Excalibur AL-2075-3DB-L User manual

Temporary cover. Final cover is in a separate le.
OPERATION GUIDE
AL-2075-3DB-L
REMOTE START & SECURITY PERFECTED

2
Table Of Contents
Introduction������������������������������������������������������������������������������������������������������������������� 3
Controller & Transmitter Overview�������������������������������������������������������������������������������� 4
The 2-Way Controller ����������������������������������������������������������������������������������������������� 4
The Controller Status Screen ����������������������������������������������������������������������������������� 4
The 1-Way Transmitter ��������������������������������������������������������������������������������������������� 5
Controller & Transmitter Functions������������������������������������������������������������������������������� 5
Other Remote Start Features ������������������������������������������������������������������������������������� 10
Low Voltage & High/Low Temp Automatic Starting������������������������������������������������� 10
Turbo Timer Feature����������������������������������������������������������������������������������������������� 10
Pit-Stop Feature ������������������������������������������������������������������������������������������������������11
Manual Transmission Starting ���������������������������������������������������������������������������������11
Security System Features �������������������������������������������������������������������������������������������11
Last Door Arming�����������������������������������������������������������������������������������������������������11
Automatic Rearming������������������������������������������������������������������������������������������������11
Pre-Warn Detection ������������������������������������������������������������������������������������������������ 12
When The System Triggers������������������������������������������������������������������������������������ 12
Using The Valet Switch����������������������������������������������������������������������������������������������� 12
Emergency Override ���������������������������������������������������������������������������������������������� 12
Valet Mode�������������������������������������������������������������������������������������������������������������� 12
The Status Light ��������������������������������������������������������������������������������������������������������� 13
Multi-Car Operation & Vehicle Proles ����������������������������������������������������������������������� 14
Multi-car Operation������������������������������������������������������������������������������������������������� 14
Programming The Vehicle Image & Name ������������������������������������������������������������� 14
Selecting Vehicle #1 or Vehicle #2 for daily use����������������������������������������������������� 14
Programming Controller Options�������������������������������������������������������������������������������� 15
Button Lock ������������������������������������������������������������������������������������������������������������ 15
Setting The Alarm Clock ����������������������������������������������������������������������������������������� 15
Setting The Clock ��������������������������������������������������������������������������������������������������� 16
Power Save Mode �������������������������������������������������������������������������������������������������� 16
Screen Lighting ������������������������������������������������������������������������������������������������������ 16
Selecting Button Beep�������������������������������������������������������������������������������������������� 17
Selecting Remote Start Melodies ��������������������������������������������������������������������������� 17
Selecting Temperature Display Unit ����������������������������������������������������������������������� 17
Demo Mode������������������������������������������������������������������������������������������������������������ 17
Selecting Melody & Vibrate modes������������������������������������������������������������������������� 17
Parking Timer & Remote Start Timer���������������������������������������������������������������������� 17
Anti-Carjacking Protection������������������������������������������������������������������������������������������ 18
Programming Controllers/Transmitters����������������������������������������������������������������������� 19
Programming Features����������������������������������������������������������������������������������������������� 19
User Programmable Features ������������������������������������������������������������������������������������ 20
Installer Programmable Features ������������������������������������������������������������������������������� 23

3
Introduction
Congratulations for choosing one of the most versatile, fully-featured vehicle secu-
rity and convenience systems available today� Omega Research & Development has
been a leader in vehicle security products for nearly 4 decades� Please take the time
to read this manual thoroughly so you can fully enjoy the benets and features this
system offers�
In this manual, you will primarily learn about 5 user interface components and how
they work together in alerting you to system changes as well as how you can control
system operations� Keep in mind that the operations described in this manual are writ-
ten to only reect the default system settings. Be sure to discuss any customization
with your installer so you can remember any variations from this guide�
Controllers: The system has a 2-way controller that, in addition to controlling the
system, it will give you conrmations on system operations as well as violation alerts.
A 1-way transmitter is also included� It is a standard remote control that still gives
you control over all features but without conrmations. The next section covers the
controllers’ operations in detail�
The Status Lights: These lights are built into the system’s window-mounted
antenna� They give you a visual indication of the system’s current state and provide
troubleshooting indicators� The operations of the status lights are covered later in this
manual�
The Valet Switch: This push button gives you access to system programming,
transmitter/controller programming, and valet functions� It is also built into the sys-
tem’s window-mounted antenna� The valet switch’s operations are also covered later
in this manual�
Flashing Lights: The system is connected to your vehicle’s parking lights to
provide a 360 degree visual conrmation, warning, & deterrence in almost all system
operations� Each operation described in this manual also includes the corresponding
indicator from the ashing lights. The ashing lights primarily provide visual deter-
rence when the system is violated�
Siren and/or Horn Sounding: The system includes an electronic siren that offers
conrmation chirps during daily operations and programming. It is also the primary
means of alerting anyone near your vehicle that the system has been violated� The
system is capable of sounding the vehicle’s horn in addition to, or in place of, the
electronic siren� Most system functions have a corresponding audible alert that is
described throughout this manual� Becoming familiar with these alerts will help you to
instantly understand any changes in the system’s status�

4
THE 2-WAY CONTROLLER
Controller & Transmitter Overview
Controller part number: 1512-03
1) Antenna: Sends commands to the system and
receives conrmations for 2-way functions.
2) OLED Display: Displays all controller functions
as well as the status of your system�
3) Backlit Buttons: Flashes while transmitting and
indicates battery charging status�
4) Control Buttons: These are the primary use
buttons LOCK, UNLOCK, TRUNK, & START� They
are also used to navigate the controller’s options�
5) Charger Port: This is where you plug in the
charger to recharge the controller’s battery�
6) Programming Button: This is used for setting
controller features and many other functions� See
“programming controller options” on page 15�
Battery Level Indicator*
Clock/Timer
Current System State
Vehicle Image
(Selectable)
Alarm Clock ON icon
Vehicle Name
(Programmable)
Melody Indicator
Vibration Mode Indicator
Lock/Unlock Indicator
2-way In Range
Indicator
*The controller is powered by a built-in rechargeable battery� When the battery level
indicator shows a low battery, plug the supplied USB cable into the controller, then
connect the other end to the supplied AC adapter, car adapter, or your computer’s
USB port. While charging, the indicator will ash from empty to full and the backlit
buttons will ash once every 5 seconds while charging. When full, the indicator will be
solid green and the backlit buttons will stay illuminated�
THE CONTROLLER STATUS SCREEN
6
1
4
5
2
3
4

5
Controller & Transmitter Overview (cont’d)
LOCK
button
TRUNK
button
UNLOCK
button
START
button
Range
boost
Part number: 1513-03 E
Call your dealer or visit www.caralarm.com to
order replacement transmitters.
Transmitter battery replacement:
Remove the small screw from the lower
back case, and separate the transmitter
halves� Replace the battery and reas-
semble the transmitter case�
Battery Types:
1513-03E - CR2025 (2 required)
THE 1-WAY TRANSMITTER
Controller & Transmitter Functions
LOCK / ARM: Press and release the LOCK button�
• THE SIREN WILL CHIRP & THE PARKING LIGHTS WILL
FLASH ONCE�
• UPON RECEIVING CONFIRMATION FROM YOUR
SYSTEM, THE CONTROLLER WILL PLAY THE LOCK/ARM
ANIMATION AND BEEP ONCE
NOTE: PRESSING LOCK TWICE IN 5 SECONDS STARTS
THE PARKING TIMER. THE CLOCK WILL CHANGE TO
0:00 AND START COUNTING IN MINUTES & HOURS.
(1-WAY TRANSMITTER: PRESS THE LOCK BUTTON)
UNLOCK / DISARM: Press and release the UNLOCK button�
• THE SIREN WILL CHIRP TWICE & THE PARKING
LIGHTS WILL FLASH TWICE THEN ILLUMINATE FOR 30
SECONDS�
• UPON RECEIVING CONFIRMATION FROM YOUR
SYSTEM, THE CONTROLLER WILL PLAY THE UNLOCK/
DISARM ANIMATION AND BEEP TWICE�
(1-WAY TRANSMITTER: PRESS THE UNLOCK BUTTON)
NOTE: The 2-way Controller is shipped from the factory in POWER OFF mode.
If you connect the charger before powering it, perform POWER OFF, then
POWER ON again.
POWER ON: Press and hold the “P” button for at least 1 second
POWER OFF: Press the “P” and START buttons for at least 1 second

6
Controller & Transmitter Functions (cont’d)
TRUNK RELEASE / CHANNEL 2: Press the TRUNK button for 3
seconds�
• THE SYSTEM WILL DISARM AND THE TRUNK WILL
OPEN (IF EQUIPPED)�
• UPON RECEIVING CONFIRMATION FROM YOUR
SYSTEM, THE CONTROLLER WILL PLAY THE TRUNK
RELEASE ANIMATION AND BEEP TWICE
(1-WAY TRANSMITTER: PRESS AND HOLD THE TRUNK
BUTTON FOR 3 SECONDS)
REMOTE START: Press and release the START button twice within
5 seconds� (see user feature #8 for additional options)
• THE PARKING LIGHTS WILL FLASH ONCE AND THE
STATUS LIGHT WILL FLASH RAPIDLY�
• THE SYSTEM WILL TURN ON THE IGNITIONS AND
PROCEED TO START THE ENGINE�
• ONCE THE ENGINE IS RUNNING, THE PARKING
LIGHTS WILL FLASH AND THE STATUS LIGHTS WILL
FLASH SLOWLY�
• UPON RECEIVING CONFIRMATION FROM YOUR
SYSTEM, THE CONTROLLER WILL PLAY THE REMOTE
START ANIMATION AND PLAY A MELODY�
• THE CLOCK WILL CHANGE TO 0:00 TO START THE
REMOTE START TIMER� IT WILL TIME HOW LONG THE
ENGINE RUNS IN MINUTES & HOURS�
(1-WAY TRANSMITTER: PRESS THE START BUTTON
TWICE IN 5 SECONDS)
• If the engine stalls, the system will make up to 3 more attempts�
• Each time you park your vehicle, set the climate controls to give you the de-
sired interior temperature when you use the remote start�
The engine will run for the preset run time (see user feature #1)�
• Run Time Extender: Press the START button one time while in remote start
mode to restart the engine run timer� The timer on the controller will restart at
“0:00”�
NOTE: This can only be used once per remote start cycle. The controller will also give you
“run time expiration” warning (2 chirps) 1 minute before the remote start cycle ends.
• If you decide not to drive your vehicle, you can turn off the remote start using
the same method to turn it on (Default = press START twice in 5 seconds)
NOTE: If user feature #8 is programmed for 1 press, the 1st press = Run Time Extender so
an additional press is required.
• Upon entering the vehicle during remote start mode, turn the ignition key to
the “ON/RUN” position (NOT START!!)� When you press the brake pedal, the
remote start will turn off allowing the ignition key to take over�
x2

