EWM Tetrix 230 Comfort 2-0 puls User manual

Operating instructions
EN
Control
T 4.03 - DC Comfort 2.0 (Tetrix 230)
099-00T403-EW501 Observe additional system documents! 04.09.2017
Register now
and benefit!
Jetzt Registrieren
und Profitieren!
www.ewm-group.com
*For details visit
www.ewm-group.com
*

General instructions
WARNING
Read the operating instructions!
The operating instructions provide an introduction to the safe use of the products.
•Read and observe the operating instructions for all system components, especially the
safety instructions and warning notices!
•Observe the accident prevention regulations and any regional regulations!
•The operating instructions must be kept at the location where the machine is operated.
•Safety and warning labels on the machine indicate any possible risks.
Keep these labels clean and legible at all times.
•The machine has been constructed to state-of-the-art standards in line with any applicable
regulations and industrial standards. Only trained personnel may operate, service and
repair the machine.
•Technical changes due to further development in machine technology may lead to a
differing welding behaviour.
In the event of queries on installation, commissioning, operation or special conditions at the
installation site, or on usage, please contact your sales partner or our customer service
department on [phone].
A list of authorised sales partners can be found at www.ewm-group.com.
Liability relating to the operation of this equipment is restricted solely to the function of the
equipment. No other form of liability, regardless of type, shall be accepted. This exclusion of
liability shall be deemed accepted by the user on commissioning the equipment.
The manufacturer is unable to monitor whether or not these instructions or the conditions and
methods are observed during installation, operation, usage and maintenance of the equipment.
An incorrectly performed installation can result in material damage and injure persons as a
result. For this reason, we do not accept any responsibility or liability for losses, damages or
costs arising from incorrect installation, improper operation or incorrect usage and maintenance
or any actions connected to this in any way.
© EWM AG
Dr. Günter-Henle-Straße 8
56271 Mündersbach
Germany
The copyright to this document remains the property of the manufacturer.
Copying, including extracts, only permitted with written approval.
The content of this document has been prepared and reviewed with all reasonable care. The information
provided is subject to change; errors excepted.

Contents
Notes on t
he use of these operating instructions
099-00T403-EW501
04.09.2017
3
1 Contents
1Contents.................................................................................................................................................. 3
2For your safety ....................................................................................................................................... 5
2.1 Notes on the use of these operating instructions ..........................................................................5
2.2 Explanation of icons....................................................................................................................... 6
2.3 Part of the complete documentation.............................................................................................. 7
3Machine control – Operating elements................................................................................................ 8
3.1 Overview of control sections..........................................................................................................8
3.1.1 Control section A ............................................................................................................ 9
3.1.2 Control section B ..........................................................................................................10
3.2 Machine display ........................................................................................................................... 12
3.2.1 Setting the welding current (absolute/percentage)....................................................... 12
3.3 Operating the machine control.....................................................................................................12
3.3.1 Main screen .................................................................................................................. 12
3.3.2 Welding power setting .................................................................................................. 12
3.3.3 Welding parameter setting in the operation sequence................................................. 13
3.3.4 Setting advanced welding parameters (Expert menu) ................................................. 13
3.3.5 Changing basic settings (machine configuration menu) .............................................. 13
4Functional characteristics................................................................................................................... 14
4.1 TIG welding..................................................................................................................................14
4.1.1 Gas test – setting the shielding gas volume.................................................................14
4.1.2 Welding task selection..................................................................................................15
4.1.2.1 Recurring welding tasks (JOB 1–7) .............................................................. 15
4.1.3 Arc ignition.................................................................................................................... 16
4.1.3.1 HF ignition .....................................................................................................16
4.1.3.2 Liftarc ............................................................................................................ 16
4.1.3.3 Automatic cut-out .......................................................................................... 16
4.1.4 Operating modes (functional sequences) ....................................................................17
4.1.4.1 Explanation of symbols ................................................................................. 17
4.1.4.2 Non-latched mode......................................................................................... 18
4.1.4.3 Latched mode ............................................................................................... 19
4.1.4.4 spotArc ..........................................................................................................20
4.1.4.5 spotmatic.......................................................................................................22
4.1.5 TIG activArc welding..................................................................................................... 23
4.1.6 TIG antistick.................................................................................................................. 23
4.1.7 Pulse welding ............................................................................................................... 24
4.1.7.1 Automated pulses ......................................................................................... 24
4.1.7.2 Thermal pulsing............................................................................................. 24
4.1.7.3 Pulsed welding in the upslope and downslope phases ................................ 25
4.1.7.4 Average value pulse welding ........................................................................26
4.1.7.5 Metallurgical pulsing (kHz pulsing) ............................................................... 26
4.1.8 Welding torch (operating variants) ............................................................................... 27
4.1.8.1 Tapping function (tap torch trigger)............................................................... 27
4.1.8.2 Torch mode setting ....................................................................................... 27
4.1.8.3 Up/down speed ............................................................................................. 28
4.1.8.4 Current jump .................................................................................................28
4.1.8.5 Standard TIG torch (5-pole) ..........................................................................28
4.1.8.6 TIG up/down torch (8-pole) ........................................................................... 30
4.1.8.7 Potentiometer torch (8-pole) ......................................................................... 31
4.1.8.8 Configuring the TIG potentiometer torch connection....................................33
4.1.8.9 RETOX TIG torch (12-pole) ..........................................................................33
4.1.9 Expert menu (TIG)........................................................................................................34
4.2 MMA welding ............................................................................................................................... 35
4.2.1 Welding task selection..................................................................................................35
4.2.2 Hotstart ......................................................................................................................... 35
4.2.2.1 Hotstart current ............................................................................................. 35
4.2.2.2 Hotstart time..................................................................................................36
4.2.3 Antistick ........................................................................................................................ 36
4.2.4 Average value pulse welding........................................................................................ 37

