ExtremeSwitching 3600 Series User manual

Using CLI and EDM on Ethernet Routing
Switch 3600 Series
Release 6.3
9035797 Rev AA
August 2019

© 2017-2019, Extreme Networks, Inc.
All Rights Reserved.
Legal Notice
Extreme Networks, Inc. reserves the right to make changes in
specifications and other information contained in this document and
its website without prior notice. The reader should in all cases consult
representatives of Extreme Networks to determine whether any such
changes have been made.
The hardware, firmware, software or any specifications described or
referred to in this document are subject to change without notice.
Trademarks
Extreme Networks and the Extreme Networks logo are trademarks or
registered trademarks of Extreme Networks, Inc. in the United States
and/or other countries.
All other names (including any product names) mentioned in this
document are the property of their respective owners and may be
trademarks or registered trademarks of their respective companies/
owners.
For additional information on Extreme Networks trademarks, please
see: www.extremenetworks.com/company/legal/trademarks
Open Source Declarations
Some software files have been licensed under certain open source or
third-party licenses. End-user license agreements and open source
declarations can be found at: www.extremenetworks.com/support/
policies/software-licensing

Contents
Chapter 1: About this Document............................................................................................. 5
Purpose.................................................................................................................................. 5
Conventions............................................................................................................................ 5
Text Conventions............................................................................................................... 5
Documentation and Training..................................................................................................... 7
Getting Help............................................................................................................................ 8
Providing Feedback to Us........................................................................................................ 9
Chapter 2: New in this document.......................................................................................... 10
Chapter 3: Command Line Interface Fundamentals............................................................ 11
CLI Command Modes............................................................................................................ 11
Command completion............................................................................................................ 13
default command operator..................................................................................................... 14
no command operator............................................................................................................ 16
GREP with CLI show command.............................................................................................. 17
CLI help................................................................................................................................ 17
Getting EDM online help files for embedded EDM.................................................................... 19
Downloading help files..................................................................................................... 19
Command Line Interface Procedures...................................................................................... 20
CLI Access Procedures................................................................................................... 20
Configuring the path to the help files using CLI.................................................................. 20
CLI configuration files...................................................................................................... 21
GREP CLI show command filters...................................................................................... 26
Enabling the Web server using CLI................................................................................... 30
Disabling the Web server using CLI.................................................................................. 31
Displaying the Web server status using CLI....................................................................... 31
Chapter 4: Enterprise Device Manager concepts................................................................ 32
Tested browsers.................................................................................................................... 33
Memory requirements............................................................................................................ 33
Interface components............................................................................................................ 33
Switch summary view...................................................................................................... 34
Device Physical View....................................................................................................... 34
EDM window................................................................................................................... 35
Single port configuration for EDM..................................................................................... 42
Multiple Port Configuration for EDM.................................................................................. 45
Online help........................................................................................................................... 46
Enterprise Device Manager procedures................................................................................... 47
Starting EDM.................................................................................................................. 47
Using shortcut menus...................................................................................................... 47
Navigating around EDM................................................................................................... 48
August 2019 Using CLI and EDM on Ethernet Routing Switch 3600 Series 3

Undocking tabs............................................................................................................... 48
Docking tabs................................................................................................................... 49
Editing a dialog box......................................................................................................... 49
Inserting an entry in a dialog box...................................................................................... 49
Deleting an entry from a dialog box................................................................................... 50
Editing an object using the shortcut menu......................................................................... 50
Editing file system elements............................................................................................. 50
Configuring multiple interface ports using EDM - Example 1............................................... 51
Configuring multiple ports using EDM - Example 2............................................................. 51
Graphing statistics........................................................................................................... 52
Configuring the help file path using EDM........................................................................... 53
Displaying USB file information using EDM........................................................................ 53
Saving current configuration to flash memory manually using EDM..................................... 53
Enterprise Device Manager configuration files......................................................................... 54
ASCII configuration file management using EDM............................................................... 55
Binary configuration file management using EDM.............................................................. 58
Contents
August 2019 Using CLI and EDM on Ethernet Routing Switch 3600 Series 4

