Excalibur RS-360-EDP User manual

RS-360-EDP / RS-360-EDP+
Deluxe Keyless Entry & Remote Start
Operation Guide
July 7, 2014
Temporary cover. Color cover is in a separate le.
1

Table Of Contents
Transmitter Overview ��������������������������������������������������������������������������������������������������� 3
Transmitter Functions��������������������������������������������������������������������������������������������������� 3
Other Remote Start Features ��������������������������������������������������������������������������������������� 6
Low Battery/Low Temp Automatic Starting��������������������������������������������������������������� 6
Turbo Timer Feature������������������������������������������������������������������������������������������������� 6
Pit-Stop Feature ������������������������������������������������������������������������������������������������������� 6
Manual Transmission Starting ���������������������������������������������������������������������������������� 7
Security System Features (OPTIONAL)����������������������������������������������������������������������� 7
Last Door Arming������������������������������������������������������������������������������������������������������ 7
Automatic Rearming������������������������������������������������������������������������������������������������� 7
Pre-Warn Detection �������������������������������������������������������������������������������������������������� 7
When The System Triggers�������������������������������������������������������������������������������������� 8
Using The Valet Switch������������������������������������������������������������������������������������������������� 8
Emergency Override ������������������������������������������������������������������������������������������������ 8
Valet Mode���������������������������������������������������������������������������������������������������������������� 8
SecureCode ������������������������������������������������������������������������������������������������������������� 9
The Status Light ����������������������������������������������������������������������������������������������������������� 9
Anti-Carjacking Protection������������������������������������������������������������������������������������������ 10
Programming Transmitters ������������������������������������������������������������������������������������������11
Programming Features������������������������������������������������������������������������������������������������11
User Programmable Features ������������������������������������������������������������������������������������ 12
Installer Programmable Features ������������������������������������������������������������������������������� 15
Programmable Features Matrix���������������������������������������������������������������������������������� 19
This device complies with FCC Rules part 15� Operation is subject to the following
two conditions, (1) This device may not cause harmful interference and, (2) This
device must accept any interference that may be received, including interference
that may cause undesired operation�
The manufacturer is not responsible for any radio or TV interference caused by
unauthorized modications to this equipment. Such modications could void the
user’s authority to operate the equipment.
2

Transmitter Overview
LOCK: Press and release the “LOCK” button�
• THE PARKING LIGHTS WILL FLASH ONCE�
• IF SECURITY IS ENABLED, THE SIREN / HORN WILL
CHIRP�
Transmitter Functions
UNLOCK: Press and release the “UNLOCK” button�
• THE PARKING LIGHTS WILL FLASH TWICE, THEN IL-
LUMINATE FOR 30 SECONDS�
• IF SECURITY IS ENABLED, THE SIREN / HORN WILL
CHIRP TWICE�
“lock”
button
“start”
button
“unlock”
button
“trunk”
button
Transmitter part number:
1411-03
Call your dealer or visit
www.caralarm.com to order
replacement transmitters.
Battery replacement:
Remove the small screw from the
lower back case, and separate the
transmitter halves� Replace the
CR2032 battery (or with 2 CR2016
batteries) and reassemble the
transmitter case�
This system is ECHO compatible, which means you can upgrade at anytime to
have 2-way capability and greater range (up to 1-mile!). It’s a simple upgrade
that only takes minutes, so talk to your dealer about upgrading with ECHO
TECHNOLOGY today!!
3

Transmitter Functions (cont’d)
TRUNK RELEASE / CHANNEL 2: Press the “TRUNK” button for 3
seconds�
• THE SYSTEM WILL DISARM / UNLOCK AND THE
TRUNK WILL OPEN (IF EQUIPPED)�
REMOTE START: Press and release the “START” button twice
within 5 seconds� (see user feature #8 for additional options)
• THE PARKING LIGHTS WILL FLASH ONCE AND THE
STATUS LIGHT WILL FLASH RAPIDLY�
• THE SYSTEM WILL TURN ON THE IGNITIONS AND
PROCEED TO START THE ENGINE�
• ONCE THE ENGINE IS RUNNING, THE PARKING
LIGHTS WILL TURN ON AND STAY ON AND THE
STATUS LIGHTS WILL FLASH SLOWLY�
• If the engine stalls, the system will make up to 3 more attempts�
• Each time you park, set the climate controls as desired when you use the remote start� The
engine will run for the preset run time (see user feature #1)�
• Run Time Extender: Press the “START” button one time during remote start to restart the
engine run timer�
NOTE: This can only be used once per remote start cycle.
• If you decide not to drive your vehicle, you can turn off the remote start using the same method
to turn it on (Default = press “START” twice in 5 seconds)�
NOTE: If remote start activation is programmed for 1 press, the 1st press activates Run
Time Extender so an additional press is required to turn off remote start.
• Upon entering the vehicle during remote start mode, turn the ignition key to the “ON/RUN” posi-
tion (NOT START!!)� When you press the brake pedal, the remote start will turn off allowing the
ignition key to take over�
x2
PANIC: Press and hold the “LOCK” or “UNLOCK” button for 3
seconds�
• THE SIREN / HORN WILL SOUND, THE PARKING
LIGHTS WILL FLASH, AND THE DOORS WILL
LOCK OR UNLOCK DEPENDING WHICH BUTTON
IS PRESSED�
OR
4