Contents
Notes on the use of these operating instructions
4 099-00T403-EW501
04.09.2017
4.3 Power-saving mode (Standby).....................................................................................................37
4.4 Access control..............................................................................................................................38
4.5 Voltage reducing device...............................................................................................................38
4.6 Machine configuration menu........................................................................................................39
4.6.1 Selecting, changing and saving parameters.................................................................39
5Rectifying faults....................................................................................................................................40
5.1 Error messages (power source)...................................................................................................42
5.2 Dynamic power adjustment..........................................................................................................42
5.3 Resetting welding parameters to the factory settings ..................................................................43
5.4 Display machine control software version....................................................................................43
6Appendix A............................................................................................................................................44
6.1 Parameter overview – setting ranges ..........................................................................................44
6.1.1 TIG welding...................................................................................................................44
6.1.2 MMA welding ................................................................................................................45
7Appendix B............................................................................................................................................46
7.1 Overview of EWM branches.........................................................................................................46

For your safety
Notes on the use of these operating instructions
099-00T403-EW501
04.09.2017
5
2 For your safety
2.1 Notes on the use of these operating instructions
DANGER
Working or operating procedures which must be closely observed to prevent imminent
serious and even fatal injuries.
•
Safety notes include the "DANGER" keyword in the heading with a general warning symbol.
•The hazard is also highlighted using a symbol on the edge of the page.
WARNING
Working or operating procedures which must be closely observed to prevent serious
and even fatal injuries.
•Safety notes include the "WARNING" keyword in the heading with a general warning
symbol.
•The hazard is also highlighted using a symbol in the page margin.
CAUTION
Working or operating procedures which must be closely observed to prevent possible
minor personal injury.
•The safety information includes the "CAUTION" keyword in its heading with a general
warning symbol.
•The risk is explained using a symbol on the edge of the page.
Special technical points which users must observe.
Instructions and lists detailing step-by-step actions for given situations can be recognised via bullet
points, e.g.:
•Insert the welding current lead socket into the relevant socket and lock.