7
Controller & Transmitter Functions (cont’d)
CHANNEL 3: Press P then TRUNK within 5 seconds�
• YOUR SYSTEM WILL ACTIVATE THE CHANNEL 3
OUTPUT�
• UPON RECEIVING CONFIRMATION FROM YOUR
SYSTEM, THE CONTROLLER WILL PLAY THE CHANNEL
3 ANIMATION�
(1-WAY TRANSMITTER: PRESS AND HOLD THE TRUNK
& START BUTTONS FOR 1 SECOND)
CHANNEL 4: Press P twice then TRUNK within 5 seconds�
• YOUR SYSTEM WILL ACTIVATE THE CHANNEL 4
OUTPUT�
• UPON RECEIVING CONFIRMATION FROM YOUR
SYSTEM, THE CONTROLLER WILL PLAY THE CHANNEL
4 ANIMATION�
(1-WAY TRANSMITTER: PRESS THE LOCK & TRUNK
BUTTONS FOR 1 SECOND)
CHANNEL 5: Press P three times then TRUNK within 5 seconds�
• YOUR SYSTEM WILL ACTIVATE THE CHANNEL 5
OUTPUT�
• UPON RECEIVING CONFIRMATION FROM YOUR
SYSTEM, THE CONTROLLER WILL PLAY THE CHANNEL
5 ANIMATION�
(1-WAY TRANSMITTER: PRESS THE UNLOCK & START
BUTTONS FOR 1 SECOND)
• THE SYSTEM WILL ENTER VALET MODE�
SEE PAGE 12 FOR MORE INFO ON VALET MODE�
(1-WAY TRANSMITTER: PRESS LOCK, UNLOCK,
TRUNK+START)
3
3
3
4
REMOTE VALET: Press LOCK then UNLOCK then TRUNK +
START within 5 seconds�
1
1
1
1
2
2
2
2
3

8
PANIC: Press and hold the LOCK or UNLOCK button for 3
seconds�
• THE SIREN/HORN WILL SOUND, THE PARKING
LIGHTS WILL FLASH, AND THE DOORS WILL LOCK OR
UNLOCK DEPENDING WHICH BUTTON IS PRESSED�
(1-WAY TRANSMITTER: PRESS AND HOLD THE LOCK
OR UNLOCK BUTTON FOR 3 SECONDS)
Controller & Transmitter Functions (cont’d)
SILENT ARM / DISARM: Press and release the TRUNK button
twice in 5 seconds�
LOCK W/O ARM: Press TRUNK then LOCK within 5 seconds�
• THE PARKING LIGHTS WILL FLASH, AND THE
DOORS WILL LOCK/ARM OR UNLOCK/DISARM DE-
PENDING ON THE CURRENT SYSTEM STATUS�
• UPON RECEIVING CONFIRMATION FROM YOUR
SYSTEM, THE CONTROLLER WILL PLAY THE LOCK/
ARM OR UNLOCK/DISARM ANIMATION�
(1-WAY TRANSMITTER: PRESS RELEASE THE TRUNK
BUTTON TWICE IN 5 SECONDS)
• THE DOORS WILL LOCK WITHOUT ARMING THE
ALARM� IDEAL FOR RV OCCUPANTS, PETS, ETC�
• UPON RECEIVING CONFIRMATION FROM YOUR
SYSTEM, THE CONTROLLER WILL PLAY THE LOCK
ANIMATION�
(1-WAY TRANSMITTER: PRESS TRUNK THEN LOCK
WITHIN 5 SECONDS)
SENSOR BYPASS: Press and release the TRUNK button within 5
seconds of locking/arming the alarm system�
• THE SYSTEM WILL GIVE ONE CHIRP TO INDICATE
THE SENSOR IS BYPASSED�
• UPON RECEIVING CONFIRMATION FROM YOUR
SYSTEM, THE CONTROLLER WILL PLAY THE SENSOR
BYPASS ANIMATION AND CHIRP ONCE�
(1-WAY TRANSMITTER: PRESS AND RELEASE THE
TRUNK BUTTON WITHIN 5 SECONDS OF ARMING THE
SYSTEM)
OR
1
1
2
x2
2
1

