EverFocus EHA1281 eZ.HD Series User manual

EHA1281 eZ.HD Series
1080p Dual Power FHD IP66 IR Dome Camera
User’s Manual
Copyright © EverFocus Electronics Corp.
Release Date: November, 2022
All the images including product pictures or screen shots in this document are for example only.
The images may vary depending on the product and software version. Information contained
in this document is subject to change without notice.
EverFocus Taiwan:
2F., No.12, Ln. 270, Sec. 3, Beishen Rd., Shenkeng Dist., New Taipei City 222, Taiwan
TEL: [phone] FAX: [phone] www.everfocus.com.tw

1. Introduction
Equipped with a 1080p Sony CMOS sensor, the EHA1281 deliver 1080p full HD
image quality. The model provides 2.8-12mm lens with ICR. Featured with Digital
Wide Dynamic Range (D-WDR), the camera can provide clear images even under
backlight circumstances where intensity of illumination can vary excessively. The
EHA1281 supports dual power (12VDC / 24VAC) and supports both NTSC and PAL
scanning systems.
1.1 Packing List
Camera x 1
Mounting Sticker x 1
L-Type Wrench x 1
Screw & Screw Anchor x 4
Desiccant Bag x 1
User Manual x 1
1.2 Features
1080p Sony CMOS sensor, delivering amazing high sensitivity
Varifocal 2.8-12mm with ICR to capture the desired field of view
Extended IR range of up to 30m / 98ft. with 30 LEDs (depends on scene IR
reflectivity)
D-WDR to improve the visibility under high contrast scene
3-Axis rotation design allows wall or ceiling mounting
IP66-rated with metal housing
Supports dual power (12VDC / 24VAC)
Supports UTC function: Control camera OSD settings directly from DVR end
1.3 Dimensions

2
1.4 Optional Accessory
Type
Wall Mount Bracket
Junction Box
Image
Model
Name
BA-EB45-A
BA-EB18-A
Color
White / Metal
White / Metal
Size
(WxDxH)
208L*120mm
Φ136mm
Weight
285g
215g
Type
Ceiling Mount Bracket
Image
Model
Name
BA-EB3A-A
BA-EB3B-A
Color
White / Metal
White / Metal
Size
(WxDxH)
Φ135.7mm
Φ135.7mm
Weight
155g
346g
1.5 Cable Description
12VDC / 24VAC Power Cable
Video Output Cable (BNC, 75Ohm)
2. Installation
1. Stick the supplied Mounting Sticker to the surface to mark the 4 screw
positions. Drill four holes on the surface and insert the supplied 4 Screw
Anchors into the screw holes. If you want to run the cable through the
surface, drill a hole within the 4 screw area.

3
2. To mount the camera to the surface:
a. Remove the Base Plate from the camera. To do so, 1) Remove the Fix
Screw 2) Slightly push the Base Plate backward from the Fix Screw side
and then pull out the Base Plate. Screw the Base Plate to the surface using
the supplied 4 Screws.
b. Open the Camera Cover to remove the old desiccant bag from the Camera
Body and stick the supplied Desiccant Bag inside the Camera Body. It’s
highly recommended to replace the desiccant bag every time when you
open the Camera Cover.
c. For the first time installation, check whether the camera is properly
focused. If not, you can optionally adjust camera zoom and focus by
adjusting the Zoom Screw or Focus Screw using a slotted screwdriver.
Note: Please screw back the Camera
Cover immediately in case of reducing
the absorption capacity of the desiccant
bag inside the camera body.

4
d. Attach the Camera Body to the Base Plate. Screw back the Fix Screw.
3. Connect the Power Cable to a 12VDCpower source. Connect the Video
Output Cable to a monitor or DVR.
4. You can use the Joystick on the cable to configure camera OSD settings or
switch to different video formats. Remove the Protection Cap from the
Joystick before using it.
UP
DN
Switching Video Format:
Push the joystick up for 5 sec. to switch to
resolution1080p/720p.
Push the joystick right for 5 sec. to switch to AHD.
Push the joystick down for 5 sec. to switch to
NTSC/PAL.
Push the joystick left for 5 sec. to switch to CVBS.
Push the joystick center to enter main menu.
Configuring OSD Settings:
Push the Joystick up / down to select among
menu items.
Push the Joystick left / right to adjust the level of
the selected item.
Press the Joystick to enter the sub-menu or exit
the OSD Setup Menu.
5. You can optionally adjust the camera angles. To do so, unscrew the 4 cover
screws using the supplied L-Type Wrench and then remove the cover. Adjust
the camera angles (Tilt: 90°, Pan: 180°, Rotate: 90°). After adjusting camera
angles, screw back the camera cover.