Chapter 1: About this Document
This section discusses the purpose of this document, the conventions used, ways to provide
feedback, additional help, and information regarding other Extreme Networks publications.
Purpose
This document describes how to use the Command Line Interface (CLI) and Enterprise Device
Manager (EDM) to configure the Extreme Networks Ethernet Routing Switch 3600 Series.
Conventions
This section discusses the conventions used in this guide.
Text Conventions
The following tables list text conventions that can be used throughout this document.
Table 1: Notice Icons
Icon Alerts you to...
Important: A situation that can cause serious inconvenience.
Note: Important features or instructions.
Tip: Helpful tips and notices for using the product.
Danger: Situations that will result in severe bodily injury; up to
and including death.
Warning: Risk of severe personal injury or critical loss of data.
Caution: Risk of personal injury, system damage, or loss of
data.
August 2019 Using CLI and EDM on Ethernet Routing Switch 3600 Series 5

Table 2: Text Conventions
Convention Description
Angle brackets ( < > ) Angle brackets ( < > ) indicate that you choose the
text to enter based on the description inside the
brackets. Do not type the brackets when you enter
the command.
If the command syntax is cfm maintenance-
domain maintenance-level <0-7> , you can
enter cfm maintenance-domain
maintenance-level 4.
Bold text Bold text indicates the GUI object name you must act
upon.
Examples:
•Click OK.
• On the Tools menu, choose Options.
Braces ( { } ) Braces ( { } ) indicate required elements in syntax
descriptions. Do not type the braces when you enter
the command.
For example, if the command syntax is ip address
{A.B.C.D}, you must enter the IP address in
dotted, decimal notation.
Brackets ( [ ] ) Brackets ( [ ] ) indicate optional elements in syntax
descriptions. Do not type the brackets when you
enter the command.
For example, if the command syntax is show clock
[detail], you can enter either show clock or
show clock detail.
Ellipses ( … ) An ellipsis ( … ) indicates that you repeat the last
element of the command as needed.
For example, if the command syntax is
ethernet/2/1 [ <parameter>
<value> ]..., you enter ethernet/2/1 and as
many parameter-value pairs as you need.
Italic Text Italics emphasize a point or denote new terms at the
place where they are defined in the text. Italics are
also used when referring to publication titles that are
not active links.
Plain Courier Text Plain Courier text indicates command names,
options, and text that you must enter. Plain Courier
text also indicates command syntax and system
output, for example, prompts and system messages.
Table continues…
About this Document
August 2019 Using CLI and EDM on Ethernet Routing Switch 3600 Series 6

Convention Description
Examples:
•show ip route
•Error: Invalid command syntax
[Failed][2013-03-22 13:37:03.303
-04:00]
Separator ( > ) A greater than sign ( > ) shows separation in menu
paths.
For example, in the Navigation tree, expand the
Configuration > Edit folders.
Vertical Line ( | ) A vertical line ( | ) separates choices for command
keywords and arguments. Enter only one choice. Do
not type the vertical line when you enter the
command.
For example, if the command syntax is access-
policy by-mac action { allow | deny } ,
you enter either access-policy by-mac action
allow or access-policy by-mac action
deny, but not both.
Documentation and Training
To find Extreme Networks product guides, visit our documentation pages at:
Current Product Documentation www.extremenetworks.com/documentation/
Archived Documentation (for earlier
versions and legacy products)
www.extremenetworks.com/support/documentation-archives/
Release Notes www.extremenetworks.com/support/release-notes
Hardware/Software Compatibility
Matrices
https://www.extremenetworks.com/support/compatibility-matrices/
White papers, data sheets, case
studies, and other product resources
https://www.extremenetworks.com/resources/
Training
Extreme Networks offers product training courses, both online and in person, as well as specialized
certifications. For more information, visit www.extremenetworks.com/education/.
Documentation and Training
August 2019 Using CLI and EDM on Ethernet Routing Switch 3600 Series 7

