Extron electronics FLEX55 AC Plus USB 130 US User manual

1
IMPORTANT:
IMPORTANT:
Go to www.extron.com for the complete
user guide, installation instructions, and
specifications before connecting the
product to the power source.
FLEX55 AC+USB 130 US • Setup Guide
The Flex55 AC+USB 130 US Power Module provides AC, USB Type-A and USB Type-C power outlets for powering
and charging compatible mobile devices. The following guide provides the steps to install and secure the power
module to select Flex55 and Cable Cubby enclosures (see the ATTENTION below before installing the power
module).
The power module supplies up to 29.5 total watts.
NOTE: To view the power specifications, see www.extron.com.
Front Panel and Side Features
USB CHARGER 120V 50-60Hz 6A MAX
~
C C
B
Front View
Side View
A
USB CHARGER 120V 50-60Hz 6A MAX
~
C C
B
Front View
Side View
A
Figure 1. Flex55 AC+USB 130 US Power Module
AUSB Power Outlets:
• USB Type-A — supports up to 10 watts (5VDC up to 2A). When both USB ports are used, the Type-A port
drops to 0.5A.
• USB Type-C — supports up to 27 watts.
BAC Power Outlet — supports 120VAC, 50 to 60Hz, 6A Max.
CMounting Clips — there are four mounting clips on the unit, two on the top side of the module and two on the
bottom. These help secure the unit to the mounting frame or bracket.
ATTENTION:
• Always consult with a professional installer.
• Toujours consulter un installateur professionnel.
• Follow all national and local building and electrical codes that apply to the installation site.
• Respectez tous les codes électriques et du bâtiment, nationaux et locaux, qui s’appliquent au site de
l’installation.
• The installation must always be in accordance with the applicable provisions of National Electrical Code
ANSI/NFPA 70, article 725 and the Canadian Electrical Code part 1, section 16. The power supply shall not
be permanently fixed to building structure or similar structure.
• Cette installation doit toujours être conforme aux dispositions applicables du Code américain de l’électricité
(National Electrical Code) ANSI/NFPA 70, article 725, et du Code canadien de l’électricité, partie 1, section
16. La source d’alimentation ne devra pas être fixée de façon permanente à une structure de bâtiment ou à
une structure similaire.

2
FLEX55 AC+USB 130 US • Setup Guide (Continued)
Installing the Flex55 AC+USB 130 US Power Module
The following illustrations show the process for installing the Flex55 AC+USB 130 US Power Module into the Cable
Cubby Flex55 compatible enclosure.
Figure 2. Installing the Flex55 AC+USB 130 US
USB CHARGER 120V 50-60Hz 6A MAX
~
Extron
Flex55 AC+USB 130 US
Extron Cable Cubby
F55 UT enclosure
Insert the module
into the enclosure, frame
or bracket.
Connect any additional
devices or modules
Connect to
power source
2
4
3
1
Extron Cable Cubby
F55 UT enclosure
Using cutting pliers, carefully
snip and remove either the
center, left, or right support.

3
Removing the Flex55 AC+USB 130 US
The following illustration shows the process for removing the Flex55 AC+USB 130 US Power Module from the Cable
Cubby F55 UT enclosure, using the provided pry tool. This process applies to any compatible Flex55 and Cable
Cubby enclosure.
USB CHARGER 120V 50-60Hz 6A MAX
~
1
Locking
Tab
Insert pry tool
at the locking
tab location.
1
Unlock the other locking
tabs if applicable and
remove the module.
Pivot the pry tool away from
the module to unhook each
locking tab from the
mounting bracket.
2
3
Figure 3. Flex55 AC+USB 130 US Power Module Removal

4
68-3652-50 Rev. A
06 21
For information on safety guidelines, regulatory compliances, EMI/EMF compatibility, accessibility, and related topics, see the
Extron Safety and Regulatory Compliance Guide on the Extron website.
© 2021 Extron — All rights reserved. www.extron.com
All trademarks mentioned are the property of their respective owners.
Worldwide Headquarters: Extron USA West, 1025 E. Ball Road, Anaheim, CA 92805, 800.633.9876