Evolution Aqua evoUV evo30 User manual

INSTALLATION AND OPERATING MANUAL
Complete instructions for all models of evoUV
WARNING:
Evolution Aqua Ltd. - Evolution House - Kellet Close - Wigan - Lancashire - United Kingdom - WN5 0LP
t [phone] - f+44 (0) 1942 216562 - e[email protected] - wwww.evolutionaqua.com
30
UK
English
• Ensure that the unit is switched off at the mains before you attempt to
conduct any type of maintenance on the evoUV.
• Ensure that the gland nut / end cap is tight before running the unit.
• After replacing bulbs or before tightening the end cap, make sure that the
seals are in the correct position, and the bulb socket is dry.
• Should the electrical connections get wet, please dry thoroughly before
switching power on.
• Tampering with the cover plate or serial number plate will invalidate the
warranty. There are NO user serviceable parts behind these panels.
EVO1230920141MAN

WARNING: PLEASE READ THE FOLLOWING
SAFETY INFORMATION FIRST.
IMPORTANT SAFETY INFORMATION
- Please Read Carefully
- Never look directly at an illuminated UV bulb.
- Do not run this unit dry. Do not cover this unit.
- Please ensure that the unit is full of water before switching it on.
- Always isolate the unit from mains electricity and turn off any water supply before
carrying out any maintenance.
- Always disconnect all pond appliances from the mains supply before putting your
hands into the water.
- Use in the area of the garden pond only if the installation complies with the
relevant wiring regulations.
- Power must be supplied through a Residual Current Device (RCD) with a residual
operating current not exceeding 30mA.
- This unit must be earthed. Never use a fuse larger than 3 amps on the power lead.
- The unit must not be submerged in water.
- If the quartz sleeve is cracked, replace it immediately.
- The unit must be either fully frost protected or taken inside during Winter months.
- Young children should always be supervised near water.
PRODUCT INFORMATION
- Rating:
220-240V, 50Hz.
evo30 is 33-36 watt. evo55 is 40-50 watt. evo110 is 67-81 watt.
- Rating in USA only:
100-277V, 50/60Hz.
evo55 is 44-52 watt. evo110 is 67-87 watt.
- All units are Class 1, IP64. All units are CE approved.
Disposal Of Your Old Product
Your product is designed and manufactured with high quality material and components,
which can be recycled and reused. When this crossed-out wheeled bin symbol is
attached to a product, it means the product is covered by the European Directive
2002/96/EC. Please contact your local authority about correct disposal for electrical
and electronic equipment. Our WEE Registration Number is WEE/FE1471RR.
Please act according to your local rules and do not dispose of your old products with
your normal household waste. The correct disposal of your old product will help prevent
potential negative consequences for the environment and human health.

INTRODUCING EVOLUTION AQUA’S evoUV
Congratulations on purchasing an Evolution Aqua evoUV. Our range of evoUV
pond clarifiers have been manufactured using the latest technology and design
techniques. evoUVs have been designed to clear green water which is caused by
single celled green algae and prevent it from returning. evoUVs will work alongside
many different filtration systems but when used alongside Evolution Aqua’s pond
filtration systems, the evoUV will deliver crystal clear and healthy pond water.
Please read this instruction manual carefully from start to finish before attempting
to install your evoUV.
3
CONTENTS
evoUV Diagrams PAGE 4
evoUV Components List PAGE 5
Flow Rates PAGE 6
Installing the evoUV for the first time PAGE 7
Positioning and Mounting the evoUV PAGE 8
Connection to Your Pipework PAGE 11
Connection to the Electricity Supply PAGE 13
UV Bulb Replacement PAGE 14
Replacing / Cleaning the Quartz Sleeve PAGE 15
In Built Protection PAGE 16
Guarantee PAGE 16
Trouble Shooting PAGE 17
Frequently Asked Questions PAGE 18