Getting Help
If you require assistance, contact Extreme Networks using one of the following methods:
Extreme
Portal
Search the GTAC (Global Technical Assistance Center) knowledge base, manage
support cases and service contracts, download software, and obtain product
licensing, training, and certifications.
The Hub A forum for Extreme Networks customers to connect with one another, answer
questions, and share ideas and feedback. This community is monitored by Extreme
Networks employees, but is not intended to replace specific guidance from GTAC.
Call GTAC For immediate support: 1-800-998-2408 (toll-free in U.S. and Canada) or +1
408-579-2826. For the support phone number in your country, visit:
www.extremenetworks.com/support/contact
Before contacting Extreme Networks for technical support, have the following information ready:
• Your Extreme Networks service contract number and/or serial numbers for all involved Extreme
Networks products
• A description of the failure
• A description of any action(s) already taken to resolve the problem
• A description of your network environment (such as layout, cable type, other relevant
environmental information)
• Network load at the time of trouble (if known)
• The device history (for example, if you have returned the device before, or if this is a recurring
problem)
• Any related RMA (Return Material Authorization) numbers
Subscribing to Service Notifications
You can subscribe to email notifications for product and software release announcements,
Vulnerability Notices, and Service Notifications.
1. Go to www.extremenetworks.com/support/service-notification-form.
2. Complete the form with your information (all fields are required).
3. Select the products for which you would like to receive notifications.
Note:
You can modify your product selections or unsubscribe at any time.
4. Click Submit.
About this Document
August 2019 Using CLI and EDM on Ethernet Routing Switch 3600 Series 8

Providing Feedback to Us
Quality is our first concern at Extreme Networks, and we have made every effort to ensure the
accuracy and completeness of this document. We are always striving to improve our documentation
and help you work better, so we want to hear from you! We welcome all feedback but especially
want to know about:
• Content errors or confusing or conflicting information.
• Ideas for improvements to our documentation so you can find the information you need faster.
• Broken links or usability issues.
If you would like to provide feedback to the Extreme Networks Information Development team, you
can do so in two ways:
• Use our short online feedback form at https://www.extremenetworks.com/documentation-
feedback/.
• Email us at [email protected].
Please provide the publication title, part number, and as much detail as possible, including the topic
heading and page number if applicable, as well as your suggestions for improvement.
Providing Feedback to Us
August 2019 Using CLI and EDM on Ethernet Routing Switch 3600 Series 9

Chapter 2: New in this document
There are no feature changes in this document.
August 2019 Using CLI and EDM on Ethernet Routing Switch 3600 Series 10

Chapter 3: Command Line Interface
Fundamentals
This chapter describes the Command Line Interface (CLI).
CLI is an industry standard command line interface that you can use for single-device management.
CLI Command Modes
Command Line Interface (CLI) command modes provide specific sets of CLI commands. When you
log onto the switch, you are in User EXEC mode with limited commands. While in a higher mode,
you can access most commands from lower modes, except if they conflict with commands of your
current mode.
There are two categories of CLI commands: show commands and configuration commands. Show
commands can be used from multiple command modes with the same results; they show the same
configuration information regardless of the command mode from which the show command is used.
Configuration command results, however, may be dependent on the command mode from which a
configuration command is used. For example, an enable command used in Global Configuration
mode will enable a feature globally for all devices, while the same command used from one of the
interface command modes will enable a feature for a specific interface only.
Your user authorization credentials determine what commands are available to you in Privileged
EXEC mode and all higher level modes. If you have read-only access, you cannot progress beyond
User EXEC mode. If you have read-write access, you can progress through all available modes.
The CLI commands for navigating from lower to higher level modes are listed in the following table.
To navigate from higher to lower level modes, use the following commands:
•exit to navigate from a higher level mode to a lower level mode, down to Privileged EXEC
mode
•end from any command mode directly to Privileged EXEC mode
•disable to navigate from Privileged EXEC mode to User EXEC mode
•logout to terminate the CLI session from any command mode
The following table describes the various command modes, including the CLI commands to access
and to exit each mode.
August 2019 Using CLI and EDM on Ethernet Routing Switch 3600 Series 11

Table 3: CLI command modes
Command mode and sample
prompt
Entrance commands Exit commands
User Executive
Switch>
No entrance command, default
mode
exit
or
logout
Privileged Executive
Switch#
enable exit
or
logout
Global Configuration
Switch (config)#
From Privileged Executive mode,
enter
configure terminal
To return to Privileged Executive
mode, enter
end
or
exit
To exit CLI completely, enter
logout
Interface Configuration
Switch (config-if)#
From Global Configuration mode:
To configure a port, enter
interface ethernet <port
number>
To configure a VLAN, enter
interface vlan <vlan
number>
To configure a loopback, enter
interface loopback
<loopback number>
To return to Global Configuration
mode, enter
exit
To return to Privileged Executive
mode, enter
end
To exit CLI completely, enter
logout
Router Configuration
Switch (config-router)#
From Global Configuration mode:
To configure RIP, enter router
rip
To return to Global Configuration
mode, enter
exit
To return to Privileged Executive
mode, enter
end
To exit CLI completely, enter
logout
Application Configuration
Switch (config-app)#
From Global, or Interface
Configuration mode, enter
To return to Global Configuration
mode, enter
Table continues…
Command Line Interface Fundamentals
August 2019 Using CLI and EDM on Ethernet Routing Switch 3600 Series 12

