ExBrite DHJSBM242322LALXXX User manual

See Better with Smart Light
Installation and Operating Manual
DHJSBM242322LALXXX DHJSBM2346FLALXXX
DHJSBM2836FLALXXX
DHJSBM2346BLALXXX
DHJSBM2836BLALXXX
DHJSBM3036BLALXXX
DHJSBM4024BLALXXX DHJSBM4024FLALXXX

See Better with Smart Light
WARNING AND SAFETY INSTRUCTIONS
Before assembling your LED Lighted Mirror fixture, please make sure that you carefully
read through this instruction sheet, refer back to them during installation to ensure
your product is fitted safely and correctly. Keep these instructions for future use.
WARNING Risk of Fire and Electric Shock
All fittings must be installed in accordance with current IEE wiring regulations. If in
doubt, consult a qualified electrician.
Switch off the electrical supply at the main circuit board BEFORE installation
and maintenance.
Suitable for indoor use only. This product should be positioned well away from
curtains and fabrics. Never cover the mirror.
Regularly check the cord, the transformer and all other parts for damage. If any
part is damaged the product should not be used.
INSTALLATION SAFETY
Inspect the product immediately upon receipt for the transit damage or missing
parts. Handle the product with care and protect against knocks to all sides and
edges of the glass.
Ensure there are no hidden pipes or cables in the wall before drilling.
Wear suitable eye protection when drilling. Take care if drilling on tiled surfaces
in case the drill slips.
CAUTION
The light source of this product is non‐changeable light diodes (LED). Do not
disassemble the product, as the light diodes can cause damage to the eyes.
NOTE: The important safeguards and instructions that appear in this manual are not
meant to cover all possible conditions and situations that may occur. It must be
understood that common sense, caution and care, are factors that can’t be built into
any product. These factors must be supplied by the person(s) caring for and operating
the fixture. Do not install this fixture in hazardous locations.

See Better with Smart Light
INSTALLATION MANUAL
Level and mark the location.
1
2
CHECK PRODUCT LIST AFTER
OPENING THE PACKAGE
TOOLS YOU MAY NEED
LED Lighted Mirror
Screws for wall
Type A Plastic Anchor
Mounting bar
Installation Manual
‐‐1 pce
‐‐5 pcs
‐‐5 pcs
‐‐1 pce
‐‐1 pce
Place the mounting bar against the wall
and make some marks on the wall.
3
Drill the holes and place the
suitable plastic anchors.
Type B Plastic Anchor ‐‐5 pcs

See Better with Smart Light
Hang the mirror onto the mounting bar.
4
6
Screw the mounting bar onto the wall
with the screws .
5
Connect the mirror with the
main supply.
We provide plug with mirrors.
Optional to cut the plug directly,then
connect to electrical wiring if using
wall switch.
ATTENTION:
PLEASE CUT OFF THE MAIN POWER
SUPPLY BEFORE WIRING!

See Better with Smart Light
OPERATION INSTRUCTION
ON/OFF and Dimmer
ON/OFF button
Press and hold on
for 3‐5 seconds
Defoggerbutton
Short‐touch the button to turn on/off the mirror.
Adjusting color temperatures (CCT) between
warm white and cool white by long‐touching
the button forseconds.
Finish setting by withdrawing your finger
when the color reaches the one you need.
Optional to be wired to wall switch by ON/OFF
memory function.
Anti-Fog Function
Mirror begins to be warm and defog after pressing the
defogger button. Press again to quit the anti‐fog function.
Note: The defogger will stop automatically after60
minutes of continuous operation to prevent any
damage caused by prolonged high temperature.

Short‐touch the button to turn on/off the mirror.
Long touching the button to adjust the
brightness (Dimming).
Button turns blue when connected to main
supply.
Button always on as long as connecting to main
supply.
ON/OFF and CCT adjustment

See Better with Smart Light
Night Light
Bright
sensor
3000K Nightlight
AFTERCARE INSTRUCTIONS
Clean using a soft dry cloth only when turned off. Never use cleaning agents or
abrasive materials. Do not allow moisture to come into contact with lamp.
Night light will be auto‐on/off according
to the brightness surrounding when the
rocker switch is keeping turned on.
If need turn off the nightlight at night,
please turn off the rocker switch manually.
Clock/Temperature


Turn off the light to set the clock.
Long touch button 1or 2 for seconds,the
Hour will flash, then short‐touch button1
and 2 to set Hour.
Wait for seconds after setting up the Hour,
then it will automatically switch to the
Minute flash.
Short‐touch button 1and 2 to set up the
Minute.
Wait seconds after you finish the time
setting,the time will be saved automatically.
The clock shows for 5s, and shift to
the temperature showing for 2s,
then go back to show the clock.
It automatically displays the indoor
temperature by auto sensing through the
temperature sensor.
DO NOT cover the temperature sensor.
Temperature
sensor
Rocker switch of
Nightlight