For your safety
Explanation of ico
ns
6 099-00T403-EW501
04.09.2017
2.2 Explanation of icons
Symbol
Description
Symbol
Description
Indicates technical aspects which the
user must observe.
Activate and release/tap/tip
Switch off machine
Release
Switch on machine
Press and keep pressed
Switch
Wrong
Turn
Correct
Numerical value – adjustable
Menu entry
Signal light lights up in green
Navigating the menu
Signal light flashes green
Exit menu
Signal light lights up in red
Time representation (e.g.: wait
4 s/activate)
Signal light flashes red
Interruption in the menu display (other
setting options possible)
Tool not required/do not use
Tool required/use

For your safety
Part of the complete documentation
099-00T403-EW501
04.09.2017
7
2.3 Part of the complete documentation
These operating instructions are part of the complete documentation and valid only in
combination with all other parts of these instructions! Read and observe the operating
instructions for all system components, especially the safety instructions!
The illustration shows a general example of a welding system.
Figure 2-1
Item
Documentation
A.1
Options conversion instructions
A.2
Power source
A.3
Cooling unit, voltage converter, tool box etc.
A.4
Transport cart
A.5
Welding torch
A.6
Remote control
A.7
Control
A
Complete documentation

Machine control
– Operating elements
Overview of control sections
8 099-00T403-EW501
04.09.2017
3 Machine control – Operating elements
3.1 Overview of control sections
For description purposes, the machine control has been divided into two sections (A, B) to
ensure maximum clarity. The setting ranges for the parameter values are summarised in the
parameter overview section > see 6.1 chapter.
Figure 3-1
Item
Symbol
Description 0
1
Control section A
> see 3.1.1 chapter
2
Control section B
> see 3.1.2 chapter

Machine control –
Operating elements
Overview of control sections
099-00T403-EW501
04.09.2017
9
3.1.1 Control section A
Figure 3-2
Item
Symbol
Description 0
1
Welding data display (3-digit)
Displays the welding parameters and the corresponding values > see 3.2 chapter
2
Gas test push-button > see 4.1.1 chapter
3
Operating mode > see 4.1.4 chapter / power-saving mode push-
button > see 4.3 chapter
--------- Latched
------- Non-latched
------ spotArc spot welding procedure – signal light turns green
------ spotmatic spot welding procedure –signal light turns red
-------- Press button for long interval to put machine into power-saving mode.
Activate one of the operating elements to reactivate.
4 Pulsing push-button > see 4.1.7 chapter
------ Automated pulsing (frequency and balance)
-------- Signal light turns green: Thermal pulsed TIG welding/MMA pulse
welding/average value pulsing
-------- Signal light turns red: Metallurgical pulsed TIG welding (kHz pulsing)
5
Welding procedure push-button
--------- TIG welding
--------- MMA welding
6
Display switching push-button
kW ------- Welding power display
V---------- Welding voltage display
JOB ------ Display and setting of the JOB number with the control button
7
Welding data display (3-digit)
Displays the welding parameters and the corresponding values > see 3.2 chapter
8 TIG ignition type signal light
Signal light on: Lift arc ignition active/HF start off. You can switch the ignition type in the
Expert menu (TIG) > see 4.1.9 chapter.
9
Character function signal light
Indicates that it is possible to weld in an environment with major electric hazards, such
as in boilers. Service must be informed if this signal light is not on.

Machine control
– Operating elements
Overview of control sections
10 099-00T403-EW501
04.09.2017
Item
Symbol
Description 0
10
Coolant fault signal light
Signals pressure loss or low coolant level in the coolant circuit.
11 VRD Voltage reduction device (VRD) signal light
The VRD signal light is illuminated when the voltage reduction device is operating
without fault and the output voltage is reduced to a value specified in the relevant
standard (see technical data) > see 4.5 chapter. The voltage reduction device is only
active on VRD machine versions.
12 Hold Signal light Status display
After each completed welding task, the last values used in the welding process for the
welding current and welding voltage are shown on the displays, and the signal light will
be on
13
Excess temperature signal light
In case of excess temperature, temperature monitors de-activate the power unit, and
the excess temperature control lamp comes on. Once the machine has cooled down,
welding can continue without any further measures.
14 Access control active signal light
Signal light is on when access control is active on the machine
control > see 4.4 chapter.
15 Without function in this machine version.
3.1.2 Control section B
Figure 3-3
Item
Symbol
Description 0
1
Parameter selection push-button, left
The welding sequence parameters are selected one after another in an anti-clockwise
direction.
2
Control button
Central control button to be pressed or turned > see 3.3 chapter.
3
Parameter selection push-button, right
The welding sequence parameters are selected one after another in a clockwise
direction.
4
Balance signal light
Pulse balance
5
Electrode diameter signal light
Ignition optimisation (TIG)/tungsten balling basic setting

