Extron electronics Extron P/2 DA2xi User manual

User’s Guide
P/2 DA2xi and P/2 DA2xi MT • InstallationP/2 DA2xi and P/2 DA2xi MT • Installation
Introduction
32
© 2005 Extron Electronics. All rights reserved.
Extron Electronics, USA
1230 South Lewis Street
Anaheim, CA 92805
USA
714.491.1500
Fax [phone]
Extron Electronics, Europe
Beeldschermweg 6C
3821 AH Amersfoort
The Netherlands
+31.33.453.4040
Fax [phone]
Extron Electronics, Asia
135 Joo Seng Road, #04-01
PM Industrial Building
Singapore 368363
+65.6383.4400
Fax [phone]
Extron Electronics, Japan
Kyodo Building
16 Ichibancho
Chiyoda-ku, Tokyo 102-0082 Japan
+81.3.3511.7655
Fax [phone]
www.extron.com
The Extron P/2 DA2xi and the P/2 DA2xi MT are distribution
amplifiers that accept video input from a VGA, XGA, or UXGA
compatible PC and distribute the signal to separately buffered
outputs. Each output can be extended with Extron VGA MHR
cables from 6' to 250' in length. The MT model also has audio
input and output.
Features
• Power/Signal LED — Green LED = power + signal.
Amber LED = power but no signal. Off = no power.
• Gain/Peak DIP switch — Use this feature to compensate for
longer cable runs.
• Out Imp DIP switch — Changes the output impedance to be
compatible with all projectors.
• Cable retention chain — The input cable can be secured to the
unit (either model) with the supplied chain (attached to the
right standoff nut of the input VGA connector) to prevent the
cable from becoming lost or misplaced.
MONITOR
AUDIO
INPUT
Installation
The P/2 DA2xi and P/2 DA2xi MT can be mounted on a rack
shelf, under a desk or tabletop, or on a projector bracket.
Rack mounting
For optional rack mounting, mount the P/2 DA2xi or
P/2 DA2xi MT on a 19", 1U RSF 123 VersaTools®rack shelf kit
(part #60-190-20) or a standard RSU 129 1U universal rack shelf
kit (part #60-190-01) as shown in the next figure.
Only products in the VersaTools line can be mounted to a
VersaTools rack shelf.
1. Remove the rubber feet (if installed) and mount the unit on the
rack shelf, using two screws in opposite (diagonal) corners.
2. Install blank panel(s) or other unit(s) to the rack shelf.
3. Insert the shelf into the rack, and secure the shelf to the rack
using the supplied machine screws.
Use 2 mounting holes on
opposite corners.
VersaTools Rack Shelf
1/4 Rack Width False Front
Face Plate
Universal Rack Shelf
DISTRIBUTIONAMPLIFIER
DISTRIBUTIONAMPLIFIERDISTRIBUTIONAMPLIFIER
DISTRIBUTIONAMPLIFIER DISTRIBUTIONAMPLIFIER
DISTRIBUTIONAMPLIFIER
MDASERIES
DISTRIBUTIONAMPLIFIER
Mounting the P/2 DA2xi or P/2 DA2xi MT on a rack shelf
Furniture or projector mounting
For optional furniture or projector mounting, mount the unit
using the mounting kit (part #70-077-01 for furniture [optional
with the P/2 DA2xi, standard with P/2 DA2xi MT] or #70-077-04
for projector [optional with both units]) as follows:
1. Attach the mounting brackets to the distribution amplifier
with the provided machine screws, as shown below.
Ceiling
Digital Projector
Projector
Mounting
Bracket
Mounting
Bolt
INPUTMONITOR
P/2DA2xi
OUTPUT
GAIN/
PEAK
1
ON
2
SPARE
EXTPOWER(see manual)
5V
0.1AMAX
Projector and furniture mounting
2. If feet were previously installed on the bottom of the unit,
remove them.
3.For furniture mounting, hold the unit with the attached
brackets against the underside of the table or other
furniture. Mark the location of the screw holes of the
bracket on the mounting surface.
For projector mounting, secure the unit to a projector
mount or other surface by inserting the mounting bolt
through the bracket’s slotted hole.