Transmitter Functions (cont’d)
SILENT LOCK / UNLOCK: Press and release the “TRUNK” button
twice in 5 seconds�
• THE PARKING LIGHTS WILL FLASH, AND THE
SYSTEM WILL LOCK/ARM OR UNLOCK/DISARM
DEPENDING ON THE CURRENT SYSTEM STATE�
x2
REMOTE VALET: Press “LOCK” then “UNLOCK” then “TRUNK” +
“START” within 5 seconds�
• THE SYSTEM WILL ENTER VALET MODE�
SEE PAGE 8 FOR MORE INFO ON VALET MODE�
1
2
3
SENSOR BYPASS: Press and release the “TRUNK” button within 5
seconds of locking/arming the alarm system�
• THE SYSTEM WILL GIVE ONE CHIRP TO INDICATE
THE SENSOR IS BYPASSED�
NOTE: ALARM FUNCTIONS MUST BE ENABLED
AND AN OPTIONAL SENSOR ADDED TO USE THIS
FEATURE
LOW VOLTAGE/TEMP AUTO START: Press and release the
“START” button within 5 seconds of locking/arming the system�
• THE SYSTEM WILL GIVE ONE CHIRP TO INDICATE
THE LOW VOLT/LOW TEMP (15 DEGREES ONLY)
AUTO START IS ACTIVATED�
NOTE: LOW TEMP AUTO START IS ONLY AVAILABLE
ON EDP+ MODELS. SEE PAGE 6 FOR MORE INFO.
1
2
2
1
5

Transmitter Functions (cont’d)
AUXILIARY FUNCTIONS 1-4:
The actual operation of these functions will vary from car to car� They are designed to operate
extra functions like automatic sliding doors or motorized hatches� Aux 1-4 are virtual outputs only
available when this system is integrated with the vehicle’s data network� Consult with your installer
to nd out if any of these functions are available, then conrm each operation and write them
below�
- Auxiliary 1 Function (___________________): To activate this function, press and release the
“trunk” and “start” buttons simultaneously)�
- Auxiliary 2 Function (___________________): To activate this function, press and release the
“lock” and “trunk” buttons simultaneously)�
- Auxiliary 3 Function (___________________): To activate this function, press and release the
“unlock” and “start” buttons simultaneously)�
- Auxiliary 4 Function (___________________): To activate this function, press and release the
“unlock” and “trunk” buttons simultaneously)�
LOW BATTERY/LOW TEMP AUTOMATIC STARTING
Other Remote Start Features
TURBO TIMER FEATURE
PIT-STOP FEATURE
This feature allows you to leave your engine running for making quick errands. To use this fea-
ture, have the engine running normally from the ignition switch and your foot off the brake pedal�
Press the Valet Switch twice; the parking lights will ash and the horn chirps 5 times. Turn the key
off and the engine will remain running for the programmed run time�
This is recommended for vehicles equipped with a turbocharger. It allows the engine to idle
after driving to cool the turbo� When this Installer Programmable Feature (#10) is enabled, the
system will automatically keep the engine running as follows:
• With the engine running, hold the brake pedal and engage the parking brake.
When the brake pedal is released, the system will keep the engine running for the programmed
time (1, 2, or 3 minutes), and then automatically turn it off�
• The system may be locked while the engine is running. Turbo Timer can be prevented from
engaging, or “bypassed” if desired, by turning the engine off before engaging the parking brake�
NOTE: Temperature Related Features Are Only Available On EDP+ models.
This feature will automatically start the engine if the vehicle battery drops below 11 volts or the
interior temperature drops to 15 (or 32) degrees Fahrenheit� You must activate these features
each time you park your car to use them� They can be activated one of two ways:
Method 1 - Valet Switch
• Turn the ignition switch “on”, then “off” (engine not running), and within 7 seconds press the
valet switch twice� If there is a 2 second delay without additional valet button presses, the horn
will honk 3 times activating low voltage start mode�
• To activate low temp starting, enter low voltage start mode as described above but, immediate-
ly after the horn honks, press the valet switch 1 time (15 degrees) or 2 times (32 degrees) within 5
seconds. The horn will honk to conrm your selection.
Method 2 - With The Controller (Low Volt + Low Temp - 15 Degrees Only)
• Within 5 seconds of pressing LOCK, press the START button. You will get one chirp to conrm.
NOTE: When low temp start mode is activated, low voltage start is also activated� These features
will operate once every two hours until the ignition key is turned “ON”�
6