Machine control –
Operating elements
Machine display
099-00T403-EW501
04.09.2017
11
Item
Symbol
Description 0
6
Gas post-flow time
7
AMP%
End current signal light
8 sec Down-slope time signal light
9 AMP%
sec
Signal light, two colour
Red: Secondary or pulse pause current (% of AMP)
Green: Pulse pause time
10 AMP
sec
Signal light, two colour
Red: Main current /pulse current
Green: Pulse time
11 sec
Signal light
Up-slope time (TIG)/hot start time
(MMA)
12 AMP% Signal light
Ignition current (TIG)/hot start current (MMA)
13
Gas pre-flow time signal light
14
Signal light activArc > see 4.1.5 chapter
15 signal light
AC frequency (TIG, JOBs 1–7)/pulse frequency (TIG, average value pulsing)/pulse
frequency (MMA)

Machine contr
ol – Operating elements
Machine display
12 099-00T403-EW501
04.09.2017
3.2 Machine display
The following welding parameters can be displayed before (nominal values), during (actual values) or
after welding (hold values):
"left display"
Parameter
Before welding
(nominal values)
During welding
(actual values)
After welding
(hold values)
Welding current



Parameter times



Parameter currents



Frequency, balance



JOB number



"right display"
Welding power



Welding voltage



When the hold values are displayed after welding and the settings are then changed (e.g. welding
current), the display will switch to the relevant nominal values.
possible
not possible
The parameters that can be set in the function sequence of the machine control depend on the selected
welding task. This means that if for example you have not selected a pulse variant, then you cannot set
any pulse times in the function sequence.
3.2.1 Setting the welding current (absolute/percentage)
The welding current for the ignition, secondary, end and hot start current can be set as a percentage of
the main current AMP or as an absolute value. To select, use the parameter <dg in the configuration
menu_ref_source_inline>Gerätekonfigurationsmenü</dg_ref_source_inline>.
> see 4.6 chapter
3.3 Operating the machine control
3.3.1 Main screen
The machine control switches to the main screen after it has been turned on or a setting has been
completed. This means that the previously selected settings (indicated by signal lights where applicable)
and the nominal value for the current (A) are displayed in the left-hand welding data display. Depending
on the selection, the right-hand display shows the welding voltage (V) nominal value or the welding power
(kW) actual value. The control always switches back to the main screen after 4 sec. of inactivity.
3.3.2 Welding power setting
The welding power is set using the control button. You can also adjust the parameters in the operation
sequence or settings in the different machine menus.

Machine control –
Operating elements
Operating the machine control
099-00T403-EW501
04.09.2017
13
3.3.3 Welding parameter setting in the operation sequence
A welding parameter can be set in two ways in the operation sequence.
1. Push the "left" or "right" arrow keys (flashing signal light will indicate your selection). Turn the control
button to set the parameter value.
2. Press briefly on the control button (operation sequence selection) and then turn the button (navigate to
the required parameter). Press again to apply the selected parameter as the setting (corresponding
parameter value and signal light flash). Turn the button to set the parameter value.
During welding parameter setting, the parameter value to be set flashes in the left hand display. A
parameter abbreviation or a deviation in the specified parameter value upwards or downwards is shown
on the right-hand display:
Display
Meaning
Increase the parameter value
To return to the factory settings.
Factory setting (example value = 20)
Parameter is set to optimum value
Decrease the parameter value
To return to the factory settings.
3.3.4 Setting advanced welding parameters (Expert menu)
The Expert menu contains functions and parameters which cannot be set directly in the machine control
or which do not need to be et on a regular basis. The number and display of these parameters depends
on the previously selected welding procedure or the functions.
To select them hold the control button for more than 2 sec. Select the required parameter/menu item by
turning (navigate) and pressing (confirm) the control button.
You can also or alternatively use the push-buttons to the left and right of the control button to navigate.
3.3.5 Changing basic settings (machine configuration menu)
The basic welding system functions can be adjusted in the machine configuration menu. Only
experienced users should change the settings > see 4.6 chapter.