General
External power supply .................. 100 VAC to 240 VAC, 50/60 Hz, external,
autoswitchable; to 12 VDC, 1 A, regulated
Power input requirements ............ 12 VDC
P/2 DA2x ............................ 0.1 A
P/2 DA2xi MT ................... 0.2 A
Temperature/humidity ................ Storage: -40 to +158 °F (-40 to +70 °C) /
10% to 90%, noncondensing
Operating: +32 to +122 °F (0 to +50 °C) /
10% to 90%, noncondensing
Rack mount ..................................... Yes, with optional 1U rack shelf, part
#60-190-01 or 60-604-01; or VersaTools®rack
shelf, part #60-190-20 or 60-604-20; also
under-furniture mountable with optional
brackets #70-077-01; or projector mountable
with bracket kit #70-077-04 (optional for
P/2 DA2xi, standard for P/2 DA2xi MT)
Enclosure type ................................ Metal
Enclosure dimensions ................... 1.0" H x 4.3" W x 3.0" D (quarter rack wide)
2.5 cm H x 10.9 cm W x 7.6 cm D
(Depth excludes connectors.)
Product weight ............................... 0.5 lbs (0.3 kg)
Shipping weight ............................. 3 lbs (2 kg)
Vibration .......................................... ISTA 1A in carton
(International Safe Transit Association)
Listings ............................................. UL, CUL
Compliances .................................... CE, FCC Class A, VCCI, AS/NZS, ICES
MTBF ................................................ 30,000 hours
Warranty .......................................... 3 years parts and labor
All nominal levels are at ±10%.
Specifications are subject to change without notice.
Distribution Amplifiers
68-713-01 Rev. D
08 05
P/2 DA2xi, P/2 DA2xi MT
FCC Class A Notice
Note: This equipment has been tested and found to comply with the limits for a
Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed
to provide reasonable protection against harmful interference when the equipment is
operated in a commercial environment. This equipment generates, uses and can
radiate radio frequency energy and, if not installed and used in accordance with the
instruction manual, may cause harmful interference to radio communications.
Operation of this equipment in a residential area is likely to cause harmful
interference, in which case the user will be required to correct the interference at his
own expense.
Note: This unit was tested with shielded cables on the peripheral devices. Shielded
cables must be used with the unit to ensure compliance.
im Vertrieb von
CAMBOARD Electronics
www.camboard.de
Tel. [phone]
Fax [phone]
[email protected]

User’s Guide
P/2 DA2xi and P/2 DA2xi MT • InstallationP/2 DA2xi and P/2 DA2xi MT • Installation
Introduction
32
© 2005 Extron Electronics. All rights reserved.
Extron Electronics, USA
1230 South Lewis Street
Anaheim, CA 92805
USA
714.491.1500
Fax [phone]
Extron Electronics, Europe
Beeldschermweg 6C
3821 AH Amersfoort
The Netherlands
+31.33.453.4040
Fax [phone]
Extron Electronics, Asia
135 Joo Seng Road, #04-01
PM Industrial Building
Singapore 368363
+65.6383.4400
Fax [phone]
Extron Electronics, Japan
Kyodo Building
16 Ichibancho
Chiyoda-ku, Tokyo 102-0082 Japan
+81.3.3511.7655
Fax [phone]
www.extron.com
The Extron P/2 DA2xi and the P/2 DA2xi MT are distribution
amplifiers that accept video input from a VGA, XGA, or UXGA
compatible PC and distribute the signal to separately buffered
outputs. Each output can be extended with Extron VGA MHR
cables from 6' to 250' in length. The MT model also has audio
input and output.
Features
• Power/Signal LED — Green LED = power + signal.
Amber LED = power but no signal. Off = no power.
• Gain/Peak DIP switch — Use this feature to compensate for
longer cable runs.
• Out Imp DIP switch — Changes the output impedance to be
compatible with all projectors.
• Cable retention chain — The input cable can be secured to the
unit (either model) with the supplied chain (attached to the
right standoff nut of the input VGA connector) to prevent the
cable from becoming lost or misplaced.
MONITOR
AUDIO
INPUT
Installation
The P/2 DA2xi and P/2 DA2xi MT can be mounted on a rack
shelf, under a desk or tabletop, or on a projector bracket.
