Extron electronics IPL Pro Series User manual

1
IMPORTANT:
Go to www.extron.com for the complete
user guide, installation instructions, and
specifications bef
ore connecting the
pr
oduct to the po
wer source.
IPL Pro Series • Setup Guide
The Extron IPL Pro Series IP Link®Pro Control Processors integrate Ethernet connection into AV systems to allow users to
remotely control, monitor, and troubleshoot AV equipment, including display
devices and switchers. These control processors include an embedded web
server and support for power over Ethernet
(PoE). Depending on the model, an IPLPro
control processor can include multiple
bidirectional serial ports, relays, IR/serial ports,
or contact input ports for use in applications
that require control and monitoring of multiple
devices within a large-scale AV system.
This guide provides instructions for an experienced installer to install an IPLPro
Series control processor and to create a basic configuration. Use Extron
Toolbelt software to discover and manage the IPLPro control processor and
other Extron control products. Configure the control processor using Extron
Global Configurator®software running in GlobalConfigurator Professional
(GCProfessional) or GlobalConfigurator Plus (GC Plus) mode, or program the
control processor using Extron Global Scripter®(GS). The IPL integrates seamlessly
with Extron GlobalViewer®Enterprise (GVE) software and Extron Control apps for
remote control applications. These control processors support multiple TouchLink®Pro touchpanel interfaces over a standard
Ethernet network. Global Configurator and other useful software applications are available at www.extron.com.
Setup Checklist: How to Proceed With Installation
Get Ready
Familiarize yourself with the features of the control processor (see Front Panel Features on page4 and Rear Panel
Features) and of any TouchLinkPro touchpanels that will be part of the system.
Download and install the latest version of the following:
• Toolbelt software — for discovering the control processor and other control products on the network, for managing
core settings, and for upgrading firmware when needed.
• Global Configurator (GC) software — for configuring the control system.
• Global Scripter software — for programming the control processor (as an alternative to GC)
• GUI Designer software — for designing layouts for Extron TouchLinkPro touchpanels and third party touch interfaces
• IPLinkPro device drivers — for use with GC, to make control of AV devices possible
• IR Learner Pro software — for use with models (IPL Pro IRS8) that have IR receiver ports. Use this to create your own
IR drivers using the remote control of an AV device, if drivers are not already available from Extron
All are available from www.extron.com (see Locating Software, Firmware, and Driver Files on the Extron Website on
page9).
Obtain network information for the unit from the network administrator. You will need the following details for each IPLinkPro
device:
DHCP setting (on or off) Subnet mask Username
Device (IPL Pro, TouchlinkPro, IPCPPro) IP address Gateway IP address Passwords
Write down the MAC address of each IPLinkPro device to be used.
Obtain model names and setup information for devices the IPL will control.
Each control processor comes with a factory-installed Secure Sockets Layer (SSL) security certificate. If you intend to install
a different SSL certificate, contact your IT department to obtain the certificate or for instructions on how to obtain one. See
“Secure Sockets Layer (SSL) Certificates” in the IPLProSeries User Guide for requirements and guidelines regarding SSL
certificates.

2
IPL Pro Series • Setup Guide (Continued)
Mount and Cable All Devices
Mount the unit to a rack or furniture (see Mounting on page3).
Cable devices to the control processor (see Cabling and Features on page 5).
Connect power cords and power on all the devices.
Set up the Control Processor and Touchpanels for Network Communication
Connect the PC that you will use for setup, the control processor, and touchpanels to the same Ethernet subnetwork.
For control processor LAN connections, see Control - LAN (Ethernet) on page6.
Start Toolbelt and use it to set the IP address, subnet, gateway IP address, DHCP status, and related settings (see the
flowchart in Network Communication Setup on the next page).
NOTE: When setting up DHCP during network configuration or if using a host name instead of an IP address, the user
must enter a qualified host name (Username.HostName.Domain). For example: somename.extron.com.
Configure or Program the Control Processor and Touchpanels
The most basic steps are outlined below in the recommended order.