MANUAL TRANSMISSION STARTING
Remote starting with a manual transmission requires a different installation method and
installer feature #11 must be turned on� Also, a setup procedure that ensures the transmission
was left in neutral must be performed each time you leave your vehicle and intend to use remote
start later� Perform these steps:
1) With the engine running, hold the brake pedal, apply the parking brake, release the brake
pedal�
2) Use the transmitter as if you were activating remote start (default: press START twice)� The
status light will start to ash slow.
3) Turn off the ignition key and exit the vehicle�
4) Press LOCK on the transmitter� The engine will shut down (unless turbo timer is on) and the
status light will ash every 2 seconds to indicate it is ready to be remote started.
NOTE: Manual transmission starting is canceled if you enter the vehicle after performing
the setup procedure.
Other Remote Start Features (cont’d)
Security System Features (OPTIONAL)
LAST DOOR ARMING
This system can be congured to arm automatically when all the vehicle’s doors are closed
(see user feature #9)� When enabled, the siren/horn will chirp once when all of the doors are
closed. It will start a 30 second countdown (indicated by a fast ashing status light) after which,
the system will lock and/or arm� The 30 second arming delay will pause while a point of entry is
open. Turning ON the ignition key will cancel the arming sequence until the key is turned off and
the doors are all closed once again�
NOTE: Installer feature #13 must be on and the system must be wired for security functions.
AUTOMATIC REARMING
This automatically rearms the alarm if the system is disarmed from the remote� (see user
feature #10)� When disarmed by remote, the system will start a 90 second countdown (fast
ashing status light) to arm the system. This is useful if the controller accidentally disarms the
system when it’s kept in a purse or pocket where other items could potentially press the buttons�
ENHANCED AUTO REARM allows you to cancel the countdown by pressing UNLOCK a second
time within 5 seconds of the rst press to disarm the alarm.
NOTE: Installer feature #13 must be on and the system must be wired for security functions
PRE-WARN DETECTION
EXTERNAL SENSORS ARE OPTIONAL UPGRADES. TALK TO YOUR DEALER.
The optional impact sensor is designed, in addition to detecting a full impact, to warn
away potential violators when it detects a light impact to the vehicle� The system will
respond by chirping the siren/horn 3 times and locking the doors� This is very useful
when an intruder attempts to unlock the door with “slim jim” types of devices�
This system is equipped with our exclusive VIRTUAL ALARM technology. The se-
curity functions described in this section are available as a simple upgrade from your
dealer. It may require a plug-in module and some additional conguration, but will
greatly enhance your system’s capabilities and add theft deterrence to your vehicle.
TALK TO YOUR DEALER TODAY ABOUT UPGRADING!
7

WHEN THE SYSTEM TRIGGERS
If the system were to be compromised while armed, it will trigger sounding the
siren/horn and ashing the parking lights for 30 seconds (programmable). When
disarming the system after a trigger event, the siren/horn will chirp 4 times and the
parking lights will ash 4 times instead of the standard 2 times.
LOCK ON TRIGGER: If a door is opened when the system is triggered, it will wait
until the door is closed again, then lock the doors� This patented feature is useful to
further deny a thief of further access to the vehicle�
STORM SAFE MODE: When the system is triggered, pressing the “UNLOCK” button
will stop the alarm from sounding but will leave the doors locked� This function is use-
ful if you have a false triggering situation due to violent weather�
ZONE VIOLATION RECALL: The system is capable of telling you which zones were
triggered last. The system’s status light will ash to indicate which zone was triggered.
This occurs during the alarm cycle AND after disarming� The system will store the last
triggered zone until the vehicle’s ignition key is turned on� See “The Status Light” sec-
tion oon page 9 for further explanation of this feature�
NUISANCE PREVENTION: If the system prewarns 5 times within 15 minutes, it will
bypass the zone for the remainder of the 15 minutes before rearming the pre-warn
zone� Additionally, if a full trigger zone is left open, the system will trigger a total of 3
times before bypassing the zone� Once the zone is closed again, it will re-arm that
zone�
Security System Features (cont’d)
EMERGENCY OVERRIDE
If you lose or break your controller, you’ll need to perform an emergency override to
disarm the system and use your vehicle� To do so, use the following steps:
STEP 1 - Enter the vehicle (the alarm should sound)�
STEP 2 - Turn the ignition key to the “ON” position�
STEP 3 - Press the valet switch (located on the window-mount antenna) once �
STEP 4 - Turn the ignition “OFF”�
VALET MODE
Valet mode completely disables all security & remote start functions� Keyless entry
is still operable� To enter valet mode, perform the following steps:
STEP 1 - Disarm the system by remote or by performing an emergency override�
STEP 2 - Press and hold the valet switch for 2 seconds� The system will chirp once
and the status light will turn on�
EXITING VALET MODE - Press and release the valet switch once� The status light
will turn off�
Using The Valet Switch
8