evoUV DIAGRAMS
INLET / OUTLET
MAINS POWER CABLE
(A)
INLET / OUTLET
INLET / OUTLET
(A)
INLET / OUTLET
FACTORY SEALED BALLAST COVER
(DO NOT REMOVE)
(B)
(C)
(C)
(D)(L)
(D)
(L)
(H)
(H)
(I) (M)
(I)
(F)
(F) (B)
(G)
(G)
30
(E)
(J)
(K)
(J)
(K)
DIMENSIONS:
evo30 and evo55 including factory fitted attachments:
1000 x 185 x 115mm
DIMENSIONS:
evo110 including factory fitted attachments:
1000 x 260 x 115mm
SERIAL NUMBER PLATE
on the back of the unit
(DO NOT REMOVE)
SERIAL NUMBER PLATE
on the back of the unit
(DO NOT REMOVE)
FACTORY SEALED BALLAST COVER
(DO NOT REMOVE)
MAINS POWER CABLE
(M)
4

5
Description evo30 evo55 evo110
1½” Hosetail A A -----------------------------
End Cap B B B
UV Bulb C C C
Quartz Sleeve D D D
Hosetail O-ring E E -----------------------------
Gland Nut F F F
Bulb Socket G G G
O-ring (Quartz Sleeve) H H H
Gland Nut Sleeve I I I
Drain Plug J J J
EPDM Washer K K K
Locking Nut L L L
End Cap Sealing Ring M M M
evoUV COMPONENTS LIST
Cross reference the components listed below, with the diagrams on the previous page.
Gland Nut End Cap UV Bulb
Bulb Socket Locking
Nut
Gland Nut Sleeve
Gland Nut Assembly Drain Plug
(HAND TIGHTEN ONLY)
EPDM Washer
End Cap Sealing Ring

6
It is important to note that there are factors that affect how you select the right size
of evoUV for your pond.
Your evoUV will keep your pond clear of green water up to its maximum capacity as
stated on the box for the evo30 and evo55. The evo110 is an effective unit and has
multiple uses. It can be used on large ponds, retail installations, aquaculture and
other commercial aquaria installations. Please see your local Evolution Aqua dealer
for details.
evo30 evo55 evo110
PONDS UP TO 30,000 litres 55,000 litres 75,000 litres
You will need to take into consideration such things as stocking levels, sunlight /
shade, daily sunshine amounts etc. This is not always possible to calculate, and if
this is the case, apply the rules of thumb below as a guide.
USA - Southern States / Mediterranean 3 Watts UV per 1,000 litres
Northern Europe including UK 2 Watts UV per 1,000 litres
USA - Northern States / Canada 1 Watts UV per 1,000 litres
It must be stressed however, that these are only guidelines, and you should take
advice from your local Evolution Aqua dealer.
Description evo30 evo55 evo110
Maximum Flow Rate 15,000 litres/hour 27,500 litres/hour 36,500 litres/hour
Bulb life 9000 hours 9000 hours 9000 hours
Bulb – with EA code 1 x 30 Watt EVOBT30 1 x 55 Watt EVOBT55 2 x 55 Watt EVOBT55
Inlet / Outlet 1½” BSP male thread 1½” BSP male thread 2” BSP male thread
Inlet / Outlet USA Models N/A 2” NPT male thread 2” NPT male thread
Evolution Aqua order
codes for UK hardpipe
fittings only
Adaptor– K82-23-55 Adaptor– K82-23-55 Adaptor– K82-23-66
Union – K82-78-55 Union – K82-78-55 Union – K82-78-66
or or or
FLOW RATES
Please note: For optimum performance we recommend that you pass the entire
volume of your pond through the evoUV unit once every 2 to 3 hours.
We do not recommend the use of pumps with operating pressures in excess of
2 bar.

