EverFocus WDII EQ600 User manual

INSTRUCTION MANUAL
1/3” W-Dynamic High Resolution Color Camera
Version1.0
About this manual
Before installing and using this camera, please read this manual carefully.
Be sure to keep it handy for later reference.
EQ600 WDII

Safety Warning
1. Read manual carefully before installing the unit.
Please read this manual first for correct installation and operation.
2. Never install the camera on a ceiling that cannot hold its weight
The product may fall down to cause damages.
3. Do not install the camera near electric or magnetic fields.
Installed the camera away from TV, radio transmitter, magnet, electric motor, transformer, audio
speakers because the magnetic fields generate from above devices will distort the video image.
4. Always stop using when the product emits smoke or abnormal heat
5. Never disassemble the camera nor put impurities in it
Disassembly or impurities may result in trouble or fire.
6. Never face the camera toward the sun.
Direct sunlight or severe ray may cause fatal damage to sensor and internal circuit.
7. Keep the power cord away from wet and never touch the power cord with wet hands.
Touching the wet power cord with hands or touching the power cord with wet hands may result in
electric shock.
8. Never install the camera in areas exposed to water, oil or gas.
The water, oil or gas may result in failure, electric shock or file.
9. Cleaning
Do not touch the surface of sensor by hand directly. Use a soft cloth to remove the dirt from the
camera body. Use lens tissue or a cotton tipped applicator and ethanol to clean the sensor and the
camera lens.
10. Do not operate the camera beyond the specified temperature, humidity or power source
ratings.
Use the camera at temperatures within 0℃
℃℃
℃~ 40℃
℃℃
℃and humidity below 90%. The input power
source is DC12V/AC24V.
Notice:The information in this manual was current when published. The manufacturer reserves the
right to revise and improve its products. All specifications are therefore subject to change without notice.

1
Table of Contents
1. Product Overview……….………………..……………..………………………….…….…2
1.1 Main Features.…..…………..………………………………………………..…………2
1.2 Content List………………………………………………………………………………2
1.3 Specifications……………..……….……………………………………………………..3
2. Back Panel Connections………………………….………………………….…………….4
3. Operation………………………………………………………..………………..……..…5~6
3.1 Setup Buttons…...………………………………………………………………..……...5
3.2 Display/Close the user setup menu screen…..………………………………………6
4. Main Menu Flow……..…………..………..…………………………………………………7
5. Preset Mode……………..……………………………..…….………………………………8~9
5.1 User Setup Menu Flow….…………………………………………………………..….8
5.2 User Setup……………………………………………………………………………….9
6. Camera ID………………………………………………………..………………………10~11
6.1 Camera ID……………………………………………………………………………….10
6.2 ID Position……………………………………………………………………………….11
6.3 ID Color ………………………………………………………………………………….11
6.4 ID Background…………………………………………………………………………..11
7. Advanced Setup…………………………..…………..…….…………………………12~13
7.1 Auto IRIS…………………………………………………………………………….…..12
7.2 White Balance……………………………………………………………………..……12
7.3 LineLock…………………………………………………………………………………13
7.4 Viewing………………………………..………..…………………………………..14
8. Save/Restore……………………………………………………………………………..…15
Appendix-A…Camera ID Character patterns……………………………………….……..17
Appendix-B…Factory Settings Chart……………………………………..………….…….18

2
Product Overview
1. Product Overview
By utilizing Digital Pixel SystemTM (DPS) sensor technology, the new EQ600WDII dramatically
improves the performance of surveillance camera in extreme lighting conditions. Where traditional
CCD cameras have difficulty processing images in strong backlighting, the EQ600WDII processes
each pixel independently, correcting for the variations and providing the best possible image under
the lighting conditions.
1.1Main Features
 1/3” Color DPS sensor
 High resolution: Over 480 TV Lines/1.0lux and low speed shutter up to 32x
 Day/Night function
 OSD function control
 With programmable camera ID up to 12 characters
 Compact stylish design for discrete observation
 Free S/W for remote configuration through RS232 via PC
 Image flip: Horizontal reverse
1.2Content List
 1/3” W-Dynamic High Resolution Color Camera unit
 User’s manual
 Mini Din male connector cable for S-Video / RS-232

