BH FITNESS G6485 User manual

1
G6485
UNIDAD ELECTRÓNICA
ELECTRONIC MONITOR
UNITÉ ÉLECTRONIQUE
ELEKTRONIKEINHEIT
UNIDADE ELECTRÓNICA
IMPIANTO ELETTRONICO
ELEKTRONISCHER MONITOR

2
Fig.1 Fig.2
Fig.3

8
English
ELEMENTS OF THE MONITOR.-
A: This display gives a simultaneous
readout of Time; Programs; Speed;
Distance; Incline; Pulse rate and
Calories.
B: Incline function quick access keys
or buttons (6- 8- 10).
C: The electronic monitor has 9 push
buttons or keys; FAN; PROGRAM;
MODE; INCLINE (↨); START/STOP;
SPEED Km/h (↨).
E: Slot for safety key.
F: Speed function quick access keys or
buttons (6- 9- 12 Km/h).
g: Safety key.
H: ECO key
START/STOPING.-
Plug the unit into a wall socket with an
EARTH terminal and set switch (L) to
position (1), Fig.1.
The safety key (g) must be inserted
into its spot (E) Fig.2, otherwise the
machine will not operate. As soon as
the safety key (g) is in place, the
machine will beep and all of the
displays will show a [00:00] value,
indicating that the machine is READY
to be used.
CHANGING FROM
KILOMETRES TO MILES.-
This machine has the option to display
speed in km/h or mph.
The factory setting for the machine is
km/h.

9
To change from km/h to mph follow
these steps:
Unplug the machine from the mains
supply, remove the safety key. Plug
the machine back in.
Press and hold the PROGRAM and
MODE keys at the same time for 5
approximately seconds. The speed
display (A) “0.6” corresponds to miles
per hour. and insert the safety key (g)
into its slot.
OPERATING INSTRUCTIONS.-
MANUAL MODE
This monitor has program (MANUAL).
For programs MANUAL you can specify
the duration of the exercise between (5
to 99) minutes, distance between (1 to
99.5) and calories between (20 to 990).
Pressing the START/STOP key will light
the MANUAL and the machine will start
within 3 seconds, shown by a
countdown on the TIME display, at a
speed of 1.0km/h.
You can increase or decrease the
speed setting in MANUAL mode by
pressing the SPEED (↨) keys, between
1.0–16 km/h.
The machine will stop if you press the
START/STOP key or if you remove the
SAFETY KEY
PROGRAM MODE.-
This monitor has 17 programs
(MANUAL, P01; P02; P03; P04; P05;
P06; P07; P08; P09; P10; P11; P12;
U01; U02; U03; BODY-FAT).
For programs P1 to P12 you can
specify the duration of the exercise
between (5 to 99) minutes.
Program graphics for P1 to P12.
See end pages.-
With the machine ready, press the
PROGRAM key and P01 will appear
on the display, by pressing the
PROGRAM key you can access the
programs (P1 al P12: BODY-FAT),
once you have chosen a program
press the MODE key and the word
TIME will begin to flash.
Use the SPEED (↨) keys to specify the
duration of the program (5 – 99
minutes). The monitor has a default
program setting of 30 minutes.
Press the START/STOP key and the
machine will start to operate after 3
seconds, shown by the countdown on
the central display, based on the
values it has been given.
You can change the speed settings at
any time during the exercise by
pressing the SPEED (↨) keys, and the
inclination settings by pressing the
INCLINE (↨) keys.
ECO FUNCTION.-
Press this button when in manual or
program mode to enter into economic
mode. The machine will change the
incline and configuration to reduce
power consumption and the time
window will alternate time with the
word ECO. Press the ECO button
again to exit this function.
USER PROGRAM MODE.-
The user programs allow you to design
the speed and inclination graphs with
reference to your fitness level.
With the machine ready, press the
PROGRAM key and U01 will appear
on the display, by pressing the
PROGRAM key you can access the
user program, once you have chosen
a program press the MODE key and
the first step of the program you are
designing will be shown in the
TIME/DISTANCE window, (001).
Use the INCLINE

keys to selec

10
t the inclination level you want for the
first stage (between 0 to 12), press the
SPEED