7
INSTALLING THE evoUV FOR THE FIRST TIME
1. Unscrew the black end cap, taking care to keep the end cap sealing ring safe.
2. Carefully remove the UV bulb and put to one side for later installation.
3. Ensure the locking nut is tight, compressing the O-ring against the quartz sleeve.
It is not necessary to use tools for this.
4. Position the evoUV and connect your pipework as shown on pages 8 to 12.
5. Before you install the bulb and end caps you should run water through the system
until you are satisfied that there are no leaks.
6. Once you are satisfied with your installation you can now fit the bulb (see below)
and connect the unit to the power supply (see page 13).
To fit the UV Bulb:
• Slide the bulb carefully into the quartz sleeve.
• Starting with either end, you will notice that the gland nut assembly is loose to enable
the cable to move freely.
• Push enough wire through the end cap to give access to the bulb socket. Slip the end
cap sealing ring into position, push the bulb socket onto the UV bulb.
• Tighten the end cap up to the thread on the locking nut, while ensuring that the end
cap sealing ring is positioned correctly inside the end cap.
• With the gland nut sleeve positioned correctly, tighten up the gland nut assembly.
• Repeat this procedure at the other end.
Bulb
Socket
UV
Bulb
Locking
Nut
(O-ring is inside
compressing the
quartz sleeve)
End Cap
Sealing
Ring
End Cap Gland
Nut
Gland
Nut
Sleeve
Gland
Nut
Thread
Mains
Cable
evoUV
Body
Gland Nut
Assembly

8
evoUV units are splashproof but not waterproof. The unit can be positioned either
on a horizontal or vertical surface.
When installing vertically, position the unit with the drain plug at the bottom.
Your evoUV must not be submerged in water or placed in a position where water
may collect around the unit.
Fix your evoUV into position using the stainless steel brackets attached to the
evoUV. Screws and washers are not provided. On the evo30 and evo55 models
a third bracket is attached to the rear serial number plate. This bracket is angled
down during transit. Turn the bracket upright to install.
When fixing to the wall please leave a 1 metre gap at one end of the evoUV to
enable bulb / quartz sleeve removal and maintenance.
If installing the unit prior to or without a pond filter, we would recommend that the
use of a pre-filter is used on the water pump to prevent excess solids from being
pumped into the unit. The evoUV may be connected to the water flow on any
pumped line, this could be, for instance, a skimmer line or any other additional
pumped line. The two most common forms of set up are pump fed and gravity fed.
These are illustrated on the following pages.
It is possible that because of the positioning of your pipework, you may want to
install the evoUV upside down. Your evoUV can be positioned in this way, but it is
likely to cause an air lock. If this occurs the drain plug can then be used to release
the trapped air.
Positioning the evoUV this way will mean that the drain plug can not be used to
drain the unit, therefore extra care must be taken during maintenance and when
the bulb and quartz sleeve are being replaced to ensure the end caps and electrical
connections are kept dry.
The table below shows the inlet and outlet sizes of the evoUV:
MODEL UK AND EUROPE USA AND CANADA
evo30 1½” BSP N/A
evo55 1½” BSP 2” NPT
evo110 2” BSP 2” NPT
POSITIONING AND MOUNTING THE evoUV

9
POSITIONING AND MOUNTING THE evoUV
PLEASE NOTE:
Always leave approximately 1 metre of free space at one end of the
evoUV for UV bulb and Quartz Sleeve maintenance.
MOUNTED ON ITS BACK
Drain plug should be used as an
air release valve in this installation.
MOUNTED HORIZONTALLY
MOUNTED HORIZONTALLY
BUT UPSIDE DOWN
MOUNTED HORIZONTALLY
MOUNTED
VERTICALLY