NOTE: See the Toolbelt Help File, Global Configurator Help File, Global Scripter Help File, and GUI Designer Help File as
needed for step-by-step instructions and detailed information. The help file for GC includes an introduction to the software
and how to start a project and configuration.
If TouchLinkPro touchpanels are part of the system, start and use GUI Designer to design, save, and build the graphical
user interface (GUI) layout for the touchpanels.
Using GC, create a new GCPlus or GCProfessional project and configure the control processor and other IPLinkPro
devices. The configuration tells the control processor:
• how its ports function • what to monitor
• how to control other products • when to do things
• which touchpanels to interact with • whom to notify, how, and under what circumstances
Configure ports on the control processor.
• Select device drivers and link them to each serial, IR/serial, or Ethernet port.
• Select settings (serial protocol, relay behavior, contact input behavior) as needed.
Set up monitors, schedules, macros, and local variables.
Add touchpanels and set them up:
• Upload the GUI configuration for each touchpanel to the GC project using Global Configurator.
• Assign any appropriate functions, monitors, or schedules to the touchpanels and their buttons.
If not using GC Professional or GC Plus, use Global Scripter to program the control system as desired.
Program ports on the control processor.
• Program each serial, IR/serial, or Ethernet port.
• Program relay behavior or contact input settings as needed.
Add touchpanels and set them up:
• Upload the GUI configuration for the touchpanels.
• Program the touchpanel buttons.
Save and build the project.
Upload the system configuration to the control processor.
Test and Troubleshoot
Test the system (see the IPLProUser Guide for an outline of the system testing procedure).
Make adjustments to wiring or configuration as needed.
Rev. E: Updated
wording regarding
adding touchpanel
GUIs.

3
Network Communication Setup
Network setup is essential prior to configuration. Use the following flowchart as a guide to setting up the control processor for
network use.
Open the Toolbelt software from within
Global Congurator (GC Professional or GC Plus mode)
or as the stand-alone application.
Start Device Discovery.
Toolbelt displays a list of all Extron control devices
connected to the network.
Using the MAC address, locate the desired device
in the list and select it.
Network Communication Setup
Connect the control processor
and PC to the same network.
Apply power to all devices.
Use the Set IP feature in Toolbelt or
use the Toolbelt Manage > Network Settings tab
feature to enter the IP address, subnet address,
and gateway, then congure other network settings
as needed.
Figure 1. Network Setup
Mounting
Securely mount the control processor and other devices and attach cables using the wiring section (Cabling and Features on
page5) as a wiring guide. Optional 1U rack shelves and furniture mounting bracket kits are available for use with the control
processor. Read and follow the instructions and UL guidelines that come with the rack shelf or mounting kit for installation
procedures.
See the product-specific page at www.extron.com for a list of compatible accessories for mounting your control processor.

4
IPL Pro Series • Setup Guide (Continued)
Front Panel Features
R
1000
LINK
ACT
COM
312 645
RTS
CTS
Tx
Rx
R
1000
LINK
ACT
IPL PRO S3
312
RTS
CTS
Tx
Rx
COM
COM
RTS
CTS
Tx
Rx
R
IPL PRO S1
IPL PRO S6
R
1000
LINK
ACT
3
4
1
2
3
4
1
2
7
8
5
6
7
8
5
6
RELAYS
INPUT
R
1000
LINK
ACT
IR
IR/SERIAL
6
5
7
8
2
1
3
4
IPL PRO CR88
IPL PRO IRS8
NOTE: Numbers adjacent to LEDs
correspond to the like-numbered
rear panel ports.