9
AUXILIARY FUNCTIONS 1-4:
The actual operation of these functions will vary from car to car� They are designed
to operate extra vehicle functions like automatic sliding doors or motorized hatches.
Aux 1-4 are virtual outputs only available on certain vehicles when this system is
integrated with the vehicle’s data network. Consult your installer to nd out if any of
these functions are available for your vehicle. If so, conrm each operation with the
controller and write each function in the blank spaces provided below�
- Auxiliary 1 Function (___________________): To activate this function, press
and release the TRUNK and START buttons simultaneously (or P then TRUNK)�
- Auxiliary 2 Function (___________________): To activate this function, press
and release the LOCK and TRUNK buttons simultaneously (or P x2 then TRUNK).
- Auxiliary 3 Function (___________________): To activate this function, press
and release the UNLOCK and START buttons simultaneously (or P x3 then TRUNK).
- Auxiliary 4 Function (___________________): To activate this function,
press and release the UNLOCK and TRUNK buttons simultaneously�
Controller & Transmitter Functions (cont’d)
1
1
2
2
LOW VOLTAGE & HIGH/LOW TEMP AUTO START: Press
UNLOCK, LOCK, START within 5 seconds�
• THE SYSTEM WILL GIVE ONE CHIRP TO INDICATE
THE LOW VOLT/LOW TEMP(15 DEGREE ONLY) AUTO-
START IS ACTIVATED� SEE PAGE 9 FOR MORE INFO�
• UPON RECEIVING CONFIRMATION, THE CONTROL-
LER WILL CHIRP ONCE AND THE STATUS WILL READ
“RS AUTO” EVERY 5 SECONDS�
(1-WAY TRANSMITTER: PRESS AND RELEASE THE
START BUTTON WITHIN 5 SECONDS OF ARMING THE
SYSTEM)
3
2
1
VEHICLE TEMP REQUEST: Press and release “P” then START
within 5 seconds� • UPON RECEIVING CONFIRMATION, THE
CONTROLLER WILL PLAY A MELODY AND THE
CLOCK WILL DISPLAY THE VEHICLE’S INTERIOR
TEMPERATURE�
• IF THE TEMP IS BELOW 40°F(4°C) OR ABOVE
90°F(32°C), THE CLOCK WILL ALSO READ “RS
RCMD” (REMOTE START RECOMMENDED)
LOCK/UNLOCK STATUS UPDATE REQUEST: Press and release
“P” then LOCK within 5 seconds�
• THE SYSTEM WILL SEND A FULL STATUS
UPDATE TO THE CONTROLLER IN CASE THE
STATUS CHANGED WHILE THE CONTROLLER
WAS OUT OF RANGE�
• THERE IS NO AUDIBLE INDICATION FOR THIS
FUNCTION�

10
Other Remote Start Features
It is typically recommended that vehicles equipped with turbocharged engines allow
the engine to idle for after driving to cool the turbocharger� When this Installer Pro-
grammable Feature (#10) is enabled, the system will automatically keep the engine
running as follows:
• With the engine running, hold the brake pedal and engage the parking
brake� When the brake pedal is released, the system will keep the engine running for
the programmed time (1, 2, or 3 minutes), and then automatically turn it off�
• The system may be locked while the engine is running� Turbo Timer can be
prevented from engaging, or “bypassed” if desired, by turning the engine off before
engaging the parking brake, or if it’s already engaged, step on the brake pedal to turn
the engine off�
TURBO TIMER FEATURE
LOW VOLTAGE & HIGH/LOW TEMP AUTOMATIC STARTING
This feature will automatically start the engine if the vehicle battery drops below
11�5 volts or the interior temperature goes above or below the pre-programmed
threshold�
Programming The Low Temperature Auto Start Threshold:
• Turn the ignition switch “on”, then “off” (engine not running), and within 5 seconds
press the valet switch twice� The siren will chirp 3 times, within 5 seconds press the
valet switch equal to the desired low temperature remote start threshold�
1 press = 0 degrees F - 1 chirp conrmation
2 presses = 15 degrees F - 2 chirps conrmation
3 presses = 32 degrees F - 3 chirps conrmation
Programming The High Temperature Auto Start Threshold:
• Turn the ignition switch “on”, then “off” (engine not running), and within 5 seconds
press the valet switch three times� The siren will chirp 4 times, within 5 seconds
press the valet switch equal to the desired high temperature remote start threshold�
1 press = 75 degrees F - 1 chirp conrmation
2 presses = 90 degrees F - 2 chirps conrmation
3 presses = 105 degrees F - 3 chirps conrmation
4 presses = 120 degrees F - 4 chirps conrmation
Activation Using The Valet Switch
• Turn the ignition switch “on”, then “off” (engine not running), and within 5 seconds
press the valet switch twice� After a 2 second delay without additional valet button
presses, the siren will chirp 3 times activating low battery & low/high temp auto start�
Activation Using The Controller
• Within 5 seconds, press UNLOCK, LOCK, START� The siren/horn will chirp to
conrm.
These features will operate once every two hours until the ignition key is turned “ON”�
• You must activate this features each time you park your car to use them�

11
PIT-STOP FEATURE
This feature allows you to leave your engine running for quick errands� To use this
feature, have the engine running normally from the ignition switch and your foot off
the brake pedal. Press the Valet Switch twice; the parking lights will ash to conrm.
Turn the key off and the engine will remain running for the programmed run time�
XL PIT STOP: Press the Valet Switch 6 times instead of 2 & the engine will run for 12
hours� Ideal for commercial applications such as refrigeration & cleaning vehicles�
LAST DOOR ARMING
See user feature #9� When this feature is enabled, the siren/horn will chirp once
when all of the doors are closed� It will then start a 30 second countdown (fast
ashing status light). After 30 seconds, the system will arm. During the 30 second
arming delay, if a point of entry is opened, the countdown will pause until all entry
points are closed again� Turning ON the ignition key will cancel the last door arming
sequence until the key is turned off and the doors are all closed once again�
AUTOMATIC REARMING
This automatically rearms the alarm if the system is disarmed from the remote�
(see user feature #10 to enable)� When disarmed by remote, the system will start a
90 second countdown (fast ashing status light) to arm the system. This is useful if
the controller may accidentally disarms the system when it’s kept in a purse or pocket
where other items could potentially press the buttons� ENHANCED AUTO REARM
allows you to cancel the countdown by pressing UNLOCK a second time within
5 seconds of the rst press to disarm the alarm.
Security System Features
MANUAL TRANSMISSION STARTING
Remote starting with a manual transmission requires that you ensure the gear
selector is in NEUTRAL� There are 2 available methods�
METHOD #1 - 3D MOTION SENSOR:
This system is equipped with a 3D motion sensor built into the antenna� Whenever
remote start is activated, the sensor is monitored for vehicle movement� If the vehicle
moves just a few inches when the engine is cranking, it will instantly turn the engine
off� This safety feature allows you to enjoy remote start without performing reservation
mode as described below�
METHOD #2 - RESERVATION MODE:
For extra safety, installer feature #11 can be turned on which requires you to perform
a setup procedure that ensures the transmission was left in neutral when you park
your vehicle� This must be performed each time you leave your vehicle to use remote
start later� To do so, follow these steps:
1) With the engine running via the ignition switch, hold the brake pedal, apply the
parking brake, then release the brake pedal�
2) Use the transmitter as if you were activating remote start (default: press START
twice). The status light will start to ash slow.
3) Turn off the ignition key and exit the vehicle, the engine will continue running.
4) Press LOCK on the transmitter� The engine will shut down (unless turbo timer is
on) and the status light will ash every 2 seconds (ready to be remote started).
NOTE: Manual transmission starting is canceled if you enter the vehicle after
performing the setup procedure.
Other Remote Start Features (cont’d)

12
Using The Valet Switch
VALET MODE
Valet mode completely disables all security & remote start functions� Keyless entry
is still operable� To enter valet mode, perform the following steps:
STEP 1 - Disarm the system by remote or by performing an emergency override�
STEP 2 - Press and hold the valet switch for 2 seconds� The system will chirp once
and the status light will turn on�
EXITING VALET MODE - Press and release the valet switch once� The status light
will turn off�
EMERGENCY OVERRIDE
If you were to lose or break your controller, you’d need to perform an emergency
override to disarm the system and use your vehicle� To do so, use the following steps:
STEP 1 - Enter the vehicle (the alarm should sound)�
STEP 2 - Turn the ignition key to the “ON” position�
STEP 3 - Press the valet switch (located in the window-mount antenna) once�
NOTE: Enter your SecureCode at this time if programmed via user feature #13
STEP 4 - Turn the ignition key “OFF”�
WHEN THE SYSTEM TRIGGERS
It will sound the siren/horn and ash the parking lights for 30 seconds (selectable).
The controller will also alert you indicating which zone is violated (if in range of the
system)� When disarming the system after a trigger event, the siren/horn will chirp
and the lights will ash 4 times instead of the standard 2 times.
LOCK ON TRIGGER: If a door is opened when the system is triggered, it will wait
until the door is closed again, then lock the doors�
STORM SAFE MODE: When the system is triggered, pressing the UNLOCK button
will stop the alarm from sounding but will leave the doors locked� This function is use-
ful if you have a false triggering situation due to violent weather�
ZONE VIOLATION RECALL: The system is capable of telling you which zones were
triggered last. The system’s status light will ash to indicate which zone was triggered
(see the next page). This occurs during the alarm cycle AND after disarming. The
system will store the last triggered zone until the vehicle’s ignition key is turned on.
NUISANCE PREVENTION: If the sensor prewarns 5 times within 15 minutes, it will
bypass the zone for the remainder of the 15 minutes before rearming the pre-warn
zone. If a full trigger zone is left open, the system will trigger a total of 3 times before
bypassing the zone. Once the zone is closed again, it will re-arm that zone.
PRE-WARN DETECTION
This system’s impact sensor is designed, in addition to detecting a full impact, to
warn away potential violators when it detects a light impact to the vehicle� The system
will respond by chirping the siren/horn 3 times and locking the doors� This is very use-
ful when an intruder attempts to unlock the door with “slim jim” types of devices�
Security System Features (cont’d)

