Extron electronics CrossPoint 82 DTP2 User manual

1
IMPORTANT:
IMPORTANT:
Go to www.extron.com for the complete
user guide, installation instructions, and
specifications before connecting the
product to the power source.
DTP2 CrossPoint®82• Setup Guide
The Extron DTP2 CrossPoint 82 is an eight-input seamless scaling presentation matrix switcher that supports signal
resolutions up to 4K @ 60 Hz at 4:4:4. All models feature DisplayPort, HDMI, and DTP2 inputs, an HDMI output and a scaled
DTP2 output extension to send video, audio, and control signals up to 330 feet (100 meters) over a shielded CATx cable. The
DTP2 CrossPoint 82 IPCP SA and DTP2 CrossPoint 82 IPCP MA 70 models each have a built-in Extron IPCP Pro 355M IP Link
Pro Control Processor, and an integrated 100 watt class D power amplier. The DTP2 CrossPoint 82 delivers high image quality,
fast and reliable switching, Extron Pro DSP audio processing, seamless video transition effects, logo keying, and HDMI loop out.
The switchers can be controlled and congured over Ethernet, RS-232, or USB.
This guide provides instructions for an experienced user to set up and congure the DTP2 CrossPoint 82 (base model),
DTP2 CrossPoint 82 IPCP SA, and DTP2 CrossPoint 82 IPCP MA 70 switchers. It covers how to perform basic operations using
the front panel controls and selected Simple Instruction Set™ (SIS) commands.
NOTES:
• For full installation, configuration, menus, connector wiring, and operation details, see the DTP2 CrossPoint 82 User
Guide at www.extron.com. For installation, configuration, and operation details of the embedded IPCP Pro 355M, see
the IPCP Pro Series User Guide.
• The DTP2 CrossPoint 82 products can also be configured via the Extron Product Configuration Software (PCS),
available at www.extron.com. For information on using PCS, see the DTP2 CrossPoint 82 Help File.
Installation
DTP2 CrossPoint 82 Rear Panel Connectors
Figure 1 shows the rear panel of the DTP2 CrossPoint 82 IPCP SA. The DTP2 CrossPoint 82 IPCP MA 70 rear panel is the same
except that the embedded amplier is 70 V mono while the SA model amplier is stereo. The DTP2 CrossPoint 82 base model
rear panel does not have an embedded IPCP Pro 355M module (see gure 1, Q) or amplier module (O).
DTP2 CROSSPOINT 82 IPCP SA
INPUTS (DTP2/XTP)
LOOP OUT
31
2
5
46 7
SIG LINK
IN
8
SIG LINK
IN
OUTPUTS (DTP2/XTP/HDBT) AUDIO INPUTS OUTPUTS REMOTE
HDMI/CEC
OVER TP
12
SIG LINK
OUT Tx Rx
IR
G
LAN
AV LAN 2 AV LAN 3
AV LAN 1
2x25W(8Ω)/2x50W(4Ω)
LR
CLASS 2 WIRING
AMPLIFIED OUTPUT
Tx Rx RTSCTS G Tx Rx GTxRxG
R
1234G
DIGITAL I/OCOM 3COM 2COM 1
SSGG
1
12 2C34C -S G+S+V
PWR OUT = 6W
RRRRRRRRRR
R
R
R
R
R
R
R
R
R
R
R
R
R
IR/SERIAL eBUSRELAYS
50-60 Hz
100-240V~ 2.0A MAX
Tx Rx
RS-232
G
RESET
12
34
+48V
+48V
1
2
MIC/LINE
LR
AUX
34
HDMI
HDMI
HDMI
HDMIDP
HDMI
HDMI
O
RQP
HJLM
IN
AC
BEFG
D
Figure 1. Rear Panel Connectors, DTP2 CrossPoint 82 IPCP SA
AAC power connector
BDisplayPort input connector (input 1)
CHDMI (with CEC) loop out connector
DDTP2/XTP input connectors (inputs 7
and 8)
EHDMI (with CEC) output connector
(output 1)
FScaled DTP2/DTP/HDBaseT (with CEC)
output connector (output 2)
GOver TP IR pass-through connector
HAnalog line audio inputs 3 and 4
IAnalog mic/line audio inputs 1
and 2 and adjacent phantom
power LEDs
JAnalog line audio outputs 1
through 4
KLAN connector
(DTP2 CrossPoint 82 base model
only, see the note and illustration
below.)