Functional characteristics
TIG welding
14 099-00T403-EW501
04.09.2017
4 Functional characteristics
4.1 TIG welding
4.1.1 Gas test – setting the shielding gas volume
•Slowly open the gas cylinder valve.
•Open the pressure regulator.
•Switch on the power source at the main switch.
•Set the relevant gas quantity for the application on the pressure regulator.
•The gas test can be activated at the machine control by pressing the "Gas test" push-
button > see 3.1.1 chapter.
Setting the shielding gas quantity (gas test)
•Shielding gas flows for approx. 20 seconds or until the push-button is pressed again.
If the shielding gas setting is too low or too high, this can introduce air to the weld pool and may cause
pores to form. Adjust the shielding gas quantity to suit the welding task!
Setting instructions
Welding process
Recommended shielding gas quantity
MAG welding
Wire diameter x 11.5 = l/min
MIG brazing
Wire diameter x 11.5 = l/min
MIG welding (aluminium)
Wire diameter x 13.5 = l/min (100 % argon)
TIG
Gas nozzle diameter in mm corresponds to l/min gas throughput
Helium-rich gas mixtures require a higher gas volume!
The table below can be used to correct the gas volume calculated where necessary:
Shielding gas
Factor
75% Ar/25% He
1.14
50% Ar/50% He
1.35
25% Ar/75% He
1.75
100% He
3.16
For connecting the shielding gas supply and handling the shielding gas cylinder refer to the
power source operating instructions.

Functional characteristics
TIG welding
099-00T403-EW501
04.09.2017
15
4.1.2 Welding task selection
The setting of the tungsten electrode diameter has a direct influence on the machine functionality, TIG
ignition behaviour and minimum current limits. The ignition energy is controlled by the set electrode
diameter. Smaller electrode diameters requires less ignition current and less ignition current time than
greater electrode diameters. The set value should correspond to the tungsten electrode diameter. The
value can also be set to meet individual requirements, e.g. for thin panels a smaller diameter is
recommended to reduce the ignition energy.
The following welding task is an example of use:
EXIT
4s
mm
inch
Figure 4-1
4.1.2.1 Recurring welding tasks (JOB 1–7)
The user has 7 more memory locations at their disposal to save recurring or different welding tasks on a
permanent basis. To do so, simply select the required memory location (JOB 1–7) and the welding task is
set as described previously.
Switching a JOB is only possible if no welding current flows. Up-slope and down-slope times can be set
individually for latched and non-latched operation.
Selection
Figure 4-2
When one or more of the recurring welding tasks (JOB 1–7) has been selected the JOB signal light
comes on.

Functional characteristics
TIG welding
16 099-00T403-EW501
04.09.2017
4.1.3 Arc ignition
To change the ignition type, use parameter to switch between HF start ( ) and lift arc ( ) in the
Expert menu > see 4.1.9 chapter.
4.1.3.1 HF ignition
Figure 4-3
The arc is started without contact from high-voltage ignition pulses.
a) Position the welding torch in welding position over the workpiece (distance between the electrode tip
and workpiece should be approx. 2-3mm).
b) Press the torch trigger (high voltage ignition pulses ignite the arc).
c) Ignition current flows, and the welding process is continued depending on the operating mode
selected.
End the welding process: Release or press the torch trigger depending on the operating mode
selected.
4.1.3.2 Liftarc
Figure 4-4
The arc is ignited on contact with the workpiece:
a) Carefully place the torch gas nozzle and tungsten electrode tip onto the workpiece and press the torch
trigger (liftarc current flowing, regardless of the main current set).
b) Incline the torch over the torch gas nozzle to produce a gap of approx. 2-3 mm between the electrode
tip and the workpiece. The arc ignites and the welding current is increased, depending on the
operating mode set, to the ignition or main current set.
c) Lift off the torch and swivel to the normal position.
Ending the welding process: Release or press the torch trigger depending on the operating mode
selected.
4.1.3.3 Automatic cut-out
Once the fault periods have elapsed, the automatic cut-out stops the welding process when it has been
triggered by one of two states:
•During ignition
3 s after the start of the welding process, no welding current flows (ignition error).
•During welding
The arc is interrupted for more than 3 s (arc interruption).