13
The Status Light
The status light, located in the antenna, indicates the system’s current status�
SECURITY SYSTEM STATUS
OFF: The alarm is disarmed and not performing any automatic functions�
ON: The alarm is in valet mode�
FLASHING SLOW: The alarm is armed and monitoring all entry points�
FLASHING FAST: One of the automatic arming features is in progress�
AUTOMATIC TRANSMITTER VERIFICATION
Every time you turn on the ignition key, the status light will ash a number of times
equal to the number of transmitters programmed to the system� This unique security
feature combats potential thieves (valet attendant, mechanic, etc�) from adding their
own transmitter without your knowledge and accessing your vehicle at a later time�
ALARM ZONE VIOLATION RECALL
If the security system is triggered, upon disarming, the status light will ash
a number of times to indicate exactly which zone(s), has been violated. It will
store the last 2 violated circuits and continually repeat the ash pattern until the
vehicle’s ignition key is turned ON�
2 FLASHES: Hood trigger
3 FLASHES: Door trigger
4 FLASHES: Sensor port trigger
REMOTE START STATUS
FLASHING SLOW: The engine was remote started successfully and is running�
FLASHING FAST: The remote start sequence has begun and is in process of
starting�
2 FLASHES, PAUSE: The engine is running while the alarm is armed�
REMOTE START DIAGNOSTICS
The remote start system can also indicate which zone caused the last remote
start cycle to end� To see this indicator, place the system into alarm valet mode�
Immediately after the chirp, the status light will ash to indicate which zone violation
occurred�
1 FLASH: The hood was opened�
2 FLASHES: Brake pedal was pressed
3 FLASHES: Bad tach signal or engine overrev�
4 FLASHES: The neutral safety circuit was triggered�
5 FLASHES: The 3D sensor detected vehicle motion�
6 FLASHES: Received command to stop�
7 FLASHES: The alarm was triggered�
8 FLASHES: Run time expired.
9 FLASHES: Low battery voltage was detected�

14
Multi-Car Operation & Vehicle Proles
MULTI-CAR OPERATION
The controller can operate up to 2 different systems� When controlling 2 systems, it
will receive all status updates on the currently selected vehicle prole and will receive
only trigger alerts for the 2nd vehicle� You can switch from one car to the other at any-
time as well as choose a unique image and name for each vehicle� Use the following
steps to change vehicle proles as well as select the vehicle image and name.
1) Press the “P” button for 3 seconds to access options�
2) Scroll down until “Vehicle Info” is highlighted
(pictured to the left above)�
3) Press the 4button to select�
4) Scroll to highlight Vehicle #1 or Vehicle #2
5) Press the 4button to select�
6) The image option will be highlighted� Scroll up or down to
change the image� (pictured to the left)
7) Press the 4button to select�
8) The rst letter of the name is highlighted. Use the up and
down arrows to scroll through the alphabet/numbers� Press
the 4 button to move to the next space. Press to move
back a space� The name can be up to 8 characters�
PROGRAMMING THE VEHICLE IMAGE & NAME
SELECTING VEHICLE #1 OR VEHICLE #2 FOR DAILY USE
Press the “P” then UNLOCK select Vehicle #1� The controller will beep/vibrate once�
Repeat to select Vehicle #2� The controller will beep/vibrate twice�
Scroll
Up
Programming Controls
Return To
Previous Screen
Select Highlighted
Option
Scroll
Down
After selecting the 8th character, you will return to the Vehicle #1/#2 selection screen�
Press the “P” button to return to status screen or press the button to return to the
main menu�
- Press for 3 seconds to access the options menu.
- Press and release to return to the status screen.