The Status Light
The status lights, located in the window-mount antenna, provide a visual indication
of the system’s status�
SECURITY SYSTEM STATUS
OFF: The alarm is disarmed and not performing any automatic functions�
ON: The alarm is in valet mode�
FLASHING SLOW: The alarm is armed and monitoring all entry points�
FLASHING FAST: One of the automatic arming features is in progress�
AUTOMATIC TRANSMITTER VERIFICATION
Every time you turn on the ignition key, the status light will ash a number of times
equal to the number of transmitters programmed to the system. This unique security
feature combats potential thieves (valet attendant, mechanic, etc�) from adding their
own transmitter without your knowledge and accessing your vehicle at a later time�
ALARM ZONE VIOLATION RECALL
If the security system is triggered, upon disarming, the status lights will ash
a number of times to indicate exactly which zones, have been violated� It will
store the last 2 violated circuits and continually repeat the ash pattern until the
vehicle’s ignition key is turned ON�
2 FLASHES: Hood trigger
3 FLASHES: Door trigger
4 FLASHES: Sensor port trigger
REMOTE START STATUS
FLASHING SLOW: The engine was remote started successfully and is running�
FLASHING FAST: The remote start sequence has begun and is in process of starting
the vehicle’s engine�
2 FLASHES, PAUSE: The engine is running while the alarm is armed�
REMOTE START DIAGNOSTICS
The remote start system can also indicate which zone caused the last remote start
cycle to end� To see this indicator, place the system into valet mode� Immediately after
the chirp, the status light will ash to indicate which zone violation occured.
1 FLASH: Run time expired�
2 FLASHES: Brake pedal was pressed�
3 FLASHES: Engine stalled or a bad tach signal�
4 FLASHES: Received transmitter command to stop�
5 FLASHES: The neutral safety circuit was triggered�
6 FLASHES: The alarm was triggered or low battery voltage�
9

Anti-Carjacking Protection
The system is equipped with two separate Anti-Carjacking protection features
(ignition, open door, or both) that are selectable via user feature #12� Once activated,
the user has 53 seconds to cancel the Anti-Carjacking protection process (described
below)� If Anti-Carjacking is not cancelled, 53 seconds after being activated the siren
will begin to chirp for 7 seconds to alert the user that the system is about to enter into
an alarm condition� The Valet Switch may still be pressed once during this period to
cancel the Anti-Carjacking process�
If the Anti-Carjacking process is not cancelled before the 60 second countdown
expires, the system will enter an alarm condition, sounding the siren and ashing the
parking lights� 30 seconds after this occurs, or should the ignition be turned off in the
meantime, the stater interrupt will engage� Once the system enters the alarm condi-
tion, it will not respond to the transmitter, nor will the system reset automatically after
60 seconds, and it can only be disengaged by:
Step 1 Turning the vehicle’s ignition off�
Step 2 Turning the ignition back on�
Step 3 Within 5 seconds, perform an Emergency Override using the Valet Switch�
TYPES OF ANTI-CARJACKING PROTECTION
Ignition Activated Anti-Carjacking activates every time the vehicle’s ignition is
turned on� The Valet Switch must be pressed within 60 seconds of activating to
cancel Anti-Carjacking�
Door Anti-Carjacking (optional) activates when a door is opened after the vehicle
is started and the engine is running� The Valet Switch must be pressed within 60
seconds after activation to cancel Anti-Carjacking�
10

