EXTBIKE Eagle EYE 1600LM User manual

Thank you for purchasing!
Welcome to the world of LED lighting ,
comprised of the highest quality materials
and craftsmanship, designed to provide
long reliable service.
To insure maximum experience and safety, familiarize yourself with
ALL aspects of your new light and battery system. Follow battery
charging instructions before use as systems are shipped with partially
charged batteries.

To insure maximum experience and safety, familiarize yourself with
ALL aspects of your new light and battery system.
1. Installation
2. Battery Usage and Charging
3. Light System and Operation
4. Warranty, Support, Customer Service
Caution:
1. Always unplug the light from the battery when not in use.
2. Use only the supplied charger with the battery.
Failure to follow these cautions will void the warranty and can cause
damage to the system.
A lighting system can make riding safer and you more visible,but
lights are no substitute for common sense. Ride within your
capability with consideration for the riding environment.
Installation:
The bike light comes with mounts for both handlebar and helmet.
There are two different sizes of rings to accommodate various sizes of
handlebars. When mounting the battery, locate a place that will keep
it and the wires protected from kinking or being pinched in the event
of a crash or in any other situation.The light is front weighted..
The light system is designed to be mounted on a handlebar or on the
enclosed helmet mount.Both mounts will use one of the rubber rings.
The battery may also be mounted using the attached Velcro strap.
When mounting the battery, insure adequate length of cable between
the battery and cable so that full freedom of movement of the mount
and does not pull on the battery, light or their connection or cause
the wire to become pinched or stressed. When mounting the
light,run the wire first over then handlebar and provide and extra half
wrap of cable in the even the light is twisted around the handlebar.
Excess wire maybe be wrapped around the handlebar or secured
within the battery Velcro strap.

When using the helmet mount for the light, the battery is designed to
be carried in a jacket pocket or a pack that you are wearing.
CAUTION: Do not connect a helmet mounted light to a bike
mounted battery.
Helmet mount: The helmet lamp mount may be used for a variety of
mounts with the included long Velcro straps. It is designed in such a
way that the light is easily removed using the rubber ring similar to
mounting on the handlebar.
You may find it advantageous to use both a handlebar mounted light
and a helmet mounted light. The head mount provides the additional
safety and flexibility to point the light quickly in any direction your
head points.
Aiming the light: When using any mounted light, insure that the
mounting does not project the beam directly into the eyes of
oncoming motorists or cyclists.
A temperature protection circuit will stop the light from overheating,
by stepping the output down if the light is left on full with no airflow
around it.
Handlebar Mount Helmet Mount

CAUTION
1. Battery Charger is for use only with the included Li-ion
battery pack. Trying to charge other than the included
battery pack may cause batteries to catch fire, overheat
leak or explode. Do not charge the battery with other
than the approved charger for this model.
2. Do not expose charger to rain, moisture or liquids.
3. Although the battery pack may be left on the charger
longer than 24 hours without damaging the battery
pack, if the battery will not be used for an extended
period, the battery life and capacity will be better
preserved by discharging the battery to approximately
half of capacity and then disconnecting and storing.
Every 3 to 4 months connect battery to light and use up
the remaining capacity in the battery and then charge to
50% capacity before continuing storage.
4. Disconnect the charger when not in use and before
connecting or removing batteries from charger.
5. Do not use charger or battery if, the wires or the
batteries or charger have become damaged.
Battery Usage and Charging:
Charge your battery pack in isolation and away from flammable
materials. Recharge immediately after use. Li-ion batteries do not
have a“memory effect”and can be left at full charge,although
battery life is extended if you follow CAUTION step #3 above.
1. Plug the battery pack into the charger
2. Connect the charger to the power outlet.
3. The LED on the charger will glow red when the battery is
being charged and turn to green when the battery is fully
charged.
4. When the charger LED turns green, you may unplug the
charger and then remove the battery pack from the charger.
Charging a fully depleted battery may take up to 5 hours.

Light System and Operation:
Operation Modes: Pressing the power button for seconds will turn the
light on. Each additional short press of this button switches the light from
one mode to the next, i.e. Two auxiliary lamps turn on; king lamp and
auxiliary lamps flashing alternately; king lamp turn on; three all lamps turn
on. Pressing the brightness button can change the brightness when two
auxiliary lamps turn on or king lamp turn on..
Turn light off: Pressing and holding the power button for seconds. If
leaving the light unattended, disconnect from the battery.
Check Battery Level: With the light attached to the battery, the operate
buttons leds will show the battery capacity automatically. The leds
illuminate green, yellow, orange, and red color to indicate the battery level
remaining.
Auxiliary
lamps
turn on
King lamp
turn on
All lamps
turn on
Flash
Approx Run Time
18 hours
6 hours
4 hours
Approx Lumens
600
1000
1600
Low Battery Level: The operation button leds will flashing with red color
when the battery level is low and the light will automatically turn off when
the battery level is too low. This system protects the battery from damage,
but since it draws a small amount of current, and can drain the battery
beyond the minimum voltage for the battery,
The light must be disconnected from battery when the button leds
flashing with red color or within 5 minutes of they flashing. Do not
wait until the light goes completely out as this will greatly
reduce the number of charge cycles that the battery can be
used and can render the battery unusable. Disconnect the
battery when not in use or stored.

Model No: EAGLE EYE Specifications
Type: Bicycle light, Headlamp
Our product with unique and stylish streamline design, uses one CREE
T6 XM-L ultra bright LED, two pcs CREE R4 LED and high efficiency
orange peel reflector to provide super bright light; exquisite
anodizing and quality workmanship, long lasting Li-ion battery
provides 8.4V 5500mA/h or 7.4V 6000mA/h capacity, and waterproof
rubber pack to provide perfect protection, making your night
adventure more enjoyable.
1. Waterproof headlamp Brightness: 1600LM
2. Low power consumption
3. Material: Aircraft aluminum
4. Finishing: hard anodized
5. Fluorescent waterproof indicator ring for greater night visibility
6. Color: black
7. LED : CREE 1XT6+2XR4 Flux::1600Lumens
8. LED life span: 50,000hours
9. Battery: 8.4 V 5500mah Li-ion or 7.4V 6000mah Li-pol
Battery Discharge Times : 1080 minutes (Two auxiliary lamps turn on)
360 minutes (King lamp turn on)
240 minutes (Three all lamps turn on
Charge Time :5~6 H
Low Power warning: red light warning (blue fluorescent ring changes to red)
Lighting Modes: Two auxiliary lamps turn on; king lamp and auxiliary lamps
flashing alternately; king lamp turn on; three all lamps turn on.
Waterproof Grade: IP65

Warranty Card:
Our product quality is controlled strictly in accordance within the
standards of our quality certification program. To ensure that all
users enjoy the product, we commits to all users the following:
1). One year warranty Within one year from purchase date, under
normal use, the consumer will be provided free warranty service for
any quality related problems.
2). Lifetime limited repair: We will provide paid warranty service after
the initial one year warranty. The cost of this service is for the actual
replacement part without any additional labor fees. The warranty is
limited to existing stocked models, parts and accessories.
When requesting warranty service, customer should present this page
along with the original purchase receipt or numbers provided to the
dealer or online retailer where purchased. The dealer or retailer will
handle warranty claim.
Warranty Service Exclusions:
A) Any damages that are caused by other than normal use, including, but
not limited to physical damages.
B) Any user modification, repairs or disassembly of the product
without factory authorization.
C) Missing warranty card or valid receipt documents
Model EAGLE EYE -- 1600 Lumen light