15
Programming Controller Options
Scroll Up
Programming Controls
Return To
Previous Screen
Select Highlighted
Option
Scroll Down
- Press for 3 seconds to access the options menu.
- Press and release to return to the status screen.
Each function button on the controller also serves for navigating through the option
menus and making changes to the controller options� These secondary functions are
indicated by small icons in the upper corners of each button. See below for an expla-
nation of each button’s function�
BUTTON LOCK
This feature disables the function buttons from operating
when pressed� This prevents accidental system activation�
To activate:
1) Press the “P” button to access the options menu�
2) “Button Lock” will be highlighted by default�
3) Press the 4button to select� All function buttons are
now locked�
3) To unlock the buttons, press START then UNLOCK�
*
SETTING THE ALARM CLOCK
1) Press the “P” button to access the options menu�
2) Scroll down until “Alarm Clock” is highlighted
3) Press the 4button to select�
4) Scroll down to highlight ON�*
5) Press the 4button to select�
6) The hour will now be highlighted� Scroll to select the
desired hour�
7) Press the 4button to select�
6) The hour digits will now be highlighted� Scroll to select
the desired hour�
8) Press the 4button to select�
9) The minute digits will now be highlighted� Scroll to select
the desired minute setting�
10) Press the 4button to select�
END HERE IF CLOCK IS IN 24 HOUR FORMAT
11) AM/PM will now be highlighted�** Scroll to select the
desired setting�
12) Press the 4button to select�
*To disable, perform
steps 1-5 but select
OFF on step 4
**The alarm clock has
an optional 24 hour
format (see “setting
the clock”)

16
Programming Controller Options (cont’d)
This option selects how long the screen will stay lit
before turning back off� Keep in mind that longer settings
sacrice some battery life. To program:
1) Press the “P” button to access the options menu�
2) Scroll down until “Screen Lighting” is highlighted
3) Press the 4button to select�
4) Scroll to select the desired time interval�
3) Press the 4button to select�
SCREEN LIGHTING
The 2-way portion of the controller can be disabled com-
pletely to save battery life while traveling or out of range of
the vehicle� To set power save:
1) Press the “P” button to access the options menu�
2) Scroll down until “Power Save” is highlighted
3) Press the 4button to select�
4) Scroll to select ON or OFF, whichever is desired�
3) Press the 4button to select�
When Power Save mode is ON, you will not receive any
2-way conrmations. Additionally, there will be a red X over
the “in range” indicator in the lower left corner of the status
screen (pictured to the left)�
POWER SAVE MODE
SETTING THE CLOCK
1) Press the “P” button to access the options menu�
2) Scroll down until “Set Clock” is highlighted
3) Press the 4button to select�
4) Scroll to highlight either 12 (AM/PM) or 24 hour format�
5) Press the 4button to select� (the hour is highlighted)
6) Scroll to select the desired hour�
7) Press the 4button to select� (the hour is highlighted)
6) The hour digits will now be highlighted� Scroll to select
the desired hour�
8) Press the 4button to select�
9) The minute digits will now be highlighted� Scroll to the desired minute setting�
10) Press the 4button to select�
END HERE IF CLOCK IS IN 24 HOUR FORMAT
11) AM/PM will now be highlighted� Scroll to select the desired setting�
12) Press the 4button to select�

17
DEMO MODE
Demo mode will show you a demonstration movie of all the controller’s conrma-
tion animations and alerts� To view demo mode, use the following steps�
1) Press the “P” button for 3 seconds to access options�
2) Scroll down until “DEMO” is highlighted
3) Press the 4button to select�
Programming Controller Options (cont’d)
PARKING TIMER: Press LOCK twice within 5 secondsto start the timer�
REMOTE START TIMER: This turns on every time you remote start�
Note: Pressing the “P” during either timer mode will switch between the
timer and clock.
PARKING TIMER & REMOTE START TIMER
SELECTING BUTTON BEEP
With this option turned ON, the controller will beep to con-
rm each button press. The default setting is OFF. To turn
ON/OFF, use the following procedure:
1) Press the “P” button for 3 seconds to access options�
2) Scroll down until “Button Beep” is highlighted
3) Press the 4button to select�
4) Scroll up or down to highlight the desired setting�
5) Press the 4button to select�
SELECTING MELODY & VIBRATE MODES
The controller can give you 2-way alerts with a melody, vibration, or both� By
default, the controller is set for melody only� Press the “P” and trunk buttons
simultaneously for 2 seconds to change the setting. The sequence is VIBRATE
only, MELODY + VIBRATE, MELODY only� The melody and vibrate icons at the top of
the status screen will change to indicate your selection�
This option allows you to select from 5 different melodies to
indicate when remote start is turned on and off� To change
the setting, use the following procedure:
1) Press the “P” button for 3 seconds to access options�
2) Scroll down until “Melodies” is highlighted
3) Press the 4button to select�
4) Scroll up or down to highlight the desired setting�
5) Press the 4button to select�
This option allows you to select Farhenheit or Celsius for the temperature display:
1) Press the “P” button for 3 seconds to access options�
2) Scroll down until “Temp Display” is highlighted
3) Press the 4button to select�
4) Scroll up or down to highlight the desired setting�
5) Press the 4button to select�
SELECTING REMOTE START MELODIES
SELECTING TEMPERATURE DISPLAY UNIT