If the Unauthorized Transmitter Alert feature is on, programming a transmitter to the
system will activate the “UTA” warning and the extended Status Light indication� For
the next 48 hours, the siren/horn will sound a brief series of chirps every time the
vehicle’s ignition key is turned on�
Special Programming procedure to turn on the UTA feature: Use this method to
program transmitters or optional controllers, and to turn on the Unauthorized Trans-
mitter Alert feature�
Follow the same steps as the Standard Programming, but on any transmitter/con-
troller being programmed instead of pressing the “lock” button, press the “lock” and
the “unlock” buttons together� This action turns on the Unauthorized Transmitter
Alert feature and at the same time programs the transmitter or controller to operate
the system�
Once the Unauthorized Transmitter Alert feature is turned on, the warning will
sound for 48 hours after any transmitter programming� This feature can only be
turned off again by sending the system back to Omega for a reset�
Standard Programming: This method to program additional or replacement trans-
mitters does not affect the Unauthorized Transmitter Alert (UTA) feature� Before you
begin, have all transmitters which are to operate the system at hand�
Step 1 Then, turn the ignition “on” (do not crank the engine)�
Step 2 Within 5 seconds of Step 1, press the Valet Switch 5 times� The siren/horn will
briey sound, conrming that the system is ready to learn a transmitter code.
Step 3 Press the “lock” button on each transmitter, one at a time� The system will
chirp the siren/horn once to conrm that each was learned. If a code is not received
within 10 seconds of Step 2, the learning process will automatically exit�
Step 4 Then, turn the ignition “off” or wait 10 seconds to exit programming mode�
Programming Transmitters
Programming Features
TO MANUALLY CHANGE FEATURES:
Step 1 Turn the ignition key “ON”, then “OFF” (do not crank the engine)�
Step 2 Within 5 seconds of step 1, press the valet switch 5 times to access user
features (Press 10 times to access installer features)�
~ The siren/horn will sound and the status light will turn on�
Step 3 Within 10 seconds of step 2, press the valet switch the number of times cor-
responding with the desired feature’s number�
~ The siren/horn will chirp equal to the selected feature.
Step 4 Change the feature by pressing the remote button that matches the desired
setting�
~ The siren/horn will chirp equal to the selected setting.
Step 5 If you wish to change more features, repeat steps 3 & 4 at this time�
Step 6 To exit programming, turn the ignition key “ON” then “OFF”� Or, it will exit
automatically after 10 seconds of no activity�
A matrix of all programmable features and their options are on the last page of this
guide� For detailed information on each feature, please refer to the next section� Use
the procedure below to make any necessary changes�
11

User Programmable Features
Feature #6 - Open Door Bypass of Ignition Locking
On (press “lock” button to program) - DEFAULT
Off (press “unlock” button to program)
This feature cancels the automatic locking or unlocking of the vehicle’s doors if one of
the doors is open when the ignition switch is turned on or off�
Feature #5 - Ignition Controlled Lock/Unlock
Off (press “lock” button to program) - DEFAULT
Lock w/ Ignition On (press “unlock” button to program)
Unlock w/ Ignition Off (press “trunk” button to program)
Lock And Unlock w/ Ignition (press “start” button to program)
This feature controls the lock/unlock operations when the ignition key is turned on/off�
Feature #1 - Remote Start Run Time
10 Minutes (press “lock” button to program) - DEFAULT
5 Minutes (press “unlock” button to program)
15 Minutes (press “trunk” button to program)
20 Minutes (press “start” to program)
This sets the maximum amount of time that the remote start will keep the engine
running if it is not shut down by other methods�
Feature #2 - Flashing Light Conrmations
Unlock: ON, RS: ON (press “lock” button to program)
Unlock: ON, RS: Flash (press “unlock” button to program)
Unlock: Flash, RS: ON (press “trunk” button to program)
Unlock: Flash, RS: Flash (press “start” button to program) - DEFAULT
This feature affects the parking light conrmations for system unlock & remote start
functions� With the above options, you can select any combination of:
Unlock: Flash - Flashes twice after unlock�
Unlock: ON - Flashes twice, then stays on for 30 seconds after unlock�
RS: ON - Stays on during remote start mode�
RS: Flash - Flashes once every 1�5 seconds during remote start mode�
Feature #3 - Conrmation Chirp Volume
Low (softest) (press “lock” button to program)
Medium Low (press “unlock” button to program)
Medium High (press “trunk” button to program) - DEFAULT
High (loudest) (press “start” button to program)
This feature allows the choice of different chirp volume levels, and when programming
it, each selection will be conrmed in the chosen volume making it easy to choose the
most suitable setting�
Feature #4 - BROWN Wire Audible Output
Pulsed Horn Low (press “lock” button to program) - DEFAULT
Pulsed Horn Medium (press “unlock” button to program)
Pulsed Horn High (press “trunk” button to program)
Steady Siren (press “start” button to program)
This changes the BROWN wire’s audible output when the alarm is triggered� Steady
siren must be selected when using a siren (other horn outputs stay at the Medium
setting)� The horn honk options will affect all horn honk outputs used as well as
change the BROWN wire’s function�
12