COM (Serial)
LEDs
COM (Serial)
LEDs
Reset
Button
(recessed)
Reset
Button
(recessed)
Power
LED
Power
LED
Power
LED
LAN/
Network
LEDs
Reset
Button
(recessed)
Power
LED
Power
LED
LAN/
Networ
k
LEDs
IR/Serial
LEDs
Contact Input
LEDs
Relay
LEDs
IR Learning
Receiver
Figure 2. IPL Pro Series Front Panel Features
Rear Panel Features
POWER
12V
0.2A MAX
POWER
12V
0.3A MAX
POWER
12V
0.3A MAX
IPL PRO S3
LAN / PoE
G
Tx Rx
RTSCTS
COM
G
Tx Rx
RTSCTS
COM 1
G
Tx Rx
RTSCTS
COM 3
G
Tx Rx
RTSCTS
COM 2
G
Tx Rx
RTSCTS
COM 1
G
Tx Rx
RTSCTS
COM 3
G
Tx Rx
RTSCTS
COM 2
G
Tx Rx
RTSCTS
COM 4
G
Tx Rx
RTSCTS
COM 6
G
Tx Rx
RTSCTS
COM 5
LAN / PoE
IPL PRO S6
IPL PRO S1
LAN / PoE
POWER
12V
0.3A MAX
POWER
12V
0.3A MAX
34211G
7865G
GSGS
INPUT
2
1 2
GSGS
78
GSGS
78
GSGS
78
3 4
5 6 7 8
RELAYS
LAN / PoE
LAN / PoE
IR/SERIAL
IPL PRO CR88
IPL PRO IRS8
MAC: 00-05-A6-XX-XX-XX
S/N: ####### E######
MAC: 00-05-A6-XX-XX-XX
S/N: ####### E######
MAC: 00-05-A6-XX-XX-XX
S/N: ####### E######
MAC: 00-05-A6-XX-XX-XX
S/N: ####### E######
00-05-A6-XX-XX-XX
MAC: 00-05-A6-XX-XX-XX
S/N: ####### E######
MAC: 00-05-A6-XX-XX-XX
S/N: ####### E######
MAC: 00-05-A6-XX-XX-XX
S/N: ####### E######
00-05-A6-XX-XX-XX
5-pole COM
RS-232 ports
5-pole COM
RS-232/RS-422/
RS-485 ports
MAC
addr
ess
Power
input
connector
Power
input
connector
MAC
address
MAC
addr
ess
LAN/PoE (Ethernet)
connector and LEDs
5-pole COM
RS-232 port
LAN/PoE
(Ethernet)
connector and LEDs
LAN/PoE (Ethernet)
connector and LEDs
Contact
input
ports
Relay
ports
MAC
addr
ess
Power
input
connector
MAC
addr
ess
LAN/PoE (Ethernet)
connector and LEDs
LAN/PoE (Ethernet)
connector and LEDs
IR/Serial output
ports
Figure 3. IPL Pro Series Rear Panel Features
Panels and Locations of Features
Location and quantity of LEDs and corresponding connectors vary by model, but the functions and port wiring are identical
across models for each port type.

5
Cabling and Features
Attach cables using the following wiring diagrams as a guide. Full details are available in the IPLPro Series User Guide.
ATTENTION:
• Installation and service must be performed by experienced personnel.
• L’installation et l’entretien doivent être effectués par du personnel expérimenté.
Power
POWER
12V
X.XA MAX
R
Ridged
Smooth
Ground all devices.
+12 VDC input
– Return
Ridged
Smooth
To
AC
power
Front Panel
Tie Wrap
3/16"
(5 mm)
Max.
Rear
Panel
NOTE: Check the polarity of the power
supply before connecting it to the IPL.
Power Input, External Power Supply
• Front panel LED ( ) blinks during
boot-up and remains lit when the
IPL is powered and operational.
• Connect to
included 12 VDC
power supply.
External
Power Supply
(12 VDC, 0.5 A max.,
Extron
P/N 28-331-57LF)
NOTE: IPL Pro Series control processors accept power over Ethernet (PoE) through
the LAN port in addition to network communication (see Control - LAN (Ethernet) on
page6 for cabling and details). Both an external power supply and PoE can be
connected to the control processor simultaneously. The IPL uses PoE when it is available
but can switch seamlessly to the external 12VDC power supply if the PoE connection is
dropped.
ATTENTION:
• Always use a power
supply supplied or
specified by Extron.
Use of an unauthorized
power supply voids all
regulatory compliance
certification and may
cause damage to the
supply and the unit.
• Utilisez toujours une
source d’alimentation
fournie par Extron.