LRemote RS-232 connector
MReset LED
NReset button
OAmplified audio output (IPCP
models only)
PAux analog line audio input
connector
QIPCP Pro 355M Control Processor
(IPCP models only)
RHDMI inputs 2 through 6
NOTE: The DTP2 CrossPoint 82 base model has a LAN connector to the left of the Remote
RS-232 connector (see Kin the illustration at right) instead of the LAN and AV LAN ports on the
IPCP Pro 355M control processor.
50-60 Hz
100-240V ~1.0A MAX
31
2
5
46
HDMI/CEC
INPUTS (DTP2/XTP) OUTPUTS (DTP2/XTP/HDBT) AUDIO INPUTS
OUTPUTS REMOTE
OVER TP
DTP2 CROSSPOINT 82
7
SIG LINK
IN
81
SIG LINK
IN
2
SIG LINK
OUT
LOOP OUT
Tx Rx
RS-232
G
Tx Rx
IR
G
RESET
12
34
+48V
+48V
1
2
MIC/LINE
LR
AUX
34
LAN
HDMI
HDMI
HDMI
HDMI
HDMI
HDMIDP
RP
ACH
B
E
FG
DK

2
DTP2 CrossPoint 82 • Setup Guide (Continued)
Mounting and Cabling
Step 1 —Mount the device
a. Turn off or disconnect all equipment power sources.
b. Mount the DTP2 CrossPoint 82 to a rack using the pre-installed side mounting brackets, or remove the brackets and use an
optional 19-inch rack shelf (see the mounting instructions provided with the kit, available at www.extron.com). The DTP2
CrossPoint 82 base model has a 1U high, full rack width enclosure. The DTP2 CrossPoint 82 IPCP models have 2U, full rack
enclosures.
Step 2 —Connect inputs
Make the following input connections as needed:
• Connect a DP source to the Input 1 DisplayPort connector (see figure 1, B, on the previous page).
• Connect HDMI or DVI (with an appropriate adapter) sources to HDMI input connectors 2 through 6 (R).
• Connect DTP2 transmitters to DTP2/XTP RJ-45 input connectors 7 and 8 (D). These connectors also allow for remote
powering of DTP2 transmitters. You can configure the TP inputs for XTP mode via SIS commands, the on-screen
display (OSD), or PCS (see the DTP2 CrossPoint 82 Help File). For cable wiring and recommendations, see Twisted Pair
Recommendations for DTP2, XTP, and HDBaseT Communication on the next page.
• Connect analog audio sources to:
• The 5-pole captive screw line audio input connectors 3 and 4 (H) and the Aux connector (P) for balanced or
unbalanced stereo audio (Aux connector) or dual mono audio (connectors 3 and 4). The Aux Line input is shared and can
be associated with one or more video inputs.
• Connect balanced or unbalanced mic or line level inputs to 3-pole Mic/Line captive screw connectors 1 and 2 (I).
These inputs support optional +48 VDC phantom power, which is indicated by the LEDs at the left of the connectors.
Step 3 —Connect outputs
Make the following output connections as needed:
• Connect an HDMI, or DVI with an appropriate adapter, display to HDMI/CEC output connector 1 (E).
• Connect a DTP2 endpoint, XTP matrix switcher, or HDBaseT compatible receiver to output connector 2 (F). For cable wiring
and recommendations, see Twisted Pair Recommendations for DTP2, XTP, and HDBaseT Communication.
• To pass infrared data, connect a control device to the 3-pole Over TP IR captive screw connector (see IR Over TP Wiring
on the next page). Alternatively, insert RS-232 communication to a DTP2/XTP/HDBaseT endpoint via Ethernet (see the
DTP2 CrossPoint 82 User Guide for more information).
• Connect balanced or unbalanced analog audio output devices to one or both 5-pole captive screw output connector pairs
1 and 2 or 3 and 4 (J). These connectors are configurable as four discrete mono outputs or as two stereo inputs (see Audio
Wiring on the next page for more information).
• For IPCP models, connect speakers to the amplifier module via the 5 mm 4-pole stereo (DTP2 CrossPoint 82 IPCP SA) or
2-pole mono (DTP2 CrossPoint 82 IPCP MA 70) Amplified Output connector (O).
Step 4 —Connect control devices
• To control the DTP2 CrossPoint 82 base model through Ethernet, connect a LAN or WAN to the LAN connector (K). To wire
the RJ-45 connector to the cable, see Twisted Pair Recommendations for DTP2, XTP, and HDBaseT Communication.
For the IPCP models, connect a LAN or WAN to any of the AV LAN connectors in the IPCP Pro control processor panel (Q).