Rack mounting
For optional rack mounting, mount the P/2 DA2xi or
P/2 DA2xi MT on a 19", 1U RSF 123 VersaTools®rack shelf kit
(part #60-190-20) or a standard RSU 129 1U universal rack shelf
kit (part #60-190-01) as shown in the next figure.
Only products in the VersaTools line can be mounted to a
VersaTools rack shelf.
1. Remove the rubber feet (if installed) and mount the unit on the
rack shelf, using two screws in opposite (diagonal) corners.
2. Install blank panel(s) or other unit(s) to the rack shelf.
3. Insert the shelf into the rack, and secure the shelf to the rack
using the supplied machine screws.
Use 2 mounting holes on
opposite corners.
VersaTools Rack Shelf
1/4 Rack Width False Front
Face Plate
Universal Rack Shelf
DISTRIBUTIONAMPLIFIER
DISTRIBUTIONAMPLIFIERDISTRIBUTIONAMPLIFIER
DISTRIBUTIONAMPLIFIER DISTRIBUTIONAMPLIFIER
DISTRIBUTIONAMPLIFIER
MDASERIES
DISTRIBUTIONAMPLIFIER
Mounting the P/2 DA2xi or P/2 DA2xi MT on a rack shelf
Furniture or projector mounting
For optional furniture or projector mounting, mount the unit
using the mounting kit (part #70-077-01 for furniture [optional
with the P/2 DA2xi, standard with P/2 DA2xi MT] or #70-077-04
for projector [optional with both units]) as follows:
1. Attach the mounting brackets to the distribution amplifier
with the provided machine screws, as shown below.
Ceiling
Digital Projector
Projector
Mounting
Bracket
Mounting
Bolt
INPUTMONITOR
P/2DA2xi
OUTPUT
GAIN/
PEAK
1
ON
2
SPARE
EXTPOWER(see manual)
5V
0.1AMAX
Projector and furniture mounting
2. If feet were previously installed on the bottom of the unit,
remove them.
3.For furniture mounting, hold the unit with the attached
brackets against the underside of the table or other
furniture. Mark the location of the screw holes of the
bracket on the mounting surface.
For projector mounting, secure the unit to a projector
mount or other surface by inserting the mounting bolt
through the bracket’s slotted hole.
General
External power supply .................. 100 VAC to 240 VAC, 50/60 Hz, external,
autoswitchable; to 12 VDC, 1 A, regulated
Power input requirements ............ 12 VDC
P/2 DA2x ............................ 0.1 A
P/2 DA2xi MT ................... 0.2 A
Temperature/humidity ................ Storage: -40 to +158 °F (-40 to +70 °C) /
10% to 90%, noncondensing
Operating: +32 to +122 °F (0 to +50 °C) /
10% to 90%, noncondensing
Rack mount ..................................... Yes, with optional 1U rack shelf, part
#60-190-01 or 60-604-01; or VersaTools®rack
shelf, part #60-190-20 or 60-604-20; also
under-furniture mountable with optional
brackets #70-077-01; or projector mountable
with bracket kit #70-077-04 (optional for
P/2 DA2xi, standard for P/2 DA2xi MT)
Enclosure type ................................ Metal
Enclosure dimensions ................... 1.0" H x 4.3" W x 3.0" D (quarter rack wide)
2.5 cm H x 10.9 cm W x 7.6 cm D
(Depth excludes connectors.)
Product weight ............................... 0.5 lbs (0.3 kg)
Shipping weight ............................. 3 lbs (2 kg)
Vibration .......................................... ISTA 1A in carton
(International Safe Transit Association)
Listings ............................................. UL, CUL
Compliances .................................... CE, FCC Class A, VCCI, AS/NZS, ICES
MTBF ................................................ 30,000 hours
Warranty .......................................... 3 years parts and labor
All nominal levels are at ±10%.
Specifications are subject to change without notice.
Distribution Amplifiers
68-713-01 Rev. D
08 05
P/2 DA2xi, P/2 DA2xi MT
FCC Class A Notice
Note: This equipment has been tested and found to comply with the limits for a
Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed
to provide reasonable protection against harmful interference when the equipment is
operated in a commercial environment. This equipment generates, uses and can
radiate radio frequency energy and, if not installed and used in accordance with the
instruction manual, may cause harmful interference to radio communications.
