EverSewn Loft-2 Manual

EverSewn Loft - 2
SET-UP INSTRUCTIONS
LOFT
Before you get started:
• Two people are necessary for assembly.
• Call 1-844-EVERSEW (1-844-383-7739) or [e-mail] for information or assistance.
• Your Loft consists of 5 large boxes and 1 small box.
• Organize hardware into piles.
Tools needed:
+ -
version 4
Disclaimer: For home use only. Brewer Sewing Supplies is not responsible for injuries associated with the Loft system and assembly.

Side board (2x) Fixed board (1x) Moveable board (1x) Back panel (1x)
Table Top (1x) Machine Cover (1x) Spacer (1x) Leg (1x)
Included Parts
LOFT
(1) (2) (3) (4)
(5) (6)
(7)
(8)
Long Cam Pin
(4x)
(B1)
Dowel (8x)
(A)
Cam Lock
(20x)
(C)
Wood Screw
(8x)
(E4)
Handle (6x)
(H)
Drawers (1x)
(9)
Steel Column
(4x)
(D)
Silver Screw
(12x)
(G)
Adhesive Cam
Cover (20x)
(P)
Gold Screw
(2x)
(G2)
Cam Pin (16x)
(B)
Balance Leg
(4x)
(F)
Tee Nut (4x)
(P)
Silver Screw
(4x)
(K1)
Silver Screw
(4x)
(K2)
Nut (4x)
(X)
Handle (3x)
(G)

Set-Up
LOFT
Screw in balance legs (F) to underside
of drawers (9).
Attach Cam Pins (B) and Steel
Columns (D) to Drawers and Leg (8).
Place Back Panel (4) into Drawers and Leg.
Tighten left side cam locks (C) only.
Assemble machine holding bed with the side
boards (1) and fixed board (2).
Hammer tee nuts (P) into fixed board (2).
Attach bed to back panel (4) using the cam locks
(C).
Attention: If table is used with sewing machine
30lbs+, add gorilla glue, or similar, on both ends
to secure dowels. Glue not included.
1
2
3
(B)
(B)
(B)
(B)
(D)
(D)
(D)
(D)
(4)
(P)
Note: Do not tighten
back panel to
drawers until step 6
is completed!
Note: If necessary,
carefully slide out
drawers to assemble
holding bed.
(9)
(8)

Set-Up
LOFT
Line up the holes and place spacer (7) on
top of leg.
Insert big gold screws (G2) through
underside of leg (8) and tape into place
until table top is attached.
Depending on size of machine screw K1
or K2 screws into tee nuts (P). Make sure
all screws are level. Add nuts (X) to
secure position of screw. Set moveable
board on top.
Adjust board height by lowering
or raising screws.
Remove one or two drawers. Use
black wood screws (E4) to attach
drawer to table top.
Once complete put drawers back and
attach handles (G).
Place machine cover (6).
4
6
5
(K1/K2)
(E4)
(X)
(G2)
32
1. Place table top. 2. In order to tighten all cam
locks (C), slide table top and
leg to the left.
3. Slide table top and leg
back into place and secure
with cam locks (C).
(G)
(9)
(8)
(4)
(2)
(6)