18
Anti-Carjacking Protection
The system is equipped with two separate Anti-Carjacking protection features (igni-
tion, open door, or both)� All are programmable, and must be turned on to operate�
Once activated, the user has 60 seconds to cancel the Anti-Carjacking protection
process (described below)� If Anti-Carjacking is not cancelled, 53 seconds after being
activated the siren will begin to chirp for 7 seconds to alert the user that the system
is about to enter into an alarm condition� The Valet Switch may still be pressed once
during this period to cancel the Anti-Carjacking process�
If the Anti-Carjacking process is not cancelled before the 60 second countdown
expires, the system will enter an alarm condition, sounding the siren and ashing the
parking lights� 30 seconds after this occurs, or should the ignition be turned off in the
meantime, the stater interrupt will engage� Once the system enters the alarm condi-
tion, it will not respond to the transmitter, nor will the system reset automatically after
60 seconds, and it can only be disengaged by:
Step 1 Turning the vehicle’s ignition off�
Step 2 Turning the ignition back on�
Step 3 Within 5 seconds, perform an Emergency Override using the Valet Switch� If
the SecureCode has been customized, the correct number of Valet Switch presses
must be made�
The different types of Anti-Carjacking protection are:
Ignition Activated Anti-Carjacking activates every time the vehicle’s ignition is
turned on� The Valet Switch must be pressed within 60 seconds of activating to can-
cel Anti-Carjacking� This is User Programmable Feature #12�
Door Anti-Carjacking activates when a door is opened after the vehicle is started
and the engine is running� The Valet Switch must be pressed within 60 seconds after
activation to cancel Anti-Carjacking� This is User Programmable Feature #12�

19
Step 1 Turn the ignition key “ON”, then “OFF”�
Step 2 Within 5 seconds of step 1, press the valet switch 5 times to access user
features (10 times to access installer features)�
~ The siren/horn will sound and the status light will turn on�
Step 3 Within 10 seconds of step 2, press the valet switch the number of times cor-
responding with the desired feature’s number�
~ The siren/horn will chirp, the status lights, and the parking lights will ash equal
to the selected feature�
Step 4 Change the feature by pressing the transmitter button that corresponds with
the desired setting� The siren/horn will chirp to correspond with the chosen setting�
Programming Features
Standard Programming: Use this method to program additional or replacement
transmitters� Before you begin, have all transmitters at hand and make sure the cor-
rect vehicle prole (see page 12) is selected on the controller(s).
Step 1 Then, turn the ignition “on”�
Step 2 Within 5 seconds of Step 1, press the Valet Switch 5 times� The siren/horn will
briey sound, conrming that the system is ready to learn a transmitter code.
Step 3 Press the LOCK button on each transmitter one at a time� The system will
chirp the siren/horn once to conrm that each was learned. If a code is not received
within 10 seconds of Step 2, the learning process will automatically exit.
Programming Controllers/Transmitters

20
User Programmable Features
Feature #5 - Ignition Controlled Lock/Unlock
Off (press LOCK to program)
Lock w/ Ignition On (press UNLOCK to program)
Unlock w/ Ignition Off (press TRUNK to program)
Lock And Unlock w/ Ignition (press START to program)
This feature controls the lock/unlock operations when the ignition key is turned on/off�
Feature #1 - Remote Start Run Time
3 Minutes (press LOCK to program)
10 Minutes (press UNLOCK to program)
15 Minutes (press TRUNK to program)
20 Minutes (press START to program)
30 Minutes (press LOCK & UNLOCK to program)
This sets the maximum amount of time that the remote start will keep the engine
running if it is not shut down by other methods�
Feature #3 - Conrmation Chirp Volume
Low (softest) (press LOCK to program)
Medium Low (press UNLOCK to program)
Medium High (press TRUNK to program)
High (loudest) (press START to program)
This feature allows the choice different chirp volume levels, and when programming
it, each selection will be conrmed in the chosen volume making it easy to choose the
most suitable setting�
Feature #2 - Flashing Light Conrmations
Unlock: ON, RS: ON (press LOCK to program)
Unlock: ON, RS: Flash (press UNLOCK to program)
Unlock: Flash, RS: ON (press TRUNK to program)
Unlock: Flash, RS: Flash(press START to program)
This feature affects the parking light conrmations for system unlock & remote start
functions� With the above options, you can select any combination of:
Unlock: Flash - Flashes twice after unlock
Unlock: ON - Flashes twice then stays on for 30 seconds after unlock
RS: ON - Stays on during remote start mode
RS: Flash - Flashes once every 1�5 seconds during remote start mode
Feature #4 - BROWN Wire Audible Output
Pulsed Horn Low (press LOCK to program)
Pulsed Horn Medium (press UNLOCK to program)
Pulsed Horn High (press TRUNK to program)
Steady Siren (press START to program)
Random (press LOCK & UNLOCK to program)
This changes the BROWN wire’s audible output when the alarm is triggered� Steady
siren must be selected when using a siren (other horn outputs stay at the Medium
setting)� The random option will pulse the horn in a distinct long and short honk
routine during the alarm trigger condition� The horn honk options will affect all horn
honk outputs used as well as change the BROWN wire’s function� If installer feature
#6 is set to “Horn” the Brown wire will function as a steady siren when “Random” is
selected