Operation of this equipment in a residential area is likely to cause harmful
interference, in which case the user will be required to correct the interference at his
own expense.
Note: This unit was tested with shielded cables on the peripheral devices. Shielded
cables must be used with the unit to ensure compliance.
im Vertrieb von
CAMBOARD Electronics
www.camboard.de
Tel. [phone]
Fax [phone]
[email protected]

P/2 DA2xi and P/2 DA2xi MT • ConnectionsP/2 DA2xi and P/2 DA2xi MT • Connections
Installation
54
P/2 DA2xi and P/2 DA2xi MT • Specifications
P/2 DA2xi and P/2 DA2xi MT • Specifications
Specifications
76
4.For furniture mounting, drill 3/32" (2 mm) diameter pilot
holes, 1/4" (6.3 mm) deep in the mounting surface at the
marked screw locations.
5.For furniture mounting, insert #8 wood screws into the four
pilot holes. Tighten each screw into the mounting surface
until just less than 1/4" of the screw head protrudes.
6.For furniture mounting, align the mounting screws with
the slots in the brackets and place the unit against the
surface, with the screws through the bracket slots.
7.For furniture mounting, slide the receiver slightly forward or
back, then tighten all four screws to secure the unit in place.
Connections, Indicators, and Controls
INPUT MONITOR
P/2 DA2xi
OUTPUT
1
ON
2
EXT POWER (see manual)
5V
0.1A MAX
GAIN/PEAK
OUT IMP
AUDIO
INPUT MONITOR
LR
P/2 DA2xi MT
OUTPUT
1
ON
2
EXT POWER (see manual)
5V
0.2A MAX
GAIN/PEAK
OUT IMP
7
6
1
263
56
7
6
1
23
74
65 6
6
7
68
4
6
9
6
Front and rear panels
1
Power/Signal indicator LED — When lit green, this LED
indicates that the distribution amplifier is receiving both
power and a computer signal. When lit amber, it indicates
that the distribution amplifier is receiving power but no
computer signal.
2
Video Input connector — Connect a computer’s VGA -
UXGA output to this connector.
3
Monitor connector — Connect a local monitor to this
connector.
4
Power connector — Plug the external 12 V power supply,
only when needed (see Power/Signal indicator LED above),
into this 2-pole captive screw connector. The included
power supply is shipped with a plug installed. If you need
to cut the power cord to a different length and reinstall the
plug, refer to the figure below and the following notes.
+
–
Power supply output cord
5 mm
End view of power
supply output cord
Captive screw
connector
AA
SECTION A–A
12 VDC
Power
Power connector wiring
CAUTION
When you connect the power supply, voltage polarity
is extremely important. Applying power with
incorrect voltage polarity could damage the power
supply and the amplifier. Identify the power cord
negative lead by the ridges on the side of the cord.
Do not tin the stripped power supply leads before
installing the captive screw connector. Tinned wires are
not as secure in the connectors and could pull out. Strip
the power cord jacket 5 mm from the end.
The two power cord wires must be kept separate while
the power supply is plugged in. Remove power before
continuing.
To verify the polarity before connection, plug in the power
supply with no load and check the output with a voltmeter.
5
2-bank DIP switches —These switches affect only the
video output (
6
), not the “monitor” output (
3
). The
Gain/Peak DIP switch should be on (up) when output
cable is over 100' (30.5 m). The Out Imp DIP switch
changes output impedance. If all connections and
operations are correct, yet the output device has no picture,
switch to the other position.
6
Video output connector — Connect the video output
device (projector, display panel, or monitor) to this
connector.
7
Audio input connector (MT model only) — Plug a
3.5 mm, mini plug audio cable from the computer’s sound
card into this jack.
8
Audio output connector (MT model only) — Wire a
3.5 mm, 5-pole, captive screw audio connector as shown
below, and plug it into this connector. Connect the other
end of the cable to an audio output device or recorder.
Unbalanced Output
Tip
See Caution.
Sleeve(s)
Tip
See Caution.
Balanced Output
Tip
Ring
Sleeve(s)
Tip
Ring
LR
AUDIO AUDIO
LR
CAUTION
Connect the sleeve to ground (Gnd). Connecting the
sleeve to a negative (-) terminal will damage the audio
output circuits.