keys to select the speed that
you want for the first stage between 1
and 16 km/h).
Press the MODE key and this will take
you to the second stage (002) carry
out the same procedure as in (001)
varying the speed and inclination
settings for this stage, and so on up to
stage 16 to complete the User
Program Graph.
By pressing the MODE key you can
program a time limit for the exercise
(between 5 to 99 minutes).
If the programmed exercise time is 16
minutes then each stage will last 1
minute.
Press START and the machine will
start after a 3 second countdown,
shown on the TIME display.
BODY FAT PROGRAM.-
The (“F” BODY-FAT) program is
designed to calculate the user’s body
fat percentage.
Press the (“F” BODY-FAT) program
key, then press the MODE key and by
using the (↨) keys to select SEX
(Male01– Female 02), press the MODE
key to confirm, use the (↨) keys select
your AGE (10 – 99) press the MODE
key to confirm, use the (↨) keys to select
your WEIGHT (20 – 150Kg).
Press the MODE key to confirm, use the
(↨) keys to select HEIGHT (100 -
200cm), press the MODE key to
confirm.
Place your hands on the handgrip
sensors (R), as shown in Fig.3, and
after a few seconds the screen will
display the result.
FAT. (Body fat).–
The body fat function helps you to
calculate your body fat percentage.
REF. TABLE:
BODY FAT PERCENTAGE %
SEX /
FAT%
LOW
LOW /
AVE
RAGE
AVE
RAGE
HIGH
MALE
< 13%
13%-
25,8% 26%- 30% >30%
FEMALE
<23% 23%-
35,8% 36%- 40% >40%
BODY TYPE
There are 9 body types based on the
percentage of fat calculated.
TYPE 1 (5%-9%) Extremely athletic
TYPE 2 (10%-14%) Ideal sportsman
TYPE 3 (15%-19%) Very slender
TYPE 4 (20%-24%) Sportsman
TYPE 5 (25%-29%) Ideal health
TYPE 6 (30%-34%) Slender
TYPE 7 (35%-39%) Very overweight
TYPE 8 (40%-44%) Overweight
TYPE 9 (45%-50%) Extremely obese
The main screen will display the type
of profile for your body type.
If the error code “E-3” appears then
this means that an error has occurred,
position your hands correctly on the
pulse sensors (R), Fig.3.
EMERGENCY STOP.-
For the user’s maximum safety, this unit
is equipped with a safety key (g) and a
STOP button. The safety key (g) must
be slotted into its housing (E), Fig.2,
otherwise the machine will not start.
When you are using the machine
always clip the cord on the safety key to
your clothing. Tugging on the cord will
pull the safety key out of its slot and the
machine will stop immediately. To
restart the machine simply put the key
back into the key slot.

11
Remove the safety key (g) whenever
the machine is not being used and keep
it out of children’s reach. Pressing the
red button marked STOP will also stop
the unit immediately. To restart it, press
the button marked START/STOP again.
ELEVATION.-
The inclination function operates
independently of all other functions.
Each time that you set switch (L) to
position I, as described in the Starting
section, Fig.1. the inclination level that
was last used will be displayed.
If inclination is not at zero when the
START/STOP key is used to begin
exercising, the machine will zero itself
while it is starting.
You can adjust the elevation level by
pressing the INCLINE(+) or INCLINE
(-) keys to specify a value of 0 to 15,
depending on how you would like to
do the exercise.
Important: Do not change the
inclination level of your treadmill by
propping it up on objects.
IMPORTANT: THE INCLINATION
LEVEL MUST BE AT ITS LOWEST
SETTING BEFORE ATTEMPTING
TO PUT THE TREADMILL INTO THE
FOLDED POSITION.
PULSE MEASUREMENT.-
Your pulse rate is measured by
placing both hands on pulse sensors
(R) with which the electronic unitis
equipped. The pulse rate readout will
appear after a few seconds. The heart
symbol beside the pulse rate value will
flash in time with your heart rate,
Fig.3.
IMPORTANT: This is not a medical
appliance and therefore the heart rate
shown is merely for guideline
purposes.
THE MANUFACTURER RESERVES
THE RIGHT TO MODIFY THE
SPECIFICATIONS OF ITS
PRODUCTS WITHOUT PRIOR
NOTICE.

12
FAULT FINDING CHART
PROBLEM CHECKS SOLUTIONS
1.The monitor does not
switch on.
1) Make sure that the
machine is plugged in, the
ON/OFF switch in position 1
and that the safety key is
inserted.
1) Plug the machine into the
mains supply. Set the switch to
position 1 and insert the safety
key.
2.The monitor switches
on but the motor fails
to start.
2) Check that the current
limiter is pressed in.
2) Switch the machine off and
press the circuit breaker in.
Lubricate the treadmill band.
3.Walking motion is
jerky on the
treadmill.
3.a) Check that the belt is
lubricated.
3.b) Check the tension on the
sliding belt.
3.c) Check the tension on the
drive belt.
3.a) Lubricate the sliding belt.
3.b) Adjust the belt tension.
3.c) Adjust the drive belt tension.
4.The machine stops
(the breaker trips). 4) Check that the band is lubricated. 4) Reset the overload button with the On /Off switch at „0“ and
lubricate the treadmill band.
5.Electrical shocks
through the handrail.
5) Check that the machine is
plugged into an earthed
mains socket.
5) Plug the machine into an
earthed mains socket.
6.The treadmill belt
skews off centre.
6.a) Check that the machine
is level on the floor.
6.b) Check that the machine
does not wobble.
ERROR CODES
Monitor screen display
E1 Possible message fault. Connect the wire well between top controller and bottom controller
Monitor screen display
E2 Burst clash. Operating with correct voltage;Connect the motor wire again.
Monitor screen display
E3 No speed sensor signal Replace the sensor light on the bottom controller or speed sensor.
Monitor screen display
E5 Possible motor overload. Lubricate the belt.
Monitor screen display
E7 Safety key. Insert the safety key.
Do not hesitate to get touch with the Technical Assistance Service if you have any
queries by phoning customer services (see last page in manual).

