Extech Instruments AN310 User manual

USERGUIDE


LargeVaneCFM/CMM
Anemometer/Psychrometer


ModelAN310
contact:
[email protected]
www.ponpe.com

AN310-en-GB_V1.5 11/15
2
Introduction
CongratulationsonyourpurchaseoftheExtechAN310VaneAirflowAnemometerPsychrometer.
ThisinstrumentmeasuresAirVelocity,AirFlow(volume),AirTemperature,RelativeHumidity,Wet
BulbTemperature,andDewPointTemperature.Thelarge,easy‐to‐readbacklitLCDincludes
primaryandsecondarydisplaysplusnumerousstatusindicators.Theoptionalroundandsquare
airflowconeallowsforquickvolumemeasurements.Thismeterisshippedfullytestedand
calibratedand,withproperuse,willprovideyearsofreliableservice.Pleasevisitourwebsite
(www.extech.com)tocheckforthelatestversionofthisUserGuide,ProductUpdates,and
CustomerSupport.
CAUTIONS
Improperuseofthismetercancausedamagetothemeterandpersonalinjury.Readand
understandthisusermanualbeforeoperatingthemeter.
Inspecttheconditionoftheprobeandthemeterforanydamagebeforeoperatingthe
meter.Repairorreplacedamagebeforeuse.
Iftheequipmentisusedinamannernotspecifiedbythemanufacturer,theprotection
providedbytheequipmentmaybeimpaired.
Thisdeviceshouldnotbemadeavailabletochildren.Itcontainshazardousobjectsaswell
assmallpartsthatcanbeaccidentallyswallowed.Themeter’sbatteriesandpacking
materialcanalsobedangeroustochildren.
Intheeventthatthemeteristobeunusedforanextendedperiodoftime,removethe
batteriestoprotectagainstbatteryleakage.
Expiredordamagedbatteriescanbehazardousifallowedtocomeincontactwithskin.Use
suitablehandprotectioninsuchcases.
Donotshortcircuitbatteriesorputbatteriesinfire.
www.ponpe.com
contact:
[email protected]

AN310-en-GB_V1.5 11/15
3
MeterDescription
MeterDescription(front)
1. ToplineLCDdisplayreading
2. BottomlineLCDdisplayreading
3. U/modeAVGanduparrowbutton
4. L/modeanddownarrowbutton
5. ON‐OFF(Power)andSETbutton
6. HOLD,MAX‐MIN,andleftarrow(Enter)button
7. Unitofmeasuresymbolforlowerdisplayrow
8. Unitofmeasuresymbolforupperdisplayrow
9. AirVelocityVane
MeterDescription(rear)
10. Airtemperatureandhumiditysensors
11. Batterycompartment















contact:
[email protected]
www.ponpe.com

AN310-en-GB_V1.5 11/15
4
SET
HOLD
MAX/MIN
U/mode
AVG
▲
L/mode
▼
U/mode
AVG
▲
BriefKeypadDescription

PressmomentarilytoswitchthemeterONorOFF.Pressandholdthisbuttonfor2
secondstoenterorexittheSetupmode(refertoSetupmodesectionfordetails).

oPressmomentarilytofreezethedisplayedreading(HOLDiconswitchesON);press
againmomentarilytoexittheHOLDmode(HOLDiconswitchesOFF)
oPressandholdfor2secondstodisplaytheMIN(minimum)reading;pressandhold
againtodisplaytheMAX(maximum)reading;Pressandholdathirdtimetoexit
oThisbuttonisalsousedintheAVERAGEmode(forrecordingreadingsoneatatime
orfora‘timed’recordingsession)andintheSETUPmode(forconfiguringthe
meter).PleasereviewtheAVERAGEandSETUPmodesectionsfordetails


PressmomentarilytotoggleRHandAirVelocityreadings.Pressandholdfor2seconds
toaccesstheMulti‐PointAverageandTimedAveragemodes(theAVGiconswitches
ON).Detailedinstructionsforthesemodesareprovidedlaterinthisguide.Inthe
Setupmodepresstoselectacategoryortoincreaseavalue(refertoSetupmodelater
inthisguide)


Presstotogglethelowerdisplaybetweenairtemperature,airvolume,wetbulb
temperature,anddewpointtemperaturereadings;AlsousedintheMulti‐Point
Average,TimedAverage,andSetupmodes;refertotheAVERAGEandSETUPmodes
sectionslaterinthisguide