9
Local monitor cable assembly — Use this cable assembly
to connect the local monitor (video) and speaker (audio) to
the unit. The chain is used to attach the cable to the unit, to
prevent the cable from being lost or misplaced.
Specifications
Video
Gain .................................................. Selectable: 0.7 V (unity), or 0.75 V
Peaking ............................................ Selectable: 0 dB or 6 dB @100 MHz
Bandwidth ....................................... 350 MHz (-3 dB)
Video input
Number/signal type ...................... 1 VGA-UXGA RGBHV, RGBS, RGsB,
RsGsBs input
Connectors ...................................... (1) 15-pin HD female
Nominal level ................................. 0.7 Vp-p for RGB
Minimum/maximum levels ........ Analog, 0.3 V to 1.5 Vp-p with no offset at
unity gain
Impedance ....................................... 75 ohms
Horizontal frequency .................... 15 kHz to 135 kHz
Vertical frequency .......................... 30 Hz to 170 Hz
Return loss ....................................... <-38 dB @ 5 MHz
DC offset (max. allowable) ........... 1.0 V
Input coupling ................................ DC
Video output
Number/signal type ...................... 1 VGA-UXGA RGBHV, RGBS, RGsB,
RsGsBs output; 1 VGA-UXGA RGBHV,
RGBS, RGsB, RsGsBs local monitor loop-
through (i.d. bits are passed through)
Connectors ...................................... (2) 15-pin HD female
Nominal level ................................. 0.7 Vp-p for RGB at unity gain
Minimum/maximum levels ........ Analog, 0.3 V to 1.5 Vp-p (follows input)
Impedance ....................................... 75 ohms
Return loss ....................................... <-40 dB @ 5 MHz
DC offset .......................................... ±5 mV with input at 0 offset
Sync
Input type ........................................ RGBHV, RGBS, RGsB, RsGsBs
Output type ..................................... RGBHV, RGBS, RGsB, RsGsBs
Input level ....................................... 1.5 V to 5.0 Vp-p
Output level .................................... TTL, 4 V to 5 Vp-p, unterminated
Input impedance ............................ 510 ohms
Output impedance ......................... 75 ohms or 55 ohms, switchable (Output
impedance resistors are 50 and 30 ohms.)
Max input voltage .......................... 5.0 Vp-p
Max. propagation delay ................ 60 ns
Max. rise/fall time ......................... 4 ns
Polarity ............................................. Positive or negative (follows input)
Audio — P/2 DA2xi MT only
Gain .................................................. Unbalanced output: 0 dB; balanced output:
+6 dB
Frequency response ....................... 20 Hz to 20 kHz, +0.05 dB, -0.1 dB
THD + Noise ................................... 0.03% @ 1 kHz at nominal level
S/N .................................................. >90 dB (balanced) at maximum output
Crosstalk .......................................... <-80 dB @ 1 kHz, fully loaded
Stereo channel separation ............. >80 dB @ 1 kHz, >60 dB @ 20 kHz
CMRR ............................................... >67 dB @ 20 Hz to 20 kHz
Audio input — P/2 DA2xi MT only
Number/signal type ...................... 1 stereo, unbalanced
Connectors ...................................... (1) 3.5 mm stereo jack, female; tip (L), ring
(R), sleeve (GND)
Impedance ....................................... >18k ohms unbalanced, DC coupled
Nominal level ................................. -10 dBV (316 mV)
Maximum level............................... >+10 dBV (3.16 V) (unbalanced) at 1%
THD+N
0 dBu = 0.775 Vrms, 0 dBV = 1 Vrms, 0 dBV 2 dBu
Audio output — P/2 DA2xi MT only
Number/signal type ...................... 1 stereo, balanced/unbalanced
Connectors ...................................... (1) 3.5 mm captive screw connector, 5 pole
Impedance ....................................... 50 ohms unbalanced, 100 ohms balanced
Gain error ........................................ ±0.1 dB channel to channel
Nominal level ................................. -2 dBu (632 mV) balanced output
-10 dBV (316 mV) unbalanced output
Maximum level (Hi-Z) .................. >+15 dBu (4.36 V), balanced at 1% THD+N,
with external power supply
Maximum level (600 ohms) .......... >+9 dBm (2.18 V), balanced at 1% THD+N,
with external power supply
im Vertrieb von
CAMBOARD Electronics
www.camboard.de
Tel. [phone]
Fax [phone]
[email protected]

P/2 DA2xi and P/2 DA2xi MT • ConnectionsP/2 DA2xi and P/2 DA2xi MT • Connections
Installation
54
P/2 DA2xi and P/2 DA2xi MT • Specifications
P/2 DA2xi and P/2 DA2xi MT • Specifications
Specifications
76
4.For furniture mounting, drill 3/32" (2 mm) diameter pilot
holes, 1/4" (6.3 mm) deep in the mounting surface at the
marked screw locations.