L’utilisation d’une
source d’alimentation
non autorisée annule
toute certification
de conformité
réglementaire et peut
endommager la source
d’alimentation que
l’unité.

6
IPL Pro Series • Setup Guide (Continued)
Control — Serial (COM)
G
Tx Rx
RTS CTS
COM 1
G
Tx Rx
RTS CTS
COM 4
COM
312 645
RTS
CTS
Tx
Rx
COM
RTS
CTS
Tx
Rx
NOTE: If you use cable that has a drain wire, tie the drain wire to ground at both ends.
Strip wires
3/16" (5 mm)
max.
Receive (Rx)
Transmit (Tx)
Projector, Panel
Display, PC, or
Other RS-232,
RS-422, or
RS-485 Device
Request to send
Clear to send
Transmit
Rx Receive
Tx
CTS
RTS
GGround
T
T
Tx
T
R
Front Panels
Select protocol via software.
COM port default protocol:
• 9600 baud
• 8 data bits • 1 stop bit
• no parity • no ow control
NOTE: The 5-pole COM ports support both
hardware and software ow control.
Heat ShrinkHeat Shrink
Over Shield Wires
To 5-pole
COM port
RTS = Request to Send
CTS = Clear to Send
Tx = Transmitting Data
Rx = Receiving Data
Serial (COM) Ports
Rear Panels
5-pole COM
(RS-232, RS-422*, RS-485*)
*See the Serial Options
table for which port
supports which standards.
RS-232
Tx
Rx
Ground
RTS
CTS
RS-422*
Tx-
Rx-
Ground
Tx+
Rx+
RS-485*
Ground
5-pole COM Pin Configurations
Data-
(pins 1 & 2
tied together)
Data+
(pins 4 & 5
tied together)
Pin
1(Tx)
2(Rx)
3(G)
4(RTS)
5(CTS)
*See the Serial Options table of supported
formats for each port.
Control — LAN (Ethernet)
1000
LINK
ACT
LAN / PoE
I
I
PL
PR
PR
O
S
6
5-A6-
XX-XX-XX
### E######
5-A6-XX-XX-XX
Rear Panel Front Panel
RJ-45
Connector
Insert Twisted
Pair Wires
Pins: 12345678
1000 Mbps
Connection
Network is
active.
Data is being
sent/r
eceived.
Link
LED
Activity
LED
LAN/PoE (Ethernet)
Default protocol:
• IPL IP address: 192.168.254.250
• Gateway IP address: 0.0.0.0
• Subnet mask: 255.255.255.0
• DNS address: 127.0.0.1
• DHCP: off
• Link speed and duplex level:
autodetected
• Data rates: 10/100/1000Base-T
Power over Ethernet (PoE):
If PoE is available, the IPL uses PoE.
If PoE is dropped (disconnects), the
IPL switches seamlessly to the
external 12 VDC power supply, if it
is installed.
Default login credentials:
• Username: admin
• Password: extron
Ethernet
PC
Touchlink Pro
Touchpanel
Extron Devices
(Switchers, Scalers)
TCP/IP
Network
The control processor is assigned a unique user hardware ID number (MAC address) (for example,
00-05-A6-05-1C-A0). You may need this address during configuration of the control processor. A
label that indicates the MAC address is located on the rear panel of the unit.
NOTE: The supported serial formats vary depending on the COM port,
as shown at right.
RS-232
Only
RS-232, RS-422,
or RS-485
Serial Options
Model COM Port
1
IPL Pro S1
1
2, 3
IPL Pro S3
1
2, 3, 4, 5, 6
IPL Pro S6
MAC: 00-05-A6-XX-XX-XX
S/N: ####### E######
00-05-A6-XX-XX-XX
MAC: 00-05-A6-XX-XX-XX
S/N: ####### E######
MAC
Address

7
Control — IR/Serial
IR/SERIAL
6
5
7
8
2
1
3
4
GSGS
12
GSGS
78
GSGS
78
GSGS
78
IR/SERIAL
Rear Panel Front Panel
S
G
(-)
(+)
(-)
(+)
(+)
(-)
To the IR Receiver of a
Projector, Display, or
Source Device
Two Single IR Emitters
Ground
IR Output
Unidirectional
IR
or
IR or RS-232
Output
Ground
3/16"
(5 mm)
max.
