final focus adjustment, place the ND filter (not supplied in the package) in front
of the lens to force the lens iris to open, and then adjust the lens using the Focus / Zoom
Screws.
5. Lock the Focus Screw and then remove the ND filter.
CS-Mount Lens:
1. Remove the cover cap from the camera body.
2. Install the lens into the camera body.
3. Adjust the lens using the Focus / Zoom crews.
Top / Bottom-Mount
You can use the supplied mounting bracket and screw it on the top of the camera body to suspend
the camera, or on the bottom of the camera body to support the camera.
Top Mount
Bottom Mount

EAN7221/7260/7360
7
Basic Connection
1
2
4
4
3
5
2
1. Use a standard network cable to connect the camera to the network.
2. Connect the camera to power using one of the following methods:
•Connect the camera to a 12VDC power source using the supplied Power Pigtail Cable.
•Connect the camera to a 24VAC~ power source using the supplied Two-Pin Terminal Block.
•Using the PoE function and the power will be provided over the network cable.
3. Optionally connect the camera to a monitor using the supplied video Test-Out BNC Cable.
4. Optionally connect the camera to the speakers and microphones. Note that the audio input /
output features a line 3.5mm jack (TRS). Be sure to prepare speakers / microphones with TRS
connector. Also, speakers and microphones with a (built-in) amplifier and external power supply
are required. You can also use the built-in Microphone on the front panel of the camera (See
Physical Description for more details).
5. Optionally connect the camera to the input / output devices.
After powering the camera, the power LED will be lit in red and you can access the live view and
adjust the image clarity.

EAN7221/7260/7360
8
3. Accessing the User Interface
You can look up the IP address and access the Web interface of the IP camera using the IP Utility
(IPU) program, which is included in the software CD. The IP Utility can also be downloaded from
EverFocus’ Website: http://www.everfocus.com.tw/HQ/Support/DownloadCenter_p1.aspx
(Support > Download Center > Keyword Search: IP Utility). Please connect the IP camera on the
same LAN of your computer.
1. Save IP Utility Setup .exe in your computer. Double click the .exe file and follow the
on-screen instructions to install the IP Utility.
2. Click the Finish button, the IP Utility will be automatically launched to search the IP devices
connected on the same LAN.
3. To access the Live View window, double click the IP address of the desired device, the login
window pops up. Type the user ID and password to log in. By default, the user ID is user1
and the password is 11111111.

EAN7221/7260/7360
9
4. If you log in for the first time, follow the on-screen instructions to update the latest Plugin
version (ePlayer). After reloading the webpage, the login window pops up again. Type the
user ID and password to log in again. By default, the user ID is user1 and the password is
11111111.
5. Now you will be able to see the remote live page.
Note:
1. The “Download ePlayer Instruction” page will only be prompted for the first time login in
order to update the system to the latest Plugin version.
2. If the Error window appears, please be sure to close ALL the Web browser windows first
and then click Retry. When the Completing the ePlayer Setup Wizard window shows up,
click Finish. Then, you can open a new browser again to access the camera’s remote Web
interface.