5.For furniture mounting, insert #8 wood screws into the four
pilot holes. Tighten each screw into the mounting surface
until just less than 1/4" of the screw head protrudes.
6.For furniture mounting, align the mounting screws with
the slots in the brackets and place the unit against the
surface, with the screws through the bracket slots.
7.For furniture mounting, slide the receiver slightly forward or
back, then tighten all four screws to secure the unit in place.
Connections, Indicators, and Controls
INPUT MONITOR
P/2 DA2xi
OUTPUT
1
ON
2
EXT POWER (see manual)
5V
0.1A MAX
GAIN/PEAK
OUT IMP
AUDIO
INPUT MONITOR
LR
P/2 DA2xi MT
OUTPUT
1
ON
2
EXT POWER (see manual)
5V
0.2A MAX
GAIN/PEAK
OUT IMP
7
6
1
263
56
7
6
1
23
74
65 6
6
7
68
4
6
9
6
Front and rear panels
1
Power/Signal indicator LED — When lit green, this LED
indicates that the distribution amplifier is receiving both
power and a computer signal. When lit amber, it indicates
that the distribution amplifier is receiving power but no
computer signal.
2
Video Input connector — Connect a computer’s VGA -
UXGA output to this connector.
3
Monitor connector — Connect a local monitor to this
connector.
4
Power connector — Plug the external 12 V power supply,
only when needed (see Power/Signal indicator LED above),
into this 2-pole captive screw connector. The included
power supply is shipped with a plug installed. If you need
to cut the power cord to a different length and reinstall the
plug, refer to the figure below and the following notes.
+
–
Power supply output cord
5 mm
End view of power
supply output cord
Captive screw
connector
AA
SECTION A–A
12 VDC
Power
Power connector wiring
CAUTION
When you connect the power supply, voltage polarity
is extremely important. Applying power with
incorrect voltage polarity could damage the power
supply and the amplifier. Identify the power cord
negative lead by the ridges on the side of the cord.
Do not tin the stripped power supply leads before
installing the captive screw connector. Tinned wires are
not as secure in the connectors and could pull out. Strip
the power cord jacket 5 mm from the end.
The two power cord wires must be kept separate while
the power supply is plugged in. Remove power before
continuing.
To verify the polarity before connection, plug in the power
supply with no load and check the output with a voltmeter.
5
2-bank DIP switches —These switches affect only the
video output (
6
), not the “monitor” output (
3
). The
Gain/Peak DIP switch should be on (up) when output
cable is over 100' (30.5 m). The Out Imp DIP switch
changes output impedance. If all connections and
operations are correct, yet the output device has no picture,
switch to the other position.
6
Video output connector — Connect the video output
device (projector, display panel, or monitor) to this
connector.
7
Audio input connector (MT model only) — Plug a
3.5 mm, mini plug audio cable from the computer’s sound
card into this jack.
8
Audio output connector (MT model only) — Wire a
3.5 mm, 5-pole, captive screw audio connector as shown
below, and plug it into this connector. Connect the other
end of the cable to an audio output device or recorder.
Unbalanced Output
Tip
See Caution.
Sleeve(s)
Tip
See Caution.
Balanced Output
Tip
Ring
Sleeve(s)
Tip
Ring
LR
AUDIO AUDIO
LR
CAUTION
Connect the sleeve to ground (Gnd). Connecting the
sleeve to a negative (-) terminal will damage the audio
output circuits.
9
Local monitor cable assembly — Use this cable assembly
to connect the local monitor (video) and speaker (audio) to
the unit. The chain is used to attach the cable to the unit, to
prevent the cable from being lost or misplaced.