Functional characteristics
TIG welding
099-00T403-EW501
04.09.2017
17
4.1.4 Operating modes (functional sequences)
4.1.4.1 Explanation of symbols
Symbol
Meaning
Press torch trigger 1
Release torch trigger 1
I
Current
t Time
Gas pre-flow
Ignition current
Up-slope time
Spot time
AMP
Main current (minimum to maximum current)
AMP%
Secondary current
Pulse time
Pulse pause time
Down-slope time
End-crater current
Gas post-flow
Balance
Frequency

Functional characteristics
TIG welding
18 099-00T403-EW501
04.09.2017
4.1.4.2 Non-latched mode
Selection
Figure 4-5
Sequence
Figure 4-6
1st cycle:
•Press torch trigger 1 and hold down.
•Gas pre-flow time elapses.
•HF ignition pulses jump from the electrode to the workpiece. The arc ignites.
•The welding current flows and immediately assumes the value of the ignition current .
•HF switches off.
•The welding current ramps up to the main current (AMP) in the selected up-slope time .
If torch trigger 2 is pressed together with torch trigger 1 during the main current phase, the welding
current decreases to the secondary current (AMP%).
If torch trigger 2 is released, the welding current increases again to the main current AMP.
2nd cycle:
•Release torch trigger 1.
•The main current falls to the end-crater current (minimum current) in the set down-slope time .
If the 1st torch trigger is pressed during the down-slope time,
the welding current returns to the set main current AMP.
•Main current reaches the end-crater current ; the arc is extinguished.
•Set gas post-flow time elapses.
When the foot-operated remote control is connected, the machine switches automatically to non-latched
operation. The up- and down-slopes are switched off.

Functional characteristics
TIG
welding
099-00T403-EW501
04.09.2017
19
4.1.4.3 Latched mode
Selection
Figure 4-7
Sequence
Figure 4-8

Functional characteristics
TIG welding
20 099-00T403-EW501
04.09.2017
1st cycle
•Press torch trigger 1; gas pre-flow time elapses.
•HF ignition pulses jump from the electrode to the workpiece. The arc ignites.
•Welding current flows and immediately assumes the set ignition current (search arc at minimum
setting). HF switches off.
2nd cycle
•Release torch trigger 1.
•The welding current ramps up to the main current (AMP) in the selected up-slope time .
Switching from the main current AMP to secondary current (AMP%):
•Press torch trigger 2 or
•Tap torch trigger 1 (torch modes 1–6).
3rd cycle
•Press torch trigger 1.
•The main current decreases to the end-crater current within the set down-slope time .
4th cycle
•Release torch trigger 1; arc is extinguished.
•Set gas post-flow time runs.
Ending the welding process immediately without a down-slope or end-crater current:
•Press the 1st torch trigger briefly > 3rd and 4th cycles (torch modes 11–16).
Current drops to zero and the gas post-flow time begins.
When the foot-operated remote control is connected, the machine switches automatically to non-latched
operation. The up- and down-slopes are switched off.
A double-digit torch mode (11-x) needs to be set at the welding machine control to use the
alternative welding start (tapping start). The number of torch modes available depends on the
machine type.
4.1.4.4 spotArc
This process is suitable for tack welding or joint welding of metal sheets made from steel and CrNi alloys
up to a thickness of approximately 2.5 mm. Metal sheets of different thicknesses can also be welded on
top of one another. As this is a one-sided process, it is also possible to weld metal sheets onto tubular
sections such as round or square pipes. In arc spot welding, the arc melts through the upper metal sheet
and the lower metal sheet is melted onto it. This produces flat, fine-textured welding tacks which require
little or no post weld work, even in visible areas.
EXIT
4s
Figure 4-9
The up-slope and down-slope times should be set to “0” to achieve an effective result.