Exodraft XTP150G User manual

Your energy. Optimized.
Accessories
XTP150G
UK |Read and save these instructions!

Your energy. Optimized.
Accessories | XTP150G
Content
Product information 7
Scope of supply 7
Technical specications 8
Construction and components 9
Installation 11
Fitting 11
Electrical wiring 12
Operation and conguration 13
Troubleshooting 13
UK Conformity Assessed 14
Declaration of Conformity 15

Disposal
Electrical and electronic equipment (EEE) often contain materials, components and substances
that may harm the environment or be hazardous to your health. Products (WEEE) marked with
the ‘crossed-out wheeled bin’ symbol should be disposed of separately from other waste at
the end of its life. Though legislation may differ from country to country we strongly advise
that electrical and electronic waste is separated from other waste and disposed of according to
national legislation to protect the environment and personnel that may come into contact with
waste.
How to use this manual
This manual has been prepared based on the specific product and
contains relevant technical information and installations guides.
Accessories and spare parts are not covered by this manual.
Please refer to the individual manuals of these components.
This installation manual does not contain any system design documentation.
Failure to observe instructions marked with a danger symbol
may result in personal injury and/or damage to the product.
Errors and omissions excepted.

Disposal
Electrical and electronic equipment (EEE) often contain materials, components and substances
that may harm the environment or be hazardous to your health. Products (WEEE) marked with
the ‘crossed-out wheeled bin’ symbol should be disposed of separately from other waste at
the end of its life. Though legislation may differ from country to country we strongly advise
that electrical and electronic waste is separated from other waste and disposed of according to
national legislation to protect the environment and personnel that may come into contact with
waste.
How to use this manual
This manual has been prepared based on the specific product and
contains relevant technical information and installations guides.
Accessories and spare parts are not covered by this manual.
Please refer to the individual manuals of these components.
This installation manual does not contain any system design documentation.
Failure to observe instructions marked with a danger symbol
may result in personal injury and/or damage to the product.
Errors and omissions excepted.
Symbols
The following symbols may be used in the manual
to draw attention to danger or risk of personal
injury or damage to the product.
General prohibition
Failure to observe instructions marked with the prohibited
symbol may result in extreme danger or serious personal injury.
General warning
Failure to observe instructions marked with a danger symbol
may result in personal injury and/or damage to the product.
General attention
Marks a dangerous situation that, in the worst-case scenario,
can cause serious personal injury or significant damage to the product.
Electricity hazard/High Voltage
Marks a situation in which caution is advised due to the risk of high voltage electric
shock which can cause serious personal injury or significant damage to the product.
Connect an earth terminal to the ground
Failure to observe instructions marked with a danger symbol
may result in personal injury and/or damage to the product.
Permitted and approved
Permitted and approved method of installation.
Prohibited and not approved
Prohibited and not approved method of installation.

Warning
To minimise the risk of fire, electric shock, personal injury
and/or damage to the product please observe the following:
• Please always read the manual and only use the product in accordance with the
manufacturer’s instructions. If in doubt, contact one of the Exodraft specialized dealers.
• All installations must be carried out by properly qualifi ed personnel in accordance with
national legislation and regulations.
• This product must be earthed. Get assistance from an qualifi ed electrician when in doubt.
• This product must always be disconnected under the installation.
• Prior to servicing the product, disconnect the power and ensure that it cannot accidentally
be reconnected.
• Exodraft always recommends the use of a smoke alarm when a solid fuel open fire is
installed.
• If the Exodraft fan system has been designed for solid fuel/multi fuel installations, please
ensure that the design meets the requirements of BS EN15287-1. If this cannot be achie-
ved, a smoke alarm must be installed in the same room as the heat appliance.
UK
Your energy. Optimized.