3
Specifications
1.3 Specifications
Pickup Device 1/3” Color DPS sensor
Picture Element 720(H) ×540(V)
Horizontal Resolution >480 TV lines
Sensitivity 1.0 Lux/ F=1.2 (50IRE color)
Low Speed shutter Up to 32x(2,4,8,16,32)
S/N Ratio >48dB
Auto exposure: YES
Auto White Balance Yes, 2500K ~9500K
Back light compensation YES
Auto IRIS YES
Video Outputs 1.0Vp-p composite S-Video(Y/C output)
Auto Gain Control Yes
Day/Night function ON/OFF
Dynamic range 95dB typical, 120dB max
Synchronization Internal or Line Lock (AC input required)
Image Flip Yes, Horizontal reverse
Video Output: 1 Vp-p / 75 ohm composite, S-Video (Y/C output)
Imaging System NTSC/ PAL
On Screen Display Yes
Power Source AC24V / DC12V
Operating Temperature 0℃
℃℃
℃~ 40℃
℃℃
℃
Power Consumption 7W max.
Dimensions (mm) 56 (W) x 68 (H) x101 (D)
Lens mount C/CS mount, DD Drive

4
Back Panel Connections
2. Back panel connections
(1)S-Video / RS-232 port:
Connect Mini Din Male Connector to S-Video / RS-232 port for better video output quality or
communication. Please refer to the pin assignment of the S-Video/ RS-232 port as below:
(2)AC24V/DC12V Compatible Input Terminal:
This power terminal is for connecting theAC24V/DC12V power supply cord
(3)Video Output Connector: Connect the video output of the camera to a color monitor or other
video devices through a 75 Ohm type coaxial cable with BNC female connector at backside of
the camera.
(4) Tact switcher for left cursor
(5) Tact switcher for down cursor
(6) Tact switcher for right cursor
(7) Tact switcher for up cursor
(8) Tact switcher for on-screen setting menu
(9) Auto Iris Lens Connector
This connector is used to connect with the auto iris lens by a 4 pin male connector
Pin 1 Pin 2 Pin 3 Pin 4
Video Drive +12V GND VD-IRIS GND
DirectDrive Cnt- Cnt+ Drv+ Drv-
(4)
(1)
(2)
(3)
(5)
(6)
(7)
(8)
Y GND
GND
Y
RX
5V
TX
C GND
C
(9)

5
Operation
3.Camera Setup Operations
This camera utilizes an On Screen Display (OSD) user setup menu.
3.1 Setup Buttons: To set items on the user setup menu, use the following buttons on the back
panel.
①
①①
① Up Button: This button is used to move the cursor upwards. Use this button to select an
item or adjust the parameters.
②
②②
② Down Button: This button is used to move the cursor downwards. Use this button to select
an item or adjust the parameters.
③
③③
③ Right Button: This button is used to move the cursor to the right. Use this button to select
or adjust the parameters of the select item. The parameter changes each
time as this button is pressed.
④
④④
④ Left Button: This button is used to move the cursor to the left. Use this button to select or
adjust the parameters of the select item. The parameter changes each time
as this button is pressed.
⑤
⑤⑤
⑤ Set Button: This button is used to set the determined parameters. If the item has its own
setting menu, press this button to display the setting menu.
①
①①
①Up Button
③
③③
③Right Button
②
②②
②Down Button
④
④④
④Left Button
⑤
⑤⑤
⑤Set Button