10
POND
FILTER
EVOUV
MAINS
POWER
LEAD
POND
WATER
PUMP
PUMP
SYMBOL KEY:
DIRECTION OF
WATER FLOW
POSITIONING AND MOUNTING THE evoUV
Gravity Fed Installation
Pump Fed Installation
PLEASE NOTE:
On Gravity Fed systems it is recommended to install a ball valve either side of the
evoUV for maintenance.
POND
WATER LEVEL
PUMP
SYMBOL KEY:
DIRECTION OF
WATER FLOW
BALL VALVE /
SERVICE VALVE
EVOUV
POND
FILTER
WATER
PUMP
MAINS
POWER
LEAD

CUT AND REMOVE
UNWANTED HOSETAILS
CONNECTION TO YOUR PIPEWORK
Connection with flexible hose (evo30 and evo55 only)
The evo30 and evo55 is supplied with two universal hosetails to take 1”, 1¼”,
and 1½” diameter flexible hose. If you are using one of the two larger sizes, the
smaller sections of the hosetails must be cut off to ensure sufficient water flow and
to prevent possible damage to the pump. We recommend that you use the largest
diameter hose available. The hosetails should be trimmed away from the unit as
shown in the diagram below. Once the hosetails have been trimmed, attach them to
the unit as shown below. Secure the flexi-hose to the hosetail with a stainless steel
hose clip (not provided).
The two universal hosetails supplied with the evo30 and evo55, should be screwed
into the inlet / outlet at either end of the unit. Hosetails should be tightened using
hand pressure only. Ensure that the O-rings are in position before assembling.
Please note that there is no correct direction of flow through the unit, either end of
the unit may be used as the inlet or outlet.
* Pipework fittings are not provided with the evo110.
11
CUT
1½” 1¼” 1”
CUT
Screw into
evo30
or evo55
(Hand tight
only)
Use these fittings to connect 1½" Flexible Hose to an evo30 and evo55.
Use a stainless steel hose clip (not supplied) to secure the hose to the fitting.
CONNECTION TO FLEXIBLE HOSE
EA FITTING CODE:
HOSETAIL15TH
Threaded Hosetail Fitting
O-ring
This fitting is provided with the
evo30 and evo55 only.

CONNECTION TO YOUR PIPEWORK
12
Connection using rigid pipe (evo30, evo55 and evo110)
The unit may also be rigid plumbed by the use of an adaptor (not supplied).
See table on page 6 for relevant fittings. These fittings will screw directly into the
evoUV and will enable you to connect to the relevant size pipework.
For other installation options please refer to the Evolution Aqua website
http://evolutionaqua.com/acatalog/evoUV.html
The table below shows the inlet and outlet sizes of the evoUV:
MODEL UK AND EUROPE USA AND CANADA
evo30 1½” BSP N/A
evo55 1½” BSP 2” NPT
evo110 2” BSP 2” NPT
evo110 Installation
We recommend that 2" pipework is used into and out of the evo110 for as long a
run as possible. This ensures the most efficient flow through the evoUV.

CONNECTION TO THE ELECTRICITY SUPPLY
Electrical installations must be done by a qualified electrician.
The power supply must meet the specifications on the product.
The cores in the supply cable are coloured in accordance with the
following code:
Brown = Live. Blue = Neutral. Earth = Green/Yellow.
Do not use the supply cable to lift the evoUV as this may cause damage.
WARNING - A Residual Current Device (RCD), also known as the
Residual Current Circuit Breaker (RCCB), with a tripping current not
exceeding 30mA must be installed in the supply circuit. A means
of disconnection from the supply having a contact separation of at
least 3mm in all poles must be incorporated in the wiring.
Caution: Use in the area of the garden pond only if the installation complies with
the relevant wiring regulations. Please consult a qualified electrician.
Caution: Always disconnect all pond appliances from the mains supply before
putting your hands into the water.
All electrical installations and wiring must be adequately protected to prevent
any damage.
Enough electrical cable is supplied with the unit to connect to the mains electric.
This unit must be connected to permanent wiring. A switch with 3mm contact
separation must be provided in the fixed wiring to provide disconnection from the
electricity supply.
13