5
3. Configuration in the OSD Menu
You can configure camera settings in the OSD menu from DVR end.
No
Main
Sub
Menu
Sub Menu / Function
1
Lens
Manual / DC
2
Exposure
Brightness
0-100
Shutter
Auto
Manual
Spee
d
1/25,1/50, 1/200, 1/400, 1/1000,
1/2000, 1/5000, 1/10000
Flicker
Sens-Up
Off, x2, x4, x8, x10, x15,x20,x25,x30
AGC
0-15
Sens-up
Auto/Off
Brightness
0-100
D-WDR
Off/On
Level: 0-8 ; Return: Set
Defog
Off/Auto
Pos/Size/ Gradation:0-2/ Default/Return
Return
Set: Save/End
3
Backlight
Off
BLC
Mode
Night Only / All Day
Level
Middle
Area
Pos/Size
Default
Return
Set
4
White Bal
ATW
AWC
Indoor /Outdoor
AWB
Manual
Blue
0-100
Red
0-100
Reture
Set
5
Day&Night
Auto
Mode
Auto
Color
B&W
Burst
Off/on
IR
Smart
Off
On
Level:0-15
Area:0-2
Return: Set
Return
Set
Exter
n
D-N
0-60
N-D
0-60
Return
set
6
N R
2 DNR
Off/Low/Middle/High
3 DNR
Off/Low/Middle/High
Return
Set
Auto
D-N (AGC)
0-255
N-D(Delay)
0-60
N-D (AGC)
0-255
N-D (Delay)
0-60
Return
Set

6
Special
Cam Title
Off/ On
7
D-effect
Freeze
On/Off
Mirror
Off
On
V-flip
Rotate
Neg Image
On/Off
Return
Set
Motion
Off
On
Select
Area: 1-4
Display
On/Off
Sensitivity
0-100
Color
Red/Green/Blue/White
Trans
0, 0.25,0.75,1
Alarm
View
Type
Off/Block/Outline/All
OSD View
On/Off
Alarm
Out
On/Off
Time
0-15
Return
Set
Default
On/Off
Return
Set
Privacy
Off
On
Select
Area 1-4
Display
INV/MOSAIC/COLOR
Color
White/Black/Red/Blue/Yellow/
Green/Cyan/User
Trans
0,0.25,0.75,1
Default
On/Off
Return
Set
Language
ENG/CHN1/CHN2/GER/FRA/POL/RUS/POR/NED/TUR
Defect
Live DPC
Off
On
AGC
0-255
Level
0-255
Return
Set
White DPC
Black DPC
POS/Size
Start
DPC/Vie
w
On/Off
Level
0-100
Return
Set
Return
Set
RS485
Cam ID
0-255
ID Display
On/Off
Baud rate
38400/2400/4800/9600/19200
Return
Set
Return
Set

7
8
Adjust
Sharpness
Auto
Level
0-10
Start AGC
0-255
ENR AGC
0-255
Return
Set
Monitor
LSC
On/Off
Comet
On / Off
Output
Mode
Monitor Out
AHD/THD/CHD/CVBS
Output Size
1080P/720P
Video Out
NTSC/PAL
Return
Set
Return

8
EverFocus Electronics Corp.
EverFocus Taiwan:
2F., No.12, Ln. 270, Sec. 3, Beishen Rd., Shenkeng
Dist., New Taipei City 222, Taiwan TEL: [phone]
2338 FAX: [phone]
www.everfocus.com.tw
[email protected]
EverFocus China - Shenzhen:
2F, Building A, Area A, Longquan Science and
Technology Park,Tongfuyu Phase II, Henglang
Community, Dalang Street, Longhua,Shenzhen
518109, Guangdong, China TEL: [phone]
1313 FAX: [phone]
www.everfocus.com.tw
[email protected]m.tw
EverFocus USA - California:
324 W Blueridge Avenue, Orange, CA 92865, USA
TEL: [phone] FAX: [phone]
www.everfocus.com
[email protected]
EverFocus Japan - Tokyo:
7-6-4-101 Takashimadaira, Itabashi-ku, Tokyo
175-0082, Japan TEL: [phone] FAX: +81
(3) 4363-2790
www.everfocus.co.jp [email protected]
Your EverFocus product is designed
and manufactured with high quality
materials and components which can
be recycled and reused. This symbol
means that electrical and electronic
equipment, at their end-of-life, should
be disposed of separately from your
household waste. Please, dispose of
this equipment at your local
community waste collection/recycling
centre. In the European Union there
are separate collection systems for
used electrical and electronic product.
Please, help us to conserve the
environment we live in!
Ihr EverFocus Produkt wurde
entwickelt und hergestellt mit
qualitativ hochwertigen Materialien
und Komponenten, die recycelt und
wieder verwendet werden können.
Dieses Symbol bedeutet, dass
elektrische und elektronische Geräte
am Ende ihrer Nutzungsdauer vom
Hausmüll getrennt entsorgt werden
sollen. Bitte entsorgen Sie dieses Gerät
bei Ihrer örtlichen kommunalen
Sammelstelle oder im Recycling Centre.
Helfen Sie uns bitte, die Umwelt zu
erhalten, in der wir leben!