Exigo E60 User manual

E60
FOLDING RACK
XL-1380
DIMENSIONS L x W x H
mm (inch)
WEIGHT
kg (lbs)
MAX LOAD
kg (lbs)
COMMERCIAL
WARRANTY
759 x 1290 x 2140
(30 x 51 x 84)
61
(134)
450
(992)
Main Frame
Lifetime

2
WARNING
SERIOUS INJURIES TO USERS, BYSTANDERS OR INSTALLERS CAN OCCUR IF THE INSTRUCTIONS AND
WARNINGS CONTAINED IN THIS MANUAL ARE NOT FOLLOWED. TO MINIMIZE THIS RISK, READ THE
MANUAL BEFORE BEGINNING THE INSTALLATION TO FAMILIARIZE YOURSELF WITH ITS CONTENTS
AND THEN BE CERTAIN TO FOLLOW EACH OF THE STEPS AND PRACTICES DESCRIBED.
TAPE MEASURE
TOOLS REQUIRED
SPIRIT LEVEL
VACUUM
6MM ALLEN KEY
PENCIL
HAMMER DRILL
19MM & 17MM
SPANNER / SOCKET
NO. PART QTY
1 UPRIGHT 2
2 WALL PLATE 2
3 PULL-UP BAR 1
4 WALL ARM 4
5 J-HOOKS (PAIR) 1
6 SELECTOR PIN 4
7 J-HOOK PLASTIC 2
PARTS
NO. FIXING QTY
1 M12 X 90 BOLT 8
2 M12 X 120 BOLT 4
3 M12 WASHER 32
4 M12 NYLOC 12
5 M10 X 35 BUTTON HEAD 10
6M10 SHAKE PROOF WASHER 10
7 M10 X 65 COACH SCREW 8
8M12 X 50 WALL PLUG 8
9M10 X 25 WASHER 8
10 60 X 60 END CAP 2
FIXINGS

3
STEP 1
USING THE DIMENSIONS BELOW, MEASURE OUT, DRILL AND FIX THE UPPER STRINGER PLATE TO THE
WALL USING THE SUPPLIED FIXINGS. USING A SPIRIT LEVEL TO ENSURE THAT IT IS FIXED TO THE
WALL LEVEL.
SOLID WALLS: DRILL A 12MM HOLE AND USE A WALL PLUG FIXING.ENSURE THE HOLE IS VACCUUMED OUT BEFORE
INSERTING THE WALL PLUG.
STUDDED WALL: USE M10X65 COACH SCREW, MAKING SURE THAT YOU FASTEN INTO STUDDED WALL UPRIGHTS.
450mm
17.7Inch
450mm
17.7Inch
1220mm
48Inch
1913mm
75.3Inch
403mm
15.8Inch
DATE
Drawing of
0
A3
SHEET 1 OF 1
SCALE: 1:12
DWG No:
Machine:
-
DEBUR AND BREAK SHARP EDGES
ALL Dimensions in mm
Confirmed By:
M.M
This Drawing is Property Of
A & D Sports Limited and Must Not
Be Copied or Duplicated Unless
Authorised by A & D Sports Limited.
All Rights Reserved.
XXXXX
1 1
Bill of Materials:
Material:
Finish:
Wall Fixing Points
XL-1380 Lite Folding Rack
Mild Steel
Powder Coat Unless
Stated Otherwise
A & D Sports Limited
Golden Works
Lawton Street
Rochdale
OL12 0LQ
United Kingdom
Tel: [phone]
Email: [email protected]
3rd Angle Projection
Drawn By:
-
Do Not Scale Drawing
Tolerances (Unless Otherwise Stated)
Linear +- 0.5
Angular +- 0.5'
Hole +- 0.1
0.1
0.1
0.1
1.0
09/02/2021

4
STEP 2
ATTACH THE REAR ARMS TO THE UPRIGHTS, USING THE FIXINGS OUTLINED BELOW. REPEAT THIS
STEP FOR BOTH SIDES.
NO. FIXING QTY
1 M12 NYLOC 4
2 M12 WASHER 8
3 M12 X 90 BOLT 4
1
2
3

5
STEP 3
LOOSELY ATTACH THE UPRIGHTS TO THE TOP STRINGER, THEN ATTACH THE BOTTOM STRINGER TO
THE BOTTOM ARMS AND MARK OFF THE FIXING POINTS ON THE WALL.
REMOVE UPRIGHTS AND DRILL THE FIXING HOLES AS MARKED.
ATTACH THE BOTTOM STRINGER TO THE WALL USING THE FIXINGS SUPPLIED AND FOLLOWING THE
SAME PROCEDURE AS STEP 1.