IR/S LEDs
Light when signals are transmitted
on the corresponding IR/serial port.
To a Projector,
Panel Display,
or the Wired
IR Remote or
RS-232 Port of
a Source Device
IR/Serial Ports
Output options:
• IR (30 kHz to 300 kHz,
with or without carrier signals)
• Unidirectional RS-232
Control — Input (Contact Closure Input)
3421G
7865G
INPUT
3
4
1
2
7
8
5
6
INPUT
Input (Contact closure input)
Each port senses external switch or contact closure by using a
1k ohm pull-up resistor in a TTL (5VDC) circuit.
Use these ports to monitor or trigger events and functions
(toggle relays, issue commands, send e-mail), once congured.
Input LEDs
Light when the
corresponding
ports are active
(tied to ground,
logic low).
Rear PanelFront Panel
(Switches, sensors,
relays, or similar
items)
Share the same ground
among contact input
connections.
Switch,
Sensor
2
1
3
4
G
Heat
Shrink
Over
Shield
Wires Ground
Device 4
Device 3
Device 2
Device 1
Wire
Nut
Control — Relay
1 2 3 4
5 6 7 8
RELAYS
3
4
1
2
7
8
5
6
RELAYS
Rear PanelFront Panel
1
5
Normally
Open
Common
To
Room Control
Equipment
Relay LEDs
Light when the
corresponding relays
are activated (tied to
GND, closed).
All relays are
normally open.
Relays
• Connect devices for relay control.
• Do not exceed a total of 24V at 1A for each port.

8
IPL Pro Series • Setup Guide (Continued)
Reset Modes: a Brief Summary
The IP Link Pro control processors offer the following reset modes:
• Use Factory Firmware: Press and hold the front panel Reset button while applying power to the unit. Keep holding the
button down until the Power LED blinks twice, or for 6 seconds, then release the button. The
control processor enters factory firmware mode. For units with firmware prior to version 2.x, the
LED blinks quickly. Use this mode to revert to factory firmware in the event of a firmware failure.
Do not continue to operate the control processor using the factory firmware version. If you want
to use the factory default firmware version, you must upload that version again.
• Project Recovery: See the IPL Pro Series User Guide for instructions. Use this mode to recover the project in the
event of a lost user name and password.
• Run/Stop Program: Hold down the Reset button for about 3 seconds, until the Power LED blinks once. Release
and press the Reset button momentarily (for <1second) within 1second. (Nothing happens if
the momentary press does not occur within 1second.) The LED blinks 2 times if the program is
starting. The LED blinks 3 times if the program is stopping. This mode allows you to restart any
programs stopped by an IP settings reset.
• Toggle DHCP Client: Press the Reset button five times (consecutively). Release the button. Do not press the button
within 3seconds following the fifth press. Use this mode to enable or disable the DHCP client
for the LAN port.
• The Reset LED blinks 6 times if the DHCP client is enabled.
• The Reset LED blinks 3 times if the DHCP client is disabled.
NOTES:
• DHCP toggle mode is supported on firmware version 3.0 or higher.
• By default DHCP is off and the unit uses a static IP address.
• When you disable the DHCP client, the unit reverts to using the previously-set static
IP address.
• Reset All IP Settings: Press and hold the front panel Reset button for 6 seconds. After the Power LED blinks twice,
release and momentarily press the Reset button. Use this mode to reset all network settings
to factory default values without affecting user-loaded files. This reset mode also stops any
running programs.
• Reset to Factory Defaults: Press and hold the front panel Reset button for 9 seconds. After the Power LED blinks
three times, release and momentarily press the Reset button. Use this mode to return the
control processor to factory default settings. This mode also deletes all user-loaded files and
configurations.
For detailed information on each mode and its use, see the IPL Pro Series User Guide at www.extron.com.