40
(E) PERFILES DE LOS PROGRAMAS;
(GB) PROGRAM PROFILES;
(F) PROFILS DES PROGRAMMES;
(D) PROGRAMMPROFILE;
(P) PERFIS DOS PROGRAMAS;
(I) PROFILI DEI PROGRAMMI;
(NL) PROGRAMMAPROFIELEN;

41

BH FITNESS SPAIN
EXERCYCLE,S.L.
(Manufacturer)
P.O.BOX 195
01080 VITORIA (SPAIN)
Tel.: [phone]
Fax: [phone]
e-mail: [e-mail]
www.bhfitness.com
POST-VENTA
Tel: [phone] /
902 170 258
Fax: [phone]
e-mail: [e-mail]
BH FITNESS NORTH AMERICA
20155 Ellipse
Foothill Ranch
CA 92610
Tel: + 1 949 206 0330
Toll free: [phone]
Fax: [phone]
e-mail:
[e-mail]
www.bhnorthamerica.com
BH FITNESS ASIA
BH Asia Ltd.
No.80, Jhongshan Rd.,
Daya Dist.,
Taichung City 42841,
Taiwan. R.O.C.
Tel.: [phone]
Fax: [phone]
E-mail: [email protected]m.tw
BH FITNESS PORTUGAL
MAQUINASPORT, APARELHOS
DE DESPORTO, S.A.
Rua do Caminho Branco Lote 8,
ZI Oiã 3770-068 Oiã
Oliveira do Bairro (PORTUGAL)
Tel.: [phone]
Fax: [phone]
e-mail: [e-mail]
BH SERVICE PORTUGAL
Tel.: [phone]
Fax: [phone]
e-mail: [e-mail]
BH FITNESS MEXICO
BH Exercycle de México S.A. de
CV
Eje 132 / 136
Zona Industrial, 2A Secc.
78395 San Luis Potosí
S:L:P: MÉXICO
Tel.: [phone]
Fax: [phone]
www.bhlatam.com.mx
BH FITNESS CHINA
BH China Co., Ltd.
Block A, NO.68, Branch Lane
455, Lane 822,
Zhen Nan RD., Li Zi Yuan,
Putuo, Shanghai 200331, P.R.C.
Tel: [phone]
Fax:[phone]
e-mail: [e-mail]
BH GERMANY GmbH
Altendorfer Str. 526
45355 Essen
Tel: [phone]
e-mail:
[e-mail]
Kostenfreie Telefonnummer:
0800 0996655
Ersatzteile:
www.bhfitness.com
BH FITNESS UK
Tel: [phone]
e-mail:
[e-mail]
AFTER SALES – UK
Tel.: [phone]
e-mail:
[e-mail]
BH FITNESS FRANCE
SAV FRANCE
Tel : [phone]
Fax : [phone]
[e-mail]
BH SE RESERVA EL DERECHO A MODIFICAR LAS ESPECIFICACIONES DE SUS PRODUCTOS
SIN PREVIO AVISO.
SPECIFICATIONS MAY BE CHANGED WITHOUT PRIOR NOTICE DUE TO OUR PROGRAMME OF
CONTINUOUS PRODUCT DEVELOPMENT.
BH SE RÉSERVE LE DROIT DE MODIFIER LES SPECIFICATIONS DE SES PRODUITS SANS
PRÉAVIS.
BH BEHALT SICH DAS RECHT VOR, ÄNDERUNGEN DER MODELL-ANGABEN OHRE
VORHERIGE ANKÜNDIGUNG VORZUNEHMEN.
DATI TECNICI E COMMERCIALI RELATIVI AGLI ARTICOLI DEL PRESENTE CATALOGO
POSSONO ESSERE SOGGETIL A VARIAZIONI SENZA ALGUN PREAVVISO.
BH SE RESERVA O DIREITO A MODIFICAÇÀO ESPECIFICAÇOES DOS SEUS PRODUCTOS SEM
PRÉVIO AVISO.
DOOR KONSTANTE PRODUKTVERNIEUWING EN VERBETERING HOUDEN WIJ ONS HET
RECHT VAN WIJZIGING VOOR ZONDER VOORAFGAAND BERICHT. v3