Lee & Plumpton Duty User manual

No. 113 A/1882 Revision A 10/10/2018 1
www.leeandplumpton.co.uk
ASSEMBLY INSTRUCTIONS
RANGE Duty, Rectangular and Wave, with and without Modesty.
REF: 1400mm, 1600mm, 1800mm – Left and Right Hand.
Read this leaet before
assembly
2 People
Required
COMPONENT PARTS
TOOLS REQUIRED BEFORE YOU BEGIN...
• Check you have all the tools and components required
• Keep children and animals away from small parts
• Ensure you have adequate space
• Assemble product on a at, clean surface
• Apply manual handling guidelines when building this item
• Pozi head screwdriver
• 4mm Allen Key
Item 1
Top Panel
Qty 1
NP4/990
Item 2 *
Modesty Panel
Qty 1
NP4/939
Item 4
GoalPost Frame
Qty 1
NP4/975
Item 3
GoalPost Frame
Qty 1
NP4/937
Item 6 & 7
Cable Port
Qty 4
A/0525 & A 0527
Item 8
Adjustable Foot
Qty 4
M/0655
Item 9
Expander Plate
Qty 4
A/1164
Item 10 *
Modesty Spacer
Qty 8
R/0071
Item 11
Top Panel Spacer
Qty 1
R/0072
Item 12 *
Minix Bolt Chipfast
(Long)
Qty 4
F/0508
Item 13 *
Minix Bolt M6
Qty 4
F/0433
Item 14 *
Minix Cam
Qty 8
F/0434
Item 15 *
Cam Cover
Qty 8
F/0436, F/0446, F/0545,
F/0575, F/0576, F/0577
Item 16
M6x70mm Flat Hd
Skt Bzp
Qty 1
F/0471
Item 17
Rail Screw
Qty 8
F/0587
Item 18
Grub Screws M8
Qty 8
F/0637
Item 19
5mm Hole Plugs
Qty 4
A/0518, A/0763,
F/0546
* Desk with Modesty Panel only.
Item 5
Rail
Qty 2
R.0098
Wave with Modesty shown.

No. 113 A/1882 Revision A 10/10/2018 2
STEP 1
ASSEMBLY INSTRUCTIONS
STEP 2
STEP 3
Lay the Top (1) upside down on a
at, soft surface. Ensure all holes
are free of debris.
Screw the Rails (5) onto the Top
with Screws (17).
5
1
Prepare the “goalpost” Leg (3,4)
by placing the Expander Plates(9)
into the brackets.
If the desk is to have a Modesty
Panel, screw the Minix bolts (13)
into the holes in the Legs.
Place the Spacers (10) over the
Bolts.
If no Modesty Panel is to be tted,
ll the holes with the 5mm Hole
Plugs (19).
If your desk is to have a Modesty
panel, it needs to be tted at this
step.
Screw the Minix Bolts (12) into
the Top. Place the Spacers (10)
over the Bolts.
Place Cams (14) into the Modesty
Panel (2). Ensure the arrow on the
Cam points towards the edge of
the panel.
Carefully place the Modesty Panel
over the Bolts/Spacers in the Top.
Lock the Cams with just over half
a turn.
17
3
10
13
9
2
12
10
14
Note the position of the
notch in the end of the
Rails – for positioning
Leg at step 4
4
+

No. 113 A/1882 Revision A 10/10/2018 3
ASSEMBLY INSTRUCTIONS
STEP 4
STEP 5
Slide the brackets on the Legs
into the open notched ends of the
Rails screwed to the Top.
If a Modesty Panel is attached,
ensure that the Bolts in the Leg
are aligned with the appropriate
holes in the Modesty Panel.
Lock the Cams with just over half
a turn.
Screw the Grub Screws (18) into
the Expander Plate through the
hole in the Rail. Do Not tighten the
Grub Screws yet.
Place the Spacer (11) between
the Top and the longest Leg and
align it with the hole near the front
upright.
Screw Socket Head Bolt (16)
through the Leg and Spacer into
the Top.
Tighten the Grub Screws until the
Expander Plate is pushed tight to
the inside of the Rail. Tighten the
Socket Head Bolt.
Fit the Cam Cover Caps (15).
3
4
16
18
11
15
18

No. 113 A/1882 Revision A 10/10/2018 4
ASSEMBLY INSTRUCTIONS
CARE AND MAINTENANCE
STEP 6
Clean using a damp cloth and mild detergent – do not use abrasive cleaners or bleach.
Carefully turn the Desk upright.
Fit the Cable Ports (6) and Covers
(7).
Adjust the Feet to level the Desk.