Exitronix S900U Series User manual

S900U SERIES
INSTALLATION INSTRUCTIONS
800.533.3948 •www.barronltg.com
110070179 Rev 2 - 06/17 1
SAVE THESE INSTRUCTIONS!
READ CAREFULLY AND FOLLOW ALL INSTRUCTIONS FOR YOUR OWN SAFETY
• DISCONNECT AC POWER SUPPLY BEFORE SERVICING.
• Installation and servicing of this equipment should be performed by qualified service personnel only.
• Ensure the electricity connections conform to the National Electrical Code and local regulations if applicable.
• Do not mount near gas or electrical heaters.
• Equipment should be mounted in locations and at heights where it will not readily be subjected to tampering by
unauthorized personnel.
• The use of accessory equipment not recommended by the manufacturer may cause an unsafe condition. Any
modification or use of non-original components will void the warranty and product liability.
• Do not use this equipment for other than intended use.
INSTALLATION INSTRUCTIONS
Surface Ceiling & Wall Mounting
1. Use screwdriver to open front cover to connect
battery connector.
2. Feed AC supply wires through canopy center hole
and crossbar center hole.
3. Assemble canopy onto main body assembly with
(2) PM4*40 screws (supplied) and make proper
wire connections.
4. Electrical connections should be made inside junction
box. Cap all unused leads to prevent shorting.
• For 120VAC connect the black and white wires to
the building utility.
• For 277VAC connect the orange and white wires to
the building utility.
5. Attach crossbar to junction box, using screws if
needed. (Screws not provided)
6. Use (2) PM4*15 screws (supplied) to tighten canopy to
crossbar.
Front Cover
(PM4*40) Screws
(PM4*15) Screws

INSTALLATION INSTRUCTIONS
800.533.3948 •www.barronltg.com
10070179 Rev 2 - 06/17 2
7. Insert EXIT panel into main body assembly gently. If
EXIT panel is for single face, make sure EXIT letter
direction is correct.
Note: Refer to Chevron Placement section.
8. The EXIT panel may rotate any angle with 180° total
movement.
Surface End Mounting
1. Use screwdriver to open front cover to connect battery
connector.
2. Remove the hole plug from mounting end cap.
3. Pull out AC supply wires and feed wires through the
center hole of mounting end cap and center hold of
cross bar.
4. Assemble canopy onto main body assembly with (2)
PM4*15 screws (supplied) and make proper wire
connections.
5. Electrical connections should be made inside junction
box. Cap all unused leads to prevent shorting.
• For 120VAC connect the black and white wires to
the building utility.
• For 277VAC connect the orange and white wires to
the building utility.
6. Attach crossbar to junction box, using screws if
needed. (Screws not provided)
7. Use (2) PM4*40 screws (supplied) to tighten canopy to
crossbar.
8. Insert EXIT panel into main body assembly gently.
If EXIT panel is for single face, make sure EXIT letter
direction are correct.
Note: Refer to Chevron Placement section.
9. The EXIT panel may rotate any angle with 180° total
movement.
Rotate Angle
180° total
movement
Main Body
Assembly
(PM4*40)
Screws
Main body
Assembly
S900U SERIES

INSTALLATION INSTRUCTIONS
800.533.3948 •www.barronltg.com
10070179 Rev 2 - 06/17 3
(PB3*12) Screw
(PB3*12) Screw
Right end cap
Left end cap
Front cover
Recessed Ceilling Mounting
1. Use Screwdriver to open front cover to connect battery
connector. Remove test switch and LED indicator and
set aside for use at step 8.
2. Feed AC supply wires through canopy center hole.
3. Remove (1) PB3*12 screw from top of left and
right end caps.
4. Remove junction box cover and mount junction box
case on enclosure, use (2) TM4*8 screws. Feed AC
supply wire into junction box. Attach hanger bar brackets
using (2) PB3*15 and (2) TM4*8 screws. Attach hanger
bars to hanger bar brackets using (4) TM4*8 screws.
5. Position hanger bar bracket and hangers bar between
joists. Make sure hangers bar are oriented in the
correct position, then secure permanently with nails.
Hangers bar should be level with bottom of joists.
6. Adjust height of recessed kits vertically using adjusting
slots and then tighten all screws on adjusting slots
and hanger bar bracket.
7. Electrical connections should be made inside
junction box. Cap all unused leads to prevent
shorting.
• For 120VAC connect the black and white wires to
the building utility.
• For 277VAC connect the orange and white wires to
the building utility.
8. Connect test switch connector and LED indicator cables
via connectors.
9. Secure trimplate by using provided screws.
10. Insert EXIT panel into main body assembly gently. If
EXIT panel is for single face, make sure EXIT letter
direction is correct.
Note: Refer to Chevron Placement section.
11. The EXIT panel may rotate any angle with 180°
total movement.
Hanger Bar J-Box
Joists
Tightening screws after positioning
Trim Plate
Screws
(PB3*15) Screw
Screw (PB3*15)
(TM4*8) Screw
Screw (TM4*8)
Hangers Bar
Hanger Bar Bracket
Plastic Rivet
Juntion Box Cover
Juntion Box
(TM4*8) Screw
S900U SERIES

INSTALLATION INSTRUCTIONS
800.533.3948 •www.barronltg.com
10070179 Rev 2 - 06/17 4
Recessed Wall Mounting
1. Reference 1-16 steps in recessed ceiling mounting
for recessed wall mounting.
2. Recessed ceiling mounting rotated 90° becomes
recessed wall mounting.
Chevron Placement
• If chevron is needed remove only the
instruction film.
• If no chevron is needed, remove both the instuction
film and chevron together.
S900U SERIES