14
ROUTINE MAINTENANCE
UV Bulb Replacement
ALWAYS ISOLATE THE UNIT FROM ANY ELECTRICITY AND WATER SUPPLIES
BEFORE CARRYING OUT MAINTENANCE ON THE UNIT.
To Change the Bulb:
It is not necessary to stop the water circulating through the evoUV to change the bulb.
1. On the side that you wish to pull the UV bulb out, slacken off the gland nut on the end
cap to release the cable.
2. Unscrew the end cap taking care not to lose the end cap sealing ring.
3. Disconnect the bulb socket.
4. With the end cap out of the way, carefully slide out the UV bulb. (You may need to pull
firmly on the bulb in order to disconnect it from the bulb socket at the other end.)
5. Slide in the new UV bulb gently turning the bulb until the pins locate in the bulb socket
at the closed end of the unit.
If you have difficulty locating the pins, you can remove the end caps at both ends to
make replacing the bulb easier.
6. Once you have attached the bulb socket, replace the end cap ensuring the end cap
sealing ring is located correctly.
7. Replace the gland nut sleeve and tighten up the gland nut.
WARNING: If the end caps / electrical connections get wet during this procedure,
please ensure that they are thoroughly dried before re-connecting.
After checking all the fittings are correctly tightened, you can switch your unit back on.
As already mentioned, it is essential that the unit is protected from frost during the winter
months, or disconnected from water and electricity supplies and stored indoors. During the
spring and summer season, the quartz sleeve, which separates the UV bulb from the water
passing through the unit, will need to be cleaned two or three times. This is essential,
as dirt or limescale building up on the quartz sleeve will inhibit the penetration of the
ultraviolet light into the water and affect the efficient working of the unit.
evo110 Bulbs Only:
If only one bulb lights up on the evo110 you should
carry out some initial checks to ascertain if the UV
bulb has failed.
• Swap over the end connectors on each bulb at one
end of the evoUV.
• Check that the end connectors are completely dry
and are connected properly.
• Replace the UV bulb.
At one end
of the
evo110 only.
Swap over
end cap and
connectors.

15
Replacing / Cleaning Quartz sleeve
ALWAYS ISOLATE THE UNIT FROM ANY ELECTRICITY AND WATER SUPPLIES
BEFORE CARRYING OUT MAINTENANCE ON THE UNIT.
To Replace / Clean the Quartz Sleeve:
Switch off pumps and if possible isolate the evoUV by closing any valves.
1. Drain the water from the evoUV by unscrewing the drain plug.
(You may need to bleed some air, do this by partially unscrewing the connection
on the inlet or outlet.)
2. Once completely drained, remove the UV bulb as described on page 14. You will
need to undo both end caps.
3. Unscrew the locking nuts which hold the quartz sleeve in place. Taking care not
to lose the O-rings.
4. Gently slide out the sleeve, taking care not to allow it to drop inside the UV body.
5. Clean the sleeve and polish with a soft cloth or paper towel. If you live in a
hard water area, you may get limescale on the quartz sleeve; this can be easily
removed by using vinegar or a cold water descaler.
6. Replace the quartz sleeve by sliding it back into the evoUV, ensuring that an
equal amount of the sleeve is showing at each end.
7. Slide the two O-rings back into position on each end of the quartz sleeve,
and screw on the locking nuts tightly until the seals are compressed.
8. Now replace the bulb as described on page 14.
WARNING: If the end caps / electrical connections get wet during this procedure,
please ensure that they are thoroughly dried before re-connecting.
During this procedure or if you notice water leaking from around the end caps you
should check the following:
1) Check the O-ring is undamaged.
2) Check there are no cracks and breaks in the quartz sleeve.
3) Check that the locking nut is compressing the O-ring to form a water tight seal.
4) Check that the gland nut and gland nut sleeve are installed correctly
and are tight.
5) Check that the end caps are sufficiently tight.
6) All components are clean and free from dirt and debris.
*Please note that the items mentioned under the list 1-6 are service items and
therefore not subject to a claim under warranty. The service items listed are
available from your EA stockist.