Feature #9 - Last Door Arming
Off (press “lock” button to program) - DEFAULT
On w/o doors locking (press “unlock” button to program)
On w/ doors locking (press “trunk” button to program)
“Last Door Arming” has the system automatically arm itself every time you exit the
vehicle (the complete operation is described on page 7)�
Feature #10 - Automatic Rearming
Off (press “lock” button to program) - DEFAULT
On w/o doors locking (press “unlock” button to program)
On w/ doors locking (press “trunk” button to program)
Enhanced auto rearm (press “start” button to program)
“Automatic Rearming”, described on page 7, rearms the alarm if accidentally dis-
armed� Options are to have Automatic Rearming operate with or without also locking
the doors when the system does rearm� Enhanced auto rearm allows you to cancel
the rearming sequence by pressing unlock a 2nd time after disarming.
User Programmable Features (cont’d)
Feature #7 - Unlock w/ Trunk Release
On (press “lock” button to program) - DEFAULT
Off (press “unlock” button to program)
“2nd channel” is most commonly used for trunk release, in which case the alarm
should also disarm. This feature, when on, congures the system to unlock/disarm
when the 2nd channel is activated�
Feature #8 - Remote Start Activation From The Remote
Press “start” button 1 time (press “lock” button to program)
Press “start” button 2 times (press “unlock” button to program) - DEFAULT
Press “start” button 3 times (press “trunk” button to program)
Press “start” button 4 times (press start” button to program)
This feature changes how the remote start feature is activated from the remote�
Feature #11 - Conrmation Chirps
Siren + Horn (press “lock” button to program)
Siren Only (press “unlock” button to program) - DEFAULT
On Demand (siren+horn) (press “trunk” button to program)
Off (press “start” button to program)
This feature selects whether the siren and/or horn give conrmation chirps� Both
outputs will always sound when the alarm system is triggered or in panic mode�
NOTE: Both the siren and horn outputs must be connected for this feature to function.
Feature #12 - Anti-Carjacking
Ignition Only (press “lock” button to program)
Door Only (press “unlock” button to program)
Ignition + Door (press “trunk” button to program)
Off (press “start” button to program) - DEFAULT
This selects between the 2 forms of anti-carjacking protection� Details on using anti-
carjacking protection are described on page 10�
13

Blank
Page
14

Installer Programmable Features
This group of Installer Programmable Features are all accessed as a group in the second level of
features’ programming� These features have a direct affect upon the system’s operations related
to the installation and vehicle type AND SHOULD ONLY BE CHANGED BY THE INSTALLER!!!
Feature #1 - Remote Start Activation From The WHITE/BLUE Wire
1 pulse (press “lock” button to program) - DEFAULT
2 pulses (press “unlock” button to program)
3 pulses (press “trunk” button to program)
4 pulses (press start” button to program)
This feature changes how the remote start feature is activated from the (-) activation input wire�
Feature #2 - PINK/WHITE (IGN #2) Wire Function
Ignition (press “lock” button to program) - DEFAULT
Accessory(press “unlock” button to program)
Starter (press “trunk” button to program)
This feature changes the operation of the unit’s large PINK/WHITE output wire� This feature
should only be programmed by the installer�
Feature #3 - Engine Detection Method
Tachless Hi (press “lock” button to program) - DEFAULT
Tachless Lo (press “unlock” button to program)
Tach Wire (press “trunk” button to program)
Data Tach (press “start” button to program)
Crank Only (press “lock” & “unlock” to program)
This feature selects the method in which the remote start monitors the engine’s running condition
in remote start mode�
“Tachless Hi” sensitivity mode uses a preset crank time (see installer feature #7) and monitors
the vehicle’s voltage level to determine if the engine is running� This setting looks for a voltage
increase of 0�3v after cranking�
“Tachless Lo” sensitivity mode operates like the “Tachless Hi” setting but looks for a voltage
increase of 0�5v after cranking�
“Tach Wire” Before this setting is programmed, refer to the “Violet/White wire” section of the
installation manual for proper wiring connection and the Tach Learn Procedure� It will crank the
engine for up to 3 seconds or until a tach signal is detected�
“Data Tach” mode operates just like the “Tach Wire” setting except it takes its reading from the
D2D data port instead of using the Violet/White wire� Before using, make sure this function is sup-
ported by the Databus Interface module�
“Crank Only” AKA “blind start” is similar to the “Tachless” settings, however, it only makes one
start attempt and does not monitor engine running conditions� This is useful for many “push-to-
start” vehicles�
Feature #4 - Gasoline Or Diesel Engine
Gasoline (press “lock” button to program) - DEFAULT
Diesel 15 Sec. Delay (press “unlock” button to program)
Diesel 20 Sec. Delay (press “trunk” button to program)
Diesel 30 Sec. Delay (press “start” button to program)
This feature changes the system’s timing of the ignition and starter output sequence for gas or
diesel engines� Gasoline: the starter output will occur 3 seconds after the ignitions turn on� When
in “Tachless” mode, the engine running status is determined 10 seconds after starting� Diesel:
the starter output will occur 15, 20, or 30 seconds after the ignitions turn on (allows for glow plug
warming)� When in “Tachless” mode, the engine running status will be determined 40 seconds
after cranking�
15