Command mode and sample
prompt
Entrance commands Exit commands
application exit
To return to Privileged Executive
mode, enter
end
To exit CLI completely, enter
logout
Command completion
The CLI provides potential command completions to the command string. Completions are provided
by using a question mark (?) or by using the CLI autocompletion feature.
? command completion
The ? command completion is available for any valid command. By typing a command and using
a ? as the last argument in the command, the system returns a list of possible command
completions from the point of the ?. A short description is provided with each possible completion.
Example
If you enter the following command:
Switch:1(config-ospf)#redistribute ?
CLI provides a list of completions for the redistribute ? command.
Switch:1(config-ospf)#redistribute ?
direct Configure OSPF redistribution policies for direct routes
isis Configure OSPF redistribution policies for isis routes
rip Configure OSPF redistribution policies for RIP routes
static Configure OSPF redistribution policies for static routes
All the parameters listed under redistribute indicate sub-context commands.
You must use one of the available completions, and if necessary, use the command completion help
again to find the next completion.
Switch:1(config-ospf)#redistribute direct ?
enable Enable isis redistribute direct command
<cr>
When you see <cr> (Carriage Return/Enter Key) in the list with the additional choices, this means
that no additional parameters are required to execute the CLI command. However, the additional
choices listed could be peer commands or sub-context commands.
For example, the parameter listed under redistribute direct ? is a peer commands. You can
enter these peer commands on the same line as the root command, for example redistribute
direct enable. However, the <cr> indicates that you can also enter the redistribute
direct command only and this command does not require any additional parameters at this level.
Command completion
August 2019 Using CLI and EDM on Ethernet Routing Switch 3600 Series 13

CLI autocompletion
CLI autocompletion is a feature that you can use to automatically fill in the unique parts of a
command string rather than typing the entire command. Autcompletion makes the CLI experience
easier and prevents mistakes in spelling that force you to re-enter the command.
Autocompletion completes the token in the command as soon as it becomes unique.
The Tab key autocompletes the command without executing the command, and places the cursor
immediately after the last character. The Enter key autocompletes the command and executes it.
Example
To enable redistribution of OSPF direct routes,
Switch:1(config-ospf)#redistribute direct
When you use redistribute ?, you see four possible sub-context commands.
direct
isis
rip
static
If you type the following without pressing Enter:
Switch:1(config-ospf)#redistribute direct m
and press the Tab key, the system completes the command to the following point:
redistribute direct metric
Two possible completions exist. You can type -t, and then press Tab to finish the command:
Switch:1(config-ospf)#redistribute direct metric-type
default command operator
You can reset the modified configuration of a command to the default configuration by using the
default operator.
Use the ? command completion along with the default keyword in each configuration mode, to view
the list of commands that support the default operator. For more information, see Command
completion on page 13.
Example
Configure csnp-interval to its default value. The default value of csnp-interval is 10
seconds.
Switch:1>enable
Switch:1#configure terminal
Enter configuration commands, one per line. End with CNTL/Z.
Switch:1(config)#router isis
Switch:1(config-isis)#show isis
========================================================================================
ISIS General Info
Command Line Interface Fundamentals
August 2019 Using CLI and EDM on Ethernet Routing Switch 3600 Series 14