16
In Built Protection
The evoUV range of pond clarifiers have thermal overload protection which
automatically shuts down and then enables a fast re-start when the problem
has been cleared. This may be as a result of water in the end caps. Please see
the troubleshooting section on page 17.
Thermal Overload Protection (Only on evo55 and evo110 models) -
This will automatically switch off the unit should the temperature exceed the
maximum operating temperature limits.
Automatic start up and shut down protection - This protects the electrical
components in the event of a power surge.
OUR GUARANTEE
This product is guaranteed against defects in material and workmanship for 2 years
from the date of purchase, under normal usage. The guarantee DOES NOT APPLY
in case of improper use, negligence, lack of maintenance or accidental damage to
the evoUV. If the evoUV fails due to a manufacturing fault within this period it will
be either repaired or replaced free of charge. Liability is limited to replacement of
the faulty product only; no other costs will be reimbursed. This guarantee is not
transferable and does not affect your statutory rights. This guarantee does not confer
any rights other than those expressly set out above. This guarantee does not cover the
evoUV bulb or quartz sleeve.
Tampering with the cover plate or serial number plate will invalidate the warranty.
There are NO user serviceable parts behind these panels.
The manufacturer or supplier shall not be responsible, or held liable for any damages
caused by defective components or materials of this product; or for loss incurred by
interruption of service; or any consequential/incidental damages and expenses arising
from the production, sale use or misuse of this product.
Any warranty claim must be accompanied by a valid, dated proof of purchase.
Evolution Aqua and its dealers shall not be held liable for any loss of fish, plants or
any other livestock as a result of any failure or defect of this product.
The evoUV has a serial number plate attached to the back of the unit. If this serial
number plate has been removed or tampered with, this will void the warranty.
The installation and use of your product outside of our recommendations as printed in
this manual may also void the warranty.

17
TROUBLE SHOOTING
My pond water is not clear, is this due to the evoUV not working correctly?
Koi, goldfish and other pond inhabitants can cause murky water by stirring up the
bottom of the pond. This murky water should not be confused with suspended algae.
Always check all your pond filtration is working and is being maintained correctly
prior to checking the evoUV.
If the UV bulb is not lit, then you need to investigate the power to your unit.
• Has your RCD tripped? If yes, check your wiring and reset.
• Examine the UV bulb for signs of failure, and replace if necessary.
• Is the UV bulb fitted correctly? Unscrew the end caps and ensure correct fitting as
per the instructions on page 14.
• Are the end caps dry? If not, allow to dry thoroughly. We recommend the use of a
hair-dryer for this.
If only one bulb is lit up on the evo110 only.
• Please check the UV bulb as per UV bulb maintenance on page 14.
• If one bulb is still not lit, swap the bulb end connectors at one end of the evo110.
The unit worked well when I first installed it but recently my pond has gradually
gone green again – what is wrong?
Quartz sleeve may have become dirty and requires cleaning (see page 15). Also
make sure you have the right model for your pond size. Ensure your pond filtration is
removing fish waste and debris efficiently. Dirt in ponds will affect the efficiency of
the evoUV. Check that your pond water volume is pumping through the evoUV every
2 to 3 hours.
Only after you have carried out these checks should you contact your Evolution Aqua
dealer, who will then be able to advise you further.
At one end
of the
evo110 only.
Swap over
end cap and
connectors.