Resources
Obtaining Control Drivers
Extron provides an extensive selection of device drivers available on the
Extron website. If the system requires a control driver that is not already
available, you have the following options:
• You can request a new serial (RS-232) or Ethernet driver from Extron.
• Create your own custom IR device driver using Extron
IRLearnerPro software. Follow the directions in the IRLearner
Pro Help File to create a driver by using the remote control for
that device and the IR receiver port on the front panel of the
IPLProIRS8.
Obtaining Instructions, Information,
and Assistance
A checklist of basic setup steps is provided at the
beginning of this guide. For additional information
see the help files and the IPLProSeries User
Guide, available at www.extron.com.
If you have questions during installation and
setup, call the ExtronS3 Sales & Technical
Support Hotline or the ExtronS3 Control
Systems Support Hotline [phone]).
Rev. B: Changed wording of various items in the reset
modes summary:
For the Use Factory Firmware mode, changed
“replace” to “revert to factory”. Added more text
to clarify how long to hold the button, and on LED
behavior for units with versions prior to 2.x.
Per peer reviewer (Sean), added “ Do not continue
to operate the control processor using the factory
firmware version. If you want to use the factory
default firmware version, you must upload that
version again. “
For the Reset All IP Settings mode, added “to factory
default values” and noted that the mode stops
running scripts/events.
Rev. B: Added Run/Stop Program mode and new
DHCP toggle mode.
Since rev. A: changed “ollowing” to “following” in the first sentence on pg. 7.
Corrected IPCP to IPL in the name of the user guide in the last sentence of the reset
modes summary section.

9
Locating Software, Firmware, and Driver Files on the Extron Website
There are three main ways to find software, firmware, and device drivers within www.extron.com:
• Via links from the web page for the specific product
• Via the Download page (Click on the Download tab at the top of any page within www.extron.com.)
• Via links from search results
NOTES:
• For some software you have the option to click the Download Now button to begin downloading the
software le. For other software there is a link for contacting an Extron support representative who can
provide you access to the latest version.
To obtain Extron control product software, you must have an Extron Insider account. Extron provides
training to our customers on how to use the software. Access to the full features of Global Congurator
Professional is available to users who successfully complete Extron Control Professional Certication.
• New RS-232 and Ethernet drivers are required. You must use serial and Ethernet drivers developed
specically for the IPLinkPro platform. With the exception of IR device drivers, drivers used for the
previous generation IPLink (non-Pro) control processors are not compatible.

10
IPL Pro Series • Setup Guide (Continued)
© 2014-2018 - Extron Electronics All rights reserved. All trademarks mentioned are the property of their respective owners. www.extron.com
68-2437-51
Rev. B
08 18
Overall Configuration Procedure for the Control Processor
Configure the IP settings of
the control processor and the
TouchLink Pro touchpanels.
See Network
Communication Setup
Create GUI layouts for the
touchpanels or other interfaces:
1. Start GUI Designer.
2. Create GUI layout designs for each
TouchLink Pro, third party
touchpanel (with a TouchLink
Interface), or a computer or
mobile device (with LinkLicense).
3. Save and build the GUI layout le.
Or...
Download existing GUI layouts
from identical touchpanels.
Create monitors, schedules, timers,
macros, and local variables.
Add touchpanels or other interfaces
(if used) to the project.
Congure ports on the
control processor.
Import GUI layouts and congure the
touchpanels or other interfaces.
Test the system, make adjustments,
nalize conguration.
Save the project.
Build and upload the conguration to
the control processor.
If desired or required, install a new
security certicate (via Toolbelt).
Will
TouchLink Pro or
third party touchpanels or
other user interfaces
be used?
No Yes
Create a new GC Professional or GC Plus project
and add the control processor to it.
Within Global Configurator
(GC Professional or
GC Plus mode):
Figure 4. Overall Configuration Steps
See Network
Communication Setup
on page3
For information on safety guidelines, regulatory compliances, EMI/EMF compatibility, accessibility, and related topics, see the
Extron Safety and Regulatory Compliance Guide on the Extron website.