Specifications
Video
Gain .................................................. Selectable: 0.7 V (unity), or 0.75 V
Peaking ............................................ Selectable: 0 dB or 6 dB @100 MHz
Bandwidth ....................................... 350 MHz (-3 dB)
Video input
Number/signal type ...................... 1 VGA-UXGA RGBHV, RGBS, RGsB,
RsGsBs input
Connectors ...................................... (1) 15-pin HD female
Nominal level ................................. 0.7 Vp-p for RGB
Minimum/maximum levels ........ Analog, 0.3 V to 1.5 Vp-p with no offset at
unity gain
Impedance ....................................... 75 ohms
Horizontal frequency .................... 15 kHz to 135 kHz
Vertical frequency .......................... 30 Hz to 170 Hz
Return loss ....................................... <-38 dB @ 5 MHz
DC offset (max. allowable) ........... 1.0 V
Input coupling ................................ DC
Video output
Number/signal type ...................... 1 VGA-UXGA RGBHV, RGBS, RGsB,
RsGsBs output; 1 VGA-UXGA RGBHV,
RGBS, RGsB, RsGsBs local monitor loop-
through (i.d. bits are passed through)
Connectors ...................................... (2) 15-pin HD female
Nominal level ................................. 0.7 Vp-p for RGB at unity gain
Minimum/maximum levels ........ Analog, 0.3 V to 1.5 Vp-p (follows input)
Impedance ....................................... 75 ohms
Return loss ....................................... <-40 dB @ 5 MHz
DC offset .......................................... ±5 mV with input at 0 offset
Sync
Input type ........................................ RGBHV, RGBS, RGsB, RsGsBs
Output type ..................................... RGBHV, RGBS, RGsB, RsGsBs
Input level ....................................... 1.5 V to 5.0 Vp-p
Output level .................................... TTL, 4 V to 5 Vp-p, unterminated
Input impedance ............................ 510 ohms
Output impedance ......................... 75 ohms or 55 ohms, switchable (Output
impedance resistors are 50 and 30 ohms.)
Max input voltage .......................... 5.0 Vp-p
Max. propagation delay ................ 60 ns
Max. rise/fall time ......................... 4 ns
Polarity ............................................. Positive or negative (follows input)
Audio — P/2 DA2xi MT only
Gain .................................................. Unbalanced output: 0 dB; balanced output:
+6 dB
Frequency response ....................... 20 Hz to 20 kHz, +0.05 dB, -0.1 dB
THD + Noise ................................... 0.03% @ 1 kHz at nominal level
S/N .................................................. >90 dB (balanced) at maximum output
Crosstalk .......................................... <-80 dB @ 1 kHz, fully loaded
Stereo channel separation ............. >80 dB @ 1 kHz, >60 dB @ 20 kHz
CMRR ............................................... >67 dB @ 20 Hz to 20 kHz
Audio input — P/2 DA2xi MT only
Number/signal type ...................... 1 stereo, unbalanced
Connectors ...................................... (1) 3.5 mm stereo jack, female; tip (L), ring
(R), sleeve (GND)
Impedance ....................................... >18k ohms unbalanced, DC coupled
Nominal level ................................. -10 dBV (316 mV)
Maximum level............................... >+10 dBV (3.16 V) (unbalanced) at 1%
THD+N
0 dBu = 0.775 Vrms, 0 dBV = 1 Vrms, 0 dBV 2 dBu
Audio output — P/2 DA2xi MT only
Number/signal type ...................... 1 stereo, balanced/unbalanced
Connectors ...................................... (1) 3.5 mm captive screw connector, 5 pole
Impedance ....................................... 50 ohms unbalanced, 100 ohms balanced
Gain error ........................................ ±0.1 dB channel to channel
Nominal level ................................. -2 dBu (632 mV) balanced output
-10 dBV (316 mV) unbalanced output
Maximum level (Hi-Z) .................. >+15 dBu (4.36 V), balanced at 1% THD+N,
with external power supply
Maximum level (600 ohms) .......... >+9 dBm (2.18 V), balanced at 1% THD+N,
with external power supply
im Vertrieb von
CAMBOARD Electronics
www.camboard.de
Tel. [phone]
Fax [phone]
[email protected]