UK |7
3112038_XTP150G_UK
Warning
To minimise the risk of fire, electric shock, personal injury
and/or damage to the product please observe the following:
• Please always read the manual and only use the product in accordance with the
manufacturer’s instructions. If in doubt, contact one of the Exodraft specialized dealers.
• All installations must be carried out by properly qualifi ed personnel in accordance with
national legislation and regulations.
• This product must be earthed. Get assistance from an qualifi ed electrician when in doubt.
• This product must always be disconnected under the installation.
• Prior to servicing the product, disconnect the power and ensure that it cannot accidentally
be reconnected.
• Exodraft always recommends the use of a smoke alarm when a solid fuel open fire is
installed.
• If the Exodraft fan system has been designed for solid fuel/multi fuel installations, please
ensure that the design meets the requirements of BS EN15287-1. If this cannot be achie-
ved, a smoke alarm must be installed in the same room as the heat appliance.
UK
Your energy. Optimized.
Product information
XTP150G is a high-precision pressure transducer specially developed for gas systems. It can also be used
with oil-red or solid-fuel systems.
In order to comply with the provisions of the Gas Appliances Directive 90/396/EEC:
• XTP150G must be connected to an EBC22 or
• XTP150G must be connected to a third party automatic gas control system with built-in “fail safe”
inputs (GAD)
Incorrect use may result in problems with soot, chimney res, etc. which might damage the product.
Please check out this site for advice about the product:
www.exodraft.com
Scope of supply
• XTP150G
• Silicone hose Ø 5 mm
• Installation manual and user instructions
Warranty
All Exodraft products are covered by a 2-year guarantee as per European consumer rights legislation. For
some countries an extended period of guarantee may apply depending on either national legislation or
other clearly stipulated conditions. Customer complaints must be handled by a specialised dealer or who-
lesaler (preferably where the Exodraft product has been bought originally). An updated list of Exodraft
specialised dealers can be found on our website for the country in question.
Exodraft products must always be installed by properly qualied personnel. Exodraft reserves the right to
change these guidelines without prior notice.
The warranty and liability does not cover instances regarding personal injury or damage to property or the
product that can be ascribed to one or more of the following causes:
• Failure to follow this installation and operation manual
• Incorrect installation, start-up, maintenance or servicing
• Improper repairs
• Unauthorised structural modications made to the product
• Installation of additional components that have not been tested/approved with the product
• Any damage resulting from continued use of the product despite an evident defect
• Failure to use original spareparts and accessories
• Failure to use the product as intended
• Exceeding or failure to meet the limit values in the technical data
• Force majeure

8|UK
Your energy. Optimized.
Technical specications
Technical data
Description XTP150G
H x W x D [mm] 90 x 115 x 55
Weight 237 g
Material: Box: Light grey polycarbonat
(PC)
Ingress Protection IP65
Pressure range 15 Pa – 150 Pa +/- 0.1%
Full scale
Ambient temperature -25 °C – +50 °C
Storage temperature: -25 °C – +50 °C
Connection terminals: Screw: max. 1.5 wire
Cable length Max. 100 m, min. 0.75 wire
Project:
Material:
Date:
Rev.:
Title:
Rev. No.: Ref.:
Format: A3
Weight:
Approved:
Draw. No.:
Sheet:
XTP150
19-11-2012
XTP150
PMN
DS/EN 22768 m
Unless otherwise specified tolerances are after
0,000 kg
1 of 4
108
55,1
55,1
80
80
28
14,2
Description Inputs
Supply 15 V DC – 35 V DC
Power Consumption,
absolut max: < 75 mA
Power Consumption,
nominel 60 mA
Description Outputs
Output 0-10 V DC, max. 10 mA
Alarm relay output (max) 48 V/2 A
Alarm relay contact
materiel AgCdO
Description Miscellaneous
Tolerable overload 20.000 Pa
Medium Air and exhaust gases
Responce time < 0.2s
Resolution from digital
sensor 0.01Pa
Repeatability +/- 0.1 % Full scale
Combined non-linearity
and hysteresis +/- 0.05 % Full scale
Offset longtime drift 1 year +/- 0.7 Pa max.
Temperature drift +/- 1.0 % Full scale
Transfer ratio 0.6 (250 Pa signal/150 Pa
output)
55
118
104
115
Fig. 1

UK |9
3112038_XTP150G_UK
ADIP switch
B Operating LED
CZero-point calibration button
DCable connector
E Mounting holes
F(-) Valve (P2)
G (+) Valve (P1)
HStatus LED
IConnecting terminals
JPressure transducer
Construction and components
The XTP150G is certied by GASTEC and have the certication number
PIN: 0063 BU1711
90
115
60 15
103640
Ø4,5
4x
NO NC
G
A
J
B
C
D
E
F
H
I
Fig. 2

10 |UK
Your energy. Optimized.
Key to g. 2-A
DIP switch Setting Function Factory setting OFF ON
ON RSN
1234
1 Calibration enabled OFF Calibration not possible Calibration possible
2 Not used OFF
3 Not used OFF
4 Not used OFF
Key to g. 2-B
Operating LED Indication Function
PIC # 1
PIC # 2
Flashing YELLOW Processor OK
Constant YELLOW Unit is not working
Not lit Unit is not working
Key to g. 2-C
Zero-point
calibration button
To activate Function
Press and hold for 5 s Calibration of zero point
Key to g. 2-D
Operating LED Indication Function
Constant GREEN Normal operation
Flashing RED Alarm (or DIP switch 1 is ON)