6
Operation
3.2 Display/Close the user setup menu screen
I. Press the SET button for 2 second
The menu screen will appear on the monitor as the block shown above.
II. Using the cursor button
Use the cursor button or to move the cursor up or down. Use the cursor button or
to adjust the mode or parameter of settings. The select item will be highlighted with a
gray color bar.
III. Switch to sub-menu screens
When the item with sub-menu is selected (highlighted), press the SET button to switch to
the sub-menu for further settings. Please refer to the figure below.
Note: For those select items with “…” sign in the end, they have the sub-menu for further
settings.
IV. Return to previous page
After setting, use the cursor buttons to select PREVIOUS PAGE, then press the SET
button.
V. Close the menu screen
To close the menu screen, use the cursor button to select EXIT MENU and press the
SET button. Or press the SET button for 1 sec.
SET
Butto
n
The Cursor Buttons & the SET Button
Sub-Menu
Main Menu
EWD600 MAIN MENU
PRESET MODE INDOOR…
CAMERAID OFF
> ADVANCED SETUP…
SAVE/RESTORE…
EXIT MENU
EWD600 MAIN MENU
> PRESETMODE INDOOR…
CAMERAID OFF
ADVANCED SETUP …
SAVE/RESTORE…
EXIT MENU
ADVANCED SETUP
> AUTO IRIS…
WHITE BALANCE…
LINELOCK…
VIEWING…
PREVIOUS PAGE
Highlighted

7
MENU Flow
4. MAIN MENU FLOW
ADVANCED SETUP
> AUTO IRIS…
WHITE BALANCE…
LINELOCK…
VIEWING…
PREVIOUS PAGE
EWD600 MAIN MENU
>PRESET MODE… <INDOOR…>
<OUTDOOR…>
<FLUOR. ….>
<BACKLIGHT…>
<USER…>
EWD600 MAIN MENU
>CAMERA ID… < OFF>
<ON…>
SAVE/RESTORE
> RESTORE USER SETTINGS..
SAVE USER SETTINGS..
RESTORE FACTORY SETTINGS..
RESET CAMERA..
MENUREV. 0.1
PREVIOUS PAGE…
EWD600 MAIN MENU
>PRESETMODE INDOOR…
CAMERAID OFF
ADVANCED SETUP…
SAVE/RESTORE…
EXIT MENU

8
MENU
5. PRESET MODE
I. Select the suitable settings, such as
INDOOR, OUTDOOR, FLUOR. or
BACKLIGHT based on the installation
environment.
II. Press the SET button to enter USER
SETUP menu for adjusting the
parameters.
III. The parameters will be stored as USER
automatically after changed.
5.1 USER SETUP Menu Flow
USERSETUP
>CAMERAVIEW SHADOW
SLOW SHUTTER OFF
WDRMODE AUTO…
METER MODE NORMAL…
PREVIOUS PAGE
USERSETUP
>CAMERA VIEW <SHADOW>
<HIGHLIGHT>
USERSETUP
>SLOW SHUTTER <OFF>
<ON>
AUTO DYNAMIC RANGE
>BIAS +++++++++
–36 6 36
LIMIT +++++++++
0 24 36
PREVIOUS PAGE…
NORMAL METER PRESETS
>PRESETS <FULLSCREEN..>
<CENTER>
<LOWER1/3…>
<USER…>
<USER ZONE ADJUST>
PREVIOUS PAGE…
EWD600 MAIN MENU
>PRESET MODE <INDOOR…>
<OUTDOOR…>
<FLUOR. ….>
<BACKLIGHT…>
<USER…>
MANUAL DYNAMIC RANGE
>RANGE +++++++++
0 24 36
PREVIOUS PAGE…
USERSETUP
>WDR MODE <AUTO…>
<MANUAL…>
USERSETUP
>METER MODE <NORMAL…>
<BACKLIGHT…>
BACKLIGHT METER PRESETS
>PRESETS <FULLSCREEN..>
<CENTER>
<LOWER1/3…>
<USER…>
<USERBL-ZONE ADJUST>
PREVIOUS PAGE…
SLOW SHUTTER SETUP
>SHUTTERLIMIT 8X
SS PROTERTY COLOR
B/W
SS THRESHOLD +++++++++
0 28 42