The default IP address of the switcher is 192.168.254.254. The default subnet mask is 255.255.255.0. The default gateway
address is 0.0.0.0.
• For serial RS-232 control, connect a host device to the 3-pole captive screw connector (L). The baud rate is 9600.
• For control through USB, connect a host device to the front panel USB mini-B Config port (see figure 2, Aon page 4).
Step 5 —Set up the IPCP Pro 355M control processor (IPCP models only)
The Extron IPCP Pro 355M control processor (see figure 1, Q) provides monitoring and control of a variety of external devices,
such as projectors and lights. See the IPCP Pro Series Setup Guide, available at www.extron.com, for installation details.
Step 6 —Connect power
Connect a 100 to 240 VAC, 50-60 Hz power source to the AC power connector (A).

3
Twisted Pair Recommendations for DTP2, XTP, and HDBaseT Communication
Extron recommends using the following practices to achieve full transmission distances
and reduce transmission errors:
• Use Extron XTP/DTP2 24 SF/UTP cables for the best performance. At a minimum,
Extron recommends 24 AWG, solid conductor, shielded twisted pair (STP) cables with
a minimum bandwidth of 400 MHz.
• Terminate cables with shielded connectors to the TIA/EIA-T568B standard (shown at
right).
• Limit the use of more than two pass-through points, which may include patch points,
punch down connectors, couplers, and power injectors. If these pass-through points
are required, use shielded couplers and punch down connectors.
ATTENTION:
• Do not connect these connectors to a telecommunications or computer data
network.
• Ne connectez pas ces ports à des données informatiques ou à un réseau de
télécommunications ou de données informatiques.
• DTP2 remote power is intended for indoor use only. No part of the network that
uses DTP2 remote power should be routed outdoors.
• L’alimentation DTP2 à distance est destiné à une utilisation en intérieur
seulement. Aucune partie du réseau qui utilise l’alimentation DTP2 à distance
ne peut être routée en extérieur.
NOTE: When using shielded twisted pair cable in bundles or conduits, consider the following:
• Do not exceed 40% fill capacity in conduits.
• Do not comb the cable for the first 65 feet (20 meters), where cables are straightened, aligned, and secured in tight
bundles.
• Loosely place cables and limit the use of tie wraps or hook-and-loop fasteners.
• Separate twisted pair cables from AC power cables.
Audio Wiring
Wire the audio input and output connectors as shown at right. Use
the supplied tie wrap to strap the audio cable to the extended tail
of the connector. This does not apply to the amplied audio output
connector on the SA and MA models.
ATTENTION:
• For unbalanced outputs, do not connect wires to the
“-” poles (see the illustration at right).
• Pour les sorties asymétriques, ne connectez pas de
câbles aux pôles «-» (voir l’illustration de droite).
NOTE: The length of exposed wires is critical. The ideal length
is 3/16 inch (5 mm).
IR Over TP Wiring
To transmit and receive IR signals, connect a control device to the
three-pole Over TP IR connector (Tx, Rx, and G).
NOTE: RS-232 data can be inserted via Ethernet only (see the
DTP2 CrossPoint 82 User Guide for details).
TIA/EIA-T568B
Pin Wire Color
1 White-orange
2 Orange
3 White-green
4 Blue
5 White-blue
6 Green
7 White-brown
8 Brown
12345678
RJ-45
Connector
Insert Tw isted
Pair Wires
Pins:
Balanced Audio Output
Tip
Ring
Tip
Ring
Slee
ves
Unbalanced Audio Output
Tip
No Ground Here
No Ground Here
Tip
Sleeves
LR
LR
Unbalanced Audio InputBalanced Audio Input
Tip
Ring
Tip
Ring
Sleeves
Tip
Sleeve
Sleeve
Tip
LR
LR
Do not tin the wires!
A
udio Inputs and Outputs 1 – 4 and Aux
Mic/Line Inputs 1 and
2
Balanced Audio Input
Tip
Slee
ve
Ring
Unbalanced Audio Input
Tip
Sleeve

4
DTP2 CrossPoint 82 • Setup Guide (Continued)
Front Panel Overview
Figure 2 shows the front panel of the DTP2 CrossPoint 82 IPCP SA and IPCP MA 70. The DTP2 CrossPoint 82 base model is 1U
high and has no IPCP Pro LEDs (I).
ENTER
MENU
1
2
OUTPUTS
DTP2 CROSSPOINT 82
DIGITAL PRESENTATION MATRIX
2
A
BFG
I
H
CE
D
Figure 2. Front Panel Features, DTP2 CrossPoint 82 IPCP SA and DTP2