Installer Programmable Features (cont’d)
Feature #5 - Satellite Port, Green Wire Function
Dome Light Output (press “lock” button to program)
Start (press “unlock” button to program) - DEFAULT
Ignition Output (press “trunk” button to program)
Accessory Output (press “start” button to program)
Status / GWR (press “lock” & “unlock” button to program)
This determines the function of the Green wire on the satellite relay port� This output can be
programmed for different functions as needed�
Feature #7 - Starter Cranking Time
0.75 Second (press “lock” button to program) - DEFAULT
1.00 Second (press “unlock” button to program)
1.5 Seconds (press “trunk” button to program)
2.25 Seconds (press “start” button to program)
This feature determines the crank time of the 1st start attempt when in “Tachless” mode� If the
engine doesn’t start on the rst attempt, it will retry up to 3 more times extending the crank time by
an additional 0�2 second with each attempt�
Feature #10 - Turbo Timer
Off (press “lock” button to program) - DEFAULT
Run 1 Minute (press “unlock” button to program)
Run 2 Minutes (press “trunk” button to program)
Run 3 Minutes (press “start” button to program)
This feature, the operation of which is described on page 7, when turned on
congures the system to automatically keep the engine running briey after the key is turned off.
This operation is designed specically for vehicles with turbocharged engines.
NOTE: This feature is dependent on the proper wiring of the neutral safety circuit.
Feature #8 - Door Lock/Unlock Outputs
0.8 Second Outputs (press “lock” button to program) - DEFAULT
3 Second Outputs (press “unlock” button to program)
Double Pulse Unlock Output (press “trunk” button to program)
Total Closure Lock Output (press “start” button to program)
This changes the system’s doorlocking outputs to suit different vehicle requirements. The total
closure setting provides a 28 second lock pulse (press LOCK or UNLOCK during the pulse to stop
it) and a 0�8 second unlock pulse�
Feature #9 Remote Start Lock Control
Off (press “lock” button to program) - DEFAULT
Lock After Start (press “unlock” button to program)
Unlock before start (press “trunk” button to program)
Unlock Before RS & Lock After RS (press “start” button to program)
This feature allows for OEM alarm/lock control in relation to remote start operations thus eliminat-
ing extra wiring for OEM alarm control�
Feature #6 Satellite Port, Blue Wire Function
Ignition (press “lock” button to program)
Status / GWR (press “unlock” button to program) - DEFAULT
Defrost Pulse (EDP+ Models Only) (press “trunk” button to program)
Pulse After Engine Off (press “start” button to program)
Horn (press “lock” & “unlock” button to program)
This determines the function of the Blue wire on the Blue satellite relay port�
The Status setting turns on briey before the Ignition output and stays on during remote start
mode� The other pulse settings give a 0�8 second pulse under the selected condition� Defrost
Pulse will send a pulse after start only when the cabin temperature is below freezing� On non-
EDP+ models, this setting will always send a pulse after start�
16

Installer Programmable Features (cont’d)
Feature #11 - Manual Transmission Mode
On (press “lock” button to program)
Off (press “unlock” button to program) - DEFAULT
This feature changes the parameters of the system’s remote start operation to be suitable for
manual transmission-equipped vehicles via a “setup” procedure which must be followed upon exit-
ing the vehicle to ensure the transmission is in neutral�
Feature #12 Data Port Protocol
Green: DBI, Black: DBI (press “lock” button to program) - DEFAULT
Green: iData, Black: iData (press “unlock” button to program)
Green: DBI, Black: iData (press “trunk” button to program)
Green: iData, Black: DBI (press “start” button to program)
This feature determines which data protocol is used on each data port� Choose this based on the
accessory being connected to the port�
Feature #13 - Virtual Alarm
On (press “lock” button to program)
Off (press “unlock” button to program) - DEFAULT
This feature converts the system into a Security/Remote Start System by enabling antitheft alarm-
oriented operations and features� OPTIONAL MODULES MAY BE REQUIRED.
Feature #14 - Pulse Ignition On Disarm
On (press “lock” button to program)
Off (press “unlock” button to program) - DEFAULT
This feature will pulse the ignition and activate any attached immobilizer bypass module for
vehicles that require the ignition to be turned on to disarm the OEM alarm.
Feature #15 Lock On Prewarn
On (press “lock” button to program) - DEFAULT
Off (press “unlock” button to program)
This feature will automatically lock the doors to combat unauthorized entry from lock picking when
the prewarn zone is triggered� AN OPTIONAL SENSOR IS REQUIRED.
Feature #16 - Starter Interrupt Output Functions (EDP+ Models Only)
Alarm Only (press “lock” button to program)
Anti-Grind Only (press “unlock” button to program) - DEFAULT
Alarm & Anti-Grind (press “trunk” button to program)
Automatic (press “start” button to program)
Alarm Only - The Starter Interrupt is operable whenever the alarm is armed�
Anti-Grind Only - The Starter Interrupt is operable whenever remote start is on�
Alarm & Anti-Grind - This setting engages starter interrupt when the alarm is armed AND when
the system is in remote start mode� This prevents the starter from grinding if the user accidentally
turns the key to “START” during remote start�
Automatic - This will cause the Starter Interrupt output to automatically engage 90 seconds after
the ignition switch is turned “off”, and after disarming the system�
Feature #17 Low Temp Crank Extender (EDP+ Models Only)
0ms (Off) (press “lock” button to program)
200ms (press “unlock” button to program) - DEFAULT
300ms (press “trunk” button to program)
400ms (press “start” button to program)
When the vehicle’s interior temperature is below freezing, this feature adds extra crank time to the
base timing (see installer feature #7)� It applies to tachless modes only (installer feature #3)�
17

Blank
Page
18

CONVENIENCESECURITYINSTALLER ONLY
User Feature Programming: Ignition on, off, press valet 5 times
# Feature Lock Button
(Brake x 1)
Unlock button
(Brake x 2)
Trunk button
(Brake x 3)
Start button
(Brake x 4)
Lock + Unlock
(Brake x 5)
1 Remote Start Run Time 10 min 5 min 15 min 20 min
2 Flashing Light Conrmations Unlock: ON
RS: ON
Unlock: ON
RS: Flash
Unlock: Flash
RS: ON
Unlock: Flash
RS: Flash
3 Conrmation Chirp Volume Low Med-Low Med-High High
4 BROWN Wire: Siren / Pulsed Horn Pulse LOW Pulse MED Pulse HI Steady Siren
5 Ignition Lock / Unlock Off Ign On = Lock Ign. Off = Unlock Lock + Unlock
6 Door Open Bypass for Feat. #5 On Off
7 Unlock w/ Trunk Release On Off
8 RS Activation (Remote) Start x 1 Start x 2 Start x 3 Start x 4
9 Last Door Arming Off On w/o Lock* On w/ Lock*
10 Automatic Rearming Off On w/o Lock On w/ Lock Enhanced
11 Conrmation Chirps Siren + Horn Siren Only On Demand Off
12 Anti-Carjacking Ignition Door* Ignition + Door* Off
Installer Feature Programming: Ignition on, off, press valet 10 times
1 RS Activation (WHITE/BLUE wire) 1 Pulse 2 pulses 3 pulses 4 pulses
2 PINK/WHITE Wire Ignition Accessory Starter
3 Engine Detection Tachless Hi Tachless Lo Tach Wire Data-tach Crank Only
4 Gasoline or Diesel Engine Gasoline 15 sec Diesel 20 sec Diesel 30 sec Diesel
5 Sat Port GREEN Wire Dome Light Start Ignition Accessory Status
6 Sat Port BLUE Wire Ignition Status Pulse After Start
below freezing
Pulse After
Engine Off Horn
7 Crank Time 0.75 sec 1 sec 1.5 sec 2.25 sec
8 Door Lock/Unlock Outputs 0.8 sec 3 sec Double Unlock Total Closure
9 Remote Start Lock Control Off Lock after
Start
Unlock before
Start Lock + Unlock
10 Turbo Timer Off 1 min 2 min 3 min
11 Manual Transmission On Off
12 Data Port Protocol Green: DBI
Black: DBI
Green: iData
Black: iData
Green: DBI
Black: iData
Green: iData
Black: DBI
13 Virtual Alarm On Off
14 Pulse Ign. on Disarm On Off
15 Lock On Prewarn On Off
16 Starter Interrupt
(EDP+ models only) Alarm Only Anti-grind Only Alarm/Anti-Grind Automatic
17 Low Temp Crank Extender
(EDP+ models only) 0 ms 200 ms 300 ms 400 ms
Grey Background = VIRTUAL ALARM (installer feature #13) Must Be ON
* Door Status Is Required On Data Ports Via External Module.
Programmable Features Matrix
19

Back Cover
Color cover is in a
separate le.
20