========================================================================================
AdminState : disabled
RouterType : Level 1
System ID : e45d.523c.6484
Max LSP Gen Interval : 900
Metric : wide
Overload-on-startup : 20
Overload : false
Csnp Interval : 200
PSNP Interval : 2
Rxmt LSP Interval : 5
spf-delay : 100
Router Name :
ip source-address :
ipv6 source-address :
ip tunnel source-address :
Tunnel vrf :
ip tunnel mtu :
Num of Interfaces : 1
Num of Area Addresses : 0
inband-mgmt-ip :
backbone : disabled
Dynamically Learned Area : 00.0000.0000
FAN Member : Yes
Switch:1(config-isis)#default csnp-interval
Switch:1(config-isis)#show isis
========================================================================================
ISIS General Info
========================================================================================
AdminState : disabled
RouterType : Level 1
System ID : e45d.523c.6484
Max LSP Gen Interval : 900
Metric : wide
Overload-on-startup : 20
Overload : false
Csnp Interval : 10
PSNP Interval : 2
Rxmt LSP Interval : 5
spf-delay : 100
Router Name :
ip source-address :
ipv6 source-address :
ip tunnel source-address :
Tunnel vrf :
ip tunnel mtu :
Num of Interfaces : 1
Num of Area Addresses : 0
inband-mgmt-ip :
backbone : disabled
Dynamically Learned Area : 00.0000.0000
FAN Member : Yes
Example
View the IP configuration commands for a VLAN interface that support the default operator.
Switch:1>enable
Switch:1#configure terminal
Enter configuration commands, one per line. End with CNTL/Z.
default command operator
August 2019 Using CLI and EDM on Ethernet Routing Switch 3600 Series 15

Switch:1(config)#interface vlan 1
Switch:1(config-if)#default ?
Default settings
ip Restore default L3 parameters on a VLAN
ipv6 Restore default IPv6 parameters on a VLAN
Switch:1(config-if)#default ip ?
Restore default L3 parameters on a vlan
arp-proxy Restore default Proxy ARP
dhcp-relay Disable DHCP relay on this vlan
directed-broadcast Restore default IP directed-broadcast
forward-protocol Configure to default broadcast forwarding
fwd-nh Restore default IP forwarding next-hop config settings
igmp Restore default per-vlan IGMP settings
ipsec ipsec configuration for an interface
ospf Restore default OSPF settings
pim Restore default per-vlan PIM settings
rip Restore default RIP settings
routing Disable L3 routing on a VLAN
spb-multicast Default spb-multicast commands
vrrp Restore default VR settings
Switch:1(config-ip)#default ip igmp ?
<cr>
no command operator
You can use the no operator in a command to negate a configuration. Based on the functionality of
the command, you can perform negations, such as disable, delete, remove, or reset to the default
configuration.
Use the ? command completion along with the no keyword to view the list of commands that support
the no operator in each configuration mode. For more information, see Command completion on
page 13.
Example
Negate the automatic virtual link that provides automatic dynamic backup link for OSPF traffic.
Switch:1>enable
Switch:1#configure terminal
Enter configuration commands, one per line. End with CNTL/Z.
Switch:1(config)#router ospf
Switch:1(config-router)#no auto-vlink
Example
Remove an IP address configuration from VLAN.
Switch:1>enable
Switch:1#configure terminal
Enter configuration commands, one per line. End with CNTL/Z.
Switch:1(config)#interface vlan 3
Switch:1(config-if)#no ip address 192.0.2.4
Command Line Interface Fundamentals
August 2019 Using CLI and EDM on Ethernet Routing Switch 3600 Series 16

Example
View the commands that can negate a configuration in RIP router configuration mode.
Switch:1>enable
Switch:1#configure terminal
Enter configuration commands, one per line. End with CNTL/Z.
Switch:1(config)#router rip
Switch:1(config-rip)#no ?
Negate a command or set its defaults
ipv6 Disable ipv6 configurations
network Disable rip on an ip network
redistribute To disable/delete redistribute golbally
Switch:1(config-rip)#no network ?
{A.B.C.D} Network ip address
LabSwitch:1(config-rip)#no network 192.0.2.4 ?
<cr>
GREP with CLI show command
You can use Global Regular Expression Print (GREP) with show commands to filter the output
based on match criterial.
Enter the show command followed by the pipe (|) character, followed by the GREP filter command.
The show command output contains only the lines that match the GREP filter pattern.
The following GREP filter commands are supported:
Filter function Description
count Counts the number of lines in the output of a command.
match Displays only the output lines which match the given pattern.
except Displays only the output lines which do not match the given pattern.
find Displays the output of a command starting from the first line which matches
the given pattern.
no-more Temporarily disables pagination for the output of an CLI command. When
the lines of output exceed the terminal length, the entire output of the
command is displayed and message does not appear to continue or quit.
head Limits the output of a command to the first few lines. If limit is not specified,
the first 10 lines appear.
tail Limits the output of a command to the last few lines. If a number is not
specified the last 10 lines are shown.
For more information about the functions, see GREP CLI show command filters on page 26.
CLI help
GREP with CLI show command
August 2019 Using CLI and EDM on Ethernet Routing Switch 3600 Series 17