18
FREQUENTLY ASKED QUESTIONS
How often should I change the UV bulb?
The evoUV bulb has an effective lifespan of 9000 hours, but it is an accepted
practice to replace a UV bulb once a year, at the start of every pond season.
How long after I install the unit will my pond become clear?
There are many factors which affect how long your evoUV will take to clear your
pond, such as the levels of nutrients available to the algae, the water temperature
and the level of sunlight. Assuming that you have installed the correct size unit,
most ponds should clear within 3-14 days. However, this may take up to six weeks
in some instances.
Does the evoUV harm fish, plants or wildlife?
Ultraviolet bulbs leave no residues, and only affect the water pumped through the
unit. Unlike many chemical treatments, your evoUV will not harm the plants and
animals living in the water.
Is the evoUV suitable for salt water use?
The evoUV is manufactured from materials that will not corrode in salt water and it
is safe to use your evoUV in marine systems.
Can I use my evoUV if I am using any treatments for my fish?
Always check the manufacturer’s instructions before using any water treatment as
they will tell you whether it’s recommended that the evoUV can be switched off or
on.
How long can I leave the unit running?
evoUVs have been designed and manufactured to the highest standards, and should
be run 24 hours a day, every day, from mid March to early October, depending on
the weather conditions. If the unit is frost protected it may be left running throughout
the winter. Otherwise, the unit should be removed, drained and stored safely for
the winter.
Can I bury the unit underground?
No. The evoUV, although weatherproof, is not suitable for installing in any situation
that may be subject to immersion in water.
Can it be used with ozone?
Yes. The evoUV is safe to use with ozone units, however, the O-rings on the
hosetails are not. When using ozone units please use rigid pipe.
When replacing the bulb I cannot locate it into the bulb socket at the opposite end
of the evoUV?
Please follow the procedure for cleaning / replacing the quartz sleeve on page 15.
This will explain the correct procedure for removing both end caps and sockets and
explain the method for easy installation.

TO ACTIVATE YOUR FREE 1 YEAR EXTRA WARRANTY COVER,
COMPLETE THIS FORM & SEND IT TO US TODAY.
Your Name:
Your Address:
Postcode:
Country:
Tel No:
Mobile No:
Email:
Purchased From:
Date of Purchase: / /
Model of evoUV:
Serial Number:
Other Evolution Aqua products I use: (please tick)
Nexus 210 Nexus 310 EazyPod EazyPod Complete Cetus Sieve Dechlorinator
AirPumps Perfect Pumps Sequence Pumps Pure Pond Treatments EA Foods
Please send me information about other Evolution Aqua products including: (please tick)
Nexus 210 Nexus 310 EazyPod EazyPod Complete Cetus Sieve Dechlorinator
AirPumps Perfect Pumps Sequence Pumps Pure Pond Treatments EA Foods
Your evoUV comes with a 2 year warranty. To extend this for no additional cost,
simply complete the information below and return this form to us by post, email or
fax, and receive a further 1 year warranty cover from the date of purchase on your
evoUV. This gives you peace of mind for a full 3 years.
Complete this form, cut it out and return it using one of the following methods:
Signature: Date: / /
I have read and accept the terms and conditions listed in the warranty card, and
understand the obligations of the Customer under this warranty.
Evolution Aqua Ltd. may contact you in the future with product updates or offers, which may be of interest to you.
If you do not wish to receive this information please tick this box.




Scan and email this form to:
[email protected]
Post this in an envelope to:
Evolution House,
Kellet Close, Wigan,
Lancashire, United Kingdom,
WN5 0LP
Fax a copy of this form to:
[phone]

Evolution Aqua Ltd
Evolution House
Kellet Close
Wigan
Lancashire
United Kingdom
WN5 0LP
t: [phone]
f: [phone]
e: [email protected]
w: www.evolutionaqua.com
Evolution Aqua are the award winning pond filtration manufacturer who put
innovation, research and development at the top of their agenda. With a proven
track record for delivering the latest technology to the aquatics and fish farming
markets - we are the first choice for everyone from the general hobbyist to the
serious fishkeeper. Find out more about the evoUV and all of our other innovative
products at www.evolutionaqua.com. The difference is clear.