 
+WiththemeterswitchedOFF,pressandholdthesetwobuttonstodisable
AutoPowerOFF.DetailedAUTOPOWEROFF(Sleepmode)instructionsare
providedlaterinthisguide

contact:
[email protected]
www.ponpe.com

AN310-en-GB_V1.5 11/15
5
DisplayLayout
1. LowerDisplaydigits(airvolume,temperature,timer,ormenuparameterdisplays)
2. UpperDisplaydigits(airvelocity,humidity,ormenudisplayparameters)
3. OptionalConeorFunnelattachmenticon
4. Unitsofmeasureforductareaprogramming
5. Vaneindicator(flashesverybrieflyonpowerup)
6. DisplayHOLDicon
7. MAXmodeicon
8. MINmodeicon
9. Recordingicon
10. ElapsedTimericon
11. AVGmodeicon
12. Batterystatusicon
13. Unitofmeasureicons*

*Fulllistshown.Availableunitsofmeasureiconsvarybymodel.
contact:
[email protected]
www.ponpe.com

AN310-en-GB_V1.5 11/15
6
Operation
AirVelocityandAirVolumeMeasurements
1. SwitchthemeterONbypressingthePOWER buttonmomentarily.PressthePOWER
buttonagaintoswitchthemeterOFF.
2. Notethatthemeterwillautomaticallyenterthesleepmodeafter20minutesofinactivity.
Todisablethisfeature:withthemeterOFF,pressandholdthePOWERandtheU/mode
buttonsfor2seconds.TheLCDwilldisplay'n'asitswitchesON.Nowthesleepmodeis
disabledandtheusermustpressthePOWERbuttonmomentarilytoswitchthemeterOFF.
3. WhenthemeterisON,theupperdisplaycanindicate
airvelocityorrelativehumidity(usetheU/modebutton
totoggle).Thelowerdisplaydigitscanindicateairflow,
dewpointtemperature,wetbulbtemperature,orair
temperature(usetheL/modebuttontoscroll).
4. Placethesensorintheairstream.Theairmustenter
thevanefromtherearofthemeter.TheAir
TemperatureandRelativehumiditysensorsarelocatedatthecenterofthevaneontherear
ofthemeter.
5. ReadthemeasurementdataontheLCD.Airvelocityreadingsareindicatedinmetersper
second(m/s)orfeetperminute(fpm).Temperaturereadings(air,dewpoint,orwetbulb)
areindicatedin°C/°F.RelativeHumidityisindicatedin%.Airflow(volume)isindicatedin
CFM(cubicfeetperminute)orCMM(cubicmetersperminute).UsetheL/modebutton(for
lowerdisplay)andtheU/modebutton(forupperdisplay)toscrollthroughthedisplayed
readingoptions.
6. TochangebetweenImperialandMetricunitsofmeasurerefertotheSETUPModesection.
7. TomeasuretheAirVolumeofaduct,firstmeasuretheduct’sarea(seetheAppendixfor
areacalculations)andthenentertheareavalueinthemeter’sSETUPmodeinin2orcm2.
Aftertheareavaluehasbeenentered,usetheL/modebuttontoscrolltotheairvolume
display(CMM/CFM)onthelowerdigits.Placethemeterinairstreamtomeasurevolume.
8. Optional:measureAirVolumewithanairflowConeorSquareadaptorbyfirstattachingone
oftheadaptorstothemeter(theoptionalconeadaptorkitincludesaroundandasquare
cone;kitpartnumberAN300‐C).Themeterwillautomaticallyrecognizethattheadaptoris
attachedtothemeterandaconeiconwillappearonthedisplay.
Note:regardlessoftheAREAsettingintheSETUPmode,themeterwilldefaulttothe
dimensionsofthevaneopening.Ensurethattheairflowadaptoriswellmountedandlocked
beforetakingmeasurements.
LCDbacklight
PresstheU/modebuttontoswitchONtheLCDbacklight.Thebacklightwillautomaticallyswitch
OFFafterapproximately10secondstoconservebatterypower.Notethatthebacklighting
switchesONautomaticallywhenthemeterisswitchedONbytheuser.
www.ponpe.com
contact:
[email protected]