CLI help is available at all levels.
CLI list
From the User EXEC mode, the CLI list command show cli list displays a detailed view of the
CLI commands. Additionally, the verbose command, show cli list verbose lists the CLI
syntax for each command.
Command list
To obtain a list of all commands available from a prompt, enter a question mark (?).
Command options
To obtain a list of all options for a command, at the prompt enter a portion of a command followed by
a space and a question mark (?).
Command names
To obtain a correct command name, at the prompt enter a portion of the command name, and then
press the Tab key. The system displays the first unambiguous match for your selection. For
example, when you enter down + Tab, the system displays download.
Command modes
To obtain a list of CLI command modes available, enter help modes.
Commands organized by mode
To obtain a list of CLI commands, organized by command mode, enter help commands. A short
explanation of each command is included.
Keystroke shortcuts
To make using CLI easier, use the keystroke shortcuts in the following table.
Key combination Function
Ctrl+A Start of line
Ctrl+B Back 1 character
Ctrl+C Abort command
Ctrl+D Delete the character indicated by the cursor
Ctrl+E End of line
Ctrl+F Forward 1 character
Ctrl+H Delete character left of cursor (Backspace key)
Tab Command or parameter completion
Ctrl+K and Ctrl+R Redisplay line
Ctrl+N or Down arrow Next history command
Ctrl+P or Up arrow Previous history command
Ctrl+T Transpose characters
Ctrl+U Delete entire line
Ctrl+W Delete word to left of cursor
Table continues…
Command Line Interface Fundamentals
August 2019 Using CLI and EDM on Ethernet Routing Switch 3600 Series 18

Key combination Function
Ctrl+X Delete all characters to left of cursor
Ctrl+z Exit Global Configuration mode to Privileged EXEC mode
?Context sensitive help
Esc+C and Exc+U Capitalize character at cursor
Esc+l Change character at cursor to lower case
Esc+B Move back 1 word
Esc+D Delete 1 word to the right
Esc+F Move 1 word forward
Getting EDM online help files for embedded EDM
Because help files are not included with the embedded EDM software files on the switch, you need
to download the help files to a TFTP destination and use CLI to configure a path from your switch to
the help files.
If you are using COM to manage your switch, help resides with COM and you do not need to use
these procedures.
Downloading help files
Use this procedure to download help files.
Before you begin
•An available TFTP server — ensure that the TFTP path differs from the path you use to
download switch software.
Important:
Do not install EDM help files on Flash.
Procedure
1. To obtain EDM help files for the embedded element manager, do one of the following;
• Go to https://extremeportal.force.com and locate the help file for the appropriate product.
• Select the help file from the software CD ROM contained in the Base Software License
Kit.
2. Download the help file to a TFTP server.
Getting EDM online help files for embedded EDM
August 2019 Using CLI and EDM on Ethernet Routing Switch 3600 Series 19

Command Line Interface Procedures
The following sections contain information about common Command Line Interface (CLI) tasks. You
can access CLI during runtime to manage the switch.
CLI Access Procedures
Before you begin
• Connect to the switch with a console cable, connected directly to the console port, or use
Telnet.
• To connect to the switch remotely, through Telnet, ensure that you enable remote access, and
that the switch IP address is valid.
• Use a terminal, or computer with a terminal emulator, as the CLI command station.
• If you use a console cable and console port, ensure that the terminal emulation program
conforms to settings listed in the following table.
Property Value
Baud Rate 9600 bps
Data Bits 8
Stop Bits 1
Parity None
Flow Control None
Terminal Protocol VT100 and VT100/ANSI
Opening a CLI session
Procedure
1. Connect to the switch.
2. Enter the password, if applicable.
3. At the CLI Banner Screen, enter CTRL+Y.
4. To access CLI, from the main menu, press c or scroll to Command Line Interface.
5. Press Enter.
Configuring the path to the help files using CLI
Use this procedure to configure the path to the help files.
Procedure
1. Enter Global Configuration mode:
enable
Command Line Interface Fundamentals
August 2019 Using CLI and EDM on Ethernet Routing Switch 3600 Series 20