6
STEP 4
ATTACH THE UPRIGHTS TO THE WALL STRINGER PLATES USING THE FIXINGS IN THE BELOW TABLE
AND DIAGRAM.
NO. FIXING QTY
1 M12 NYLOC 4
2 M12 WASHER 16
3 M12 X 120 BOLT 4
3
2
2
2
2
1

7
STEP 5
WHEN USING THE RACK, FOLD OUT BOTH ARMS AND SECURE WITH THE DROP PIN. THE PULLUP BAR
THEN SLOTS FIRMLY INTO THE TOP OF THE UPRIGHTS AND WILL BE LOCKED IN PLACE.

8
STEP 6
ASSEMBLE THE J-HOOKS USING THE FIXINGS BELOW.
NO. FIXING QTY
1 M10 INTERNAL WASHER 10
2 M10 X 35 BUTTON HEAD 10
1
2
1

9
MAINTENANCE & EQUIPMENT USAGE
PREVENTATIVE MAINTENANCE IS CRITICAL TO THE SAFETY OF USERS AS WELL AS ENSURING THE
OPTIMUM FUNCTION OF THE EQUIPMENT. ONLY USE COMPONENTS FROM THE SUPPLIER WHEN SERVICING
YOUR EQUIPMENT. BE CERTAIN TO REPLACE ANY COMPONENTS AT THE FIRST SIGNS OF WEAR.
DAILY INSPECTION
PAINT: LOOK FOR PAINT CHIPS AND FILL IN IMMEDIATELY
WITH TOUCH-UP PAINT FROM THE SUPPLIER.
FIXINGS: CHECK ALL NUTS, BOLTS AND ASSOCIATED
FRAME PARTS FOR ANY LOOSENESS. TIGHTEN AS
REQUIRED.
WALL FIXINGS: ENSURE WALL FIXINGS ARE SOLID AND
SECURED TO THE WALL WITH NO DAMAGE. DO NOT USE IF
ANY DAMAGE IS APPARENT OR FIXINGS ARE LOOSE.
MAIN FRAME: INSPECT FOR ANY DAMAGE. NOTIFY THE
SUPPLIER OF ANY FAULTS OR DAMAGE IMMEDIATELY.
DAILY CLEANING
MAIN FRAME: CLEAN THE MAIN FRAME WITH A MILD
SOAP SOLUTION OR AN APPROVED CLEANER AND DRY
COMPLETELY.
PLASTIC PARTS: WIPE PLASTIC PARTS WITH A MILD SOAP
SOLUTION OR AN APPROVED CLEANER TO REMOVE DIRT
AND GREASE MARKS AND DRY COMPLETELY.
CHROME PARTS: WIPE CHROME PLATED PARTS WITH A
MILD SOAP SOLUTION OR AN APPROVED CLEANER AND
DRY COMPLETELY.
HEAVY DUTY CLEANING: IF YOU HAVE SCUFF MARKS,
GREASE OR A HEAVY DIRT BUILDUP ON FRAME
COMPONENTS, START WITH A MILD SOAP SOLUTION OR
A DILUTED SOLUTION OF AN ALL PURPOSE CLEANER.
IF YOU CANNOT REMOVE THE MARKS USING THOSE
METHODS, USE A CAR POLISH/CLEANER. DO NOT USE
SOLVENTS SUCH AS LACQUER THINNER, MINERAL
SPIRITS OR ACETONE. FOR DEEPER SCUFF MARKS, USE
AN AUTOMOBILE FINISH RUBBING COMPOUND.
CAUTION: CERTAIN ANTI-BACTERIAL CLEANERS
AND OTHER HARSH CLEANING AGENTS CAN INDUCE
CORROSION ON THE EQUIPMENT. IT IS IMPORTANT NOT TO
LEAVE PARTS DAMP. THIS WILL INCREASE THE POTENTIAL
FOR CORROSION TO OCCUR.
EQUIPMENT USAGE
REVIEW AND UNDERSTAND ALL OF THE WARNING
LABELS AFFIXED TO THE EQUIPMENT.
BE CERTAIN THAT THE EQUIPMENT OPERATION IS
UNDERSTOOD BEFORE IT IS USED. USE THE RACK ONLY
FOR THE INTENDED EXERCISE.
KEEP CHILDREN AWAY FROM THIS EQUIPMENT.
TEENAGERS MUST BE SUPERVISED.
IT IS RECOMMENDED THAT USERS RECEIVE A THOROUGH
MEDICAL EXAM BEFORE COMMENCING AN EXERCISE
PROGRAM. ALL MEDICAL ISSUES SHOULD BE REVIEWED
TO ENSURE THAT WEIGHT TRAINING WILL NOT
AGGRAVATE PRE-EXISTING MEDICAL CONDITIONS.
DO NOT USE THE EQUIPMENT IF IT APPEARS DAMAGED,
JAMMED OR INOPERABLE.
DO NOT MODIFY THE EQUIPMENT IN ANYWAY.
DO NOT WEAR LOOSE OR DANGLING CLOTHES/OBJECTS
WHEN USING THIS EQUIPMENT.