AN310-en-GB_V1.5 11/15
7
RelativeHumidity,WetBulb,andDewPointMeasurements
Therelativehumiditysensorisbuiltintothecenterofthevane(rearofmeter)andcanbeusedto
measurerelativehumidity,dewpointandwetbulbtemperatures.
1. PressU/modetoswitchtothe%RHdisplayifnecessary.Themeasuredhumidityreadings
willbedisplayedontheupperLCDdigits.
2. UsetheL/modebuttontoscrollthroughairtemperature,dewpointtemperature,wetbulb
temperature,andairvolumereadings.
3. Tomeasurethehumidityusinganoffsetreferencevalue,pleaseaccesstheSetupmodeand
inputtheoffsetvalueasdescribedintheSetupmodesection.TheLCDwilldisplaythe
measuredvalueminustheoffsetvalueoncetheoffsetisprogrammedintheSetupmode.
DataHoldMode
1. PresstheHOLDbuttonfromthenormaloperatingmodetofreezethecurrentmeasurement.
2. The‘HOLD’iconwillappearatthetopoftheLCDdisplay.
3. PressHOLDagaintoreturntonormaloperation.The‘HOLD’iconwillswitchOFFandthe
meterwillreturntodisplayingreadingsinrealtime.
MAX/MINMode
TheMAX‐MINfeaturerecordsthehighest(MAX)andlowest(MIN)readingscapturedsincethe
MAX‐MINmodewasaccessed.
1. PressandholdtheMAX/MINbuttonfor2secondstobegindisplayingthelowest(minimum)
readingsencounteredsincethismodewasaccessed.The‘MIN’iconwillappearatthetopof
theLCDdisplayindicatingthatthereadingsshownarethelowestmeasured.
2. PressandholdtheMAX/MINbuttonagainfor2secondstodisplaythemaximumreadings
encountered.The‘MAX’iconwillappearontheLCD.
3. Pressandholdthisbuttonagainfor2secondstoreturntothenormalmodeofoperation
(the‘MIN’and‘MAX’iconsshouldswitchOFF).
4. WhileviewingtheMAXorMINdata,usetheL/modebuttontoswitchthedisplaysothatthe
AirVolumeMINandMAXreadingscanbeviewedalso.
5. PressandholdMAX/MINfor2secondstoreturntothenormaloperationmode.
Multi‐PointAverageMode
1. FromthenormaloperatingmodepresstheU/modebuttonfor2secondstoenterMulti‐
PointAveragemode(theAVGdisplayiconandtheassociatedblackdot•willswitchON).
2. PresstheHOLDbuttonmomentarilytorecordonereading.Theupperdisplaydigitswill
showthereading’smemorylocationnumberandthelowerdisplaywillshowthemeasured
value.PresstheHOLDbuttonagaintotakeandstoreanotherreading;thememorylocation
numberwillincrementbyoneandthecurrentreadingwillbestoredinthisnewmemory
location.Themetercanstoreupto19,999pointsinmemory.
3. PressU/modemomentarilytoseethemulti‐pointmean(average)forallofthereadings
recordedduringthesession(the'•AVG'displayiconwillflashduringthisprocess).
4. PressL/modetoviewtheaveragereadingfortheotheravailableparameters.
5. PressU/modemomentarilytoreturntothenormaloperatingmode.
www.ponpe.com
contact:
[email protected]

AN310-en-GB_V1.5 11/15
8
TimedAverageMode
1. Fromthenormaloperatingmode,pressandholdtheU/modebuttonfor2secondstoenter
theMulti‐PointAveragemodefirstandthenpressU/modeonemoretimemomentarilyto
entertheTimedAverageMode(theAVGandtheelapsedtimer iconswillswitchON).
2. PressHOLDtobeginrecording.Theelapsedtimerstarts(asshownontheupperdisplay
digits)andtheclockiconflashesonandoff.Thelongestamountoftimethemetercan
operateinTimedAverageModeis19,999seconds.
3. PressU/modetostoptheclockandtocalculatethetimedaverage.TheupperLCDwill
displaytheelapsedtimeandthelowerLCDwillshowtheaveragedreadings.TheLCDwill
flashthe'AVG'andtheelapsedtimericons.
4. PressL/modetoviewtheaverageforotheravailablemeasurements.
5. PressU/modetoreturntothenormaloperatingmode.

SetupMode
EnteringSetupMode
PressandholdthePOWERSETbuttonfor2secondstoenterSetupmode.Twooptionsare
available:P1.0:UnitandP2.0:AREA.
Usetheup/downbuttonstotogglebetweenP1.0UNITandP2.0AREAoptions.
P1.0:UnitSelection
1. Onceinsetupmode,attheP1.0UNITdisplay,momentarilypresstheHOLDbuttontoenter
theP1.0UNITmenu.
2. Useeitherarrowbuttontoswitchbetweenmetricandimperialunits.Theavailableunits
are:airvelocity(m/s,fpm),temperature(C,F),airvolume(CMM,CFM),andareasize(cm²,
inch²).
3. PressHOLDmomentarilytoreturntotheP1.0display.
4. PresseitherarrowbuttontomovetotheP2.0AREAoptionandfollowthestepsbelow.
P2.0:AreaSizeSelection(entersquareinchesorsquarecentimeters)
1. Insetupmode,fromtheP2.0AREAdisplay,pressHOLDtoentertheAREAsettingmenu.The
LCDwillshow‘99999’inthelowerdisplaywiththefirstdigitflashing.
2. Usetheuparrowbuttonchangetheflashingdigit(from0through9).
3. Usethedownarrowbuttontomovetothenextdigit.Usetheuparrowbuttonagainto
changetheflashingdigit.ContinueinthiswayuntilthedesiredAREAvalueisdisplayed.
4. PresstheHoldbuttonagainmomentarilytostorethevalueandtoreturntotheP2.0display.
5. PresseitherarrowbuttontomovetotheP3.0RHOFFSEToptionandfollowthestepsbelow.
P3.0:RelativeHumidity(RH)OffsetSelection
1. WheninsetupmodeP3.0pressHOLDtoentertheRHoffsetsetting.TheLCDwillshow0.0
RHintheupperdisplay.
2. PressU/modetoincreaseoffsetvalueandL/modetodecreaseoffset.
3. PresHOLDoncemoretoreturntoP3.0.
4. PressandholdthePOWERSETbuttonfor2secondstoreturntothenormaloperating
mode.
contact:
[email protected]
www.ponpe.com

AN310-en-GB_V1.5 11/15
9
BatteryReplacement
WhenappearsontheLCD,theAAAbatteriesmustbereplaced.Thebatterycoverislocated
onthebackofthemeter.
1. Opentherearbatterycompartmentbycarefullypullingdownonthecompartment’slatch.
2. Thebatterycompartmentcovershouldbecompletelyremovedbeforeproceeding.
3. Replacethefour(4)1.5V‘AAA’batteriesensuringproperpolarity.
4. Closethebatterycompartmentbeforeattemptingtousethemeter.

Neverdisposeofusedbatteriesorrechargeablebatteriesinhouseholdwaste.
Asconsumers,usersarelegallyrequiredtotakeusedbatteriestoappropriate
collectionsites,theretailstorewherethebatterieswerepurchased,orwherever
batteriesaresold.
Disposal:Donotdisposeofthisinstrumentinhouseholdwaste.Theuseris
obligatedtotakeend‐of‐lifedevicestoadesignatedcollectionpointforthedisposal
ofelectricalandelectronicequipment.

OtherBatterySafetyReminders
oNeverdisposeofbatteriesinafire.Batteriesmayexplodeorleak.
oNevermixbatterytypes.Alwaysinstallnewbatteriesofthesametype.
www.ponpe.com
contact:
[email protected]

AN310-en-GB_V1.5 11/15
10
Specifications
AirVelocityRangesResolutionAccuracy
m/s(meterspersec)0.2–30m/s0.01m/s±(1.5%rdg+0.3m/s)
fpm(feetperminute)40–5900fpm1fpm±(1.5%rdg+59fpm)
RelativeHumidityRangeResolutionAccuracy
RH0.1%‐99.9%RH0.1RH±3%RH(10‐90%RH)
±5%RH(<10%or>90%)
AirFlowRangesResolutionAreaRange
CMM(cubicmeters/min)0‐99999m3/min0.1upto9999.9
then1.00to99999cm2
CFM(cubicft/min)0‐99999ft3/min0.1upto9999.9
then1.00to99999in2
TemperatureRangesResolutionAccuracy
oC/oF
AirandWetBulb:
‐20to60oC(‐4to140oF)
DewPoint:
‐5to60oC(23to140oF)
0.1oC/oF
±0.6°C(‐20to50°C)
±1.2°C(51to60°C)
±1.1°F(‐5to122°F)
±2.2°F(123to140°F)
CircuitCustomLSImicroprocessor
DisplayDualfunction13mm(0.5")4‐digitLCD
Samplingrate1readingpersecondapprox.
Airvelocity/flowsensor Conventionalangledvanearmswithlow‐frictionballbearing
SensorsNTC‐typeprecisionthermistors
AutomaticPoweroffAutoshutoffafter20minutestopreservebatterylife(sleepmode)
OperatingTemperature0°Cto50°C(32°Fto122°F)
StorageTemperature‐10to50oC(14to122oF)
OperatingHumidity<80%RH
StorageHumidity<90%RH
OperatingAltitude2000meters(7000ft)maximum
BatteryPowerFour(4)‘AAA’1.5Vbatteries
BatteryLife>40hours
Batteryconsumption8.3mADC(approx.)
Weight725g(1.6lbs.)includingbatteryandprobe
DimensionsMaininstrument:269x106x51mm(10.6x4.2x2”)
Vaneinnerdiameter:100mm/3.94inches
OptionalAirFlowAdaptors:
Round:210mm(8.3”)Diameter
Square:346x346mm(13.6x13.6”)
contact:
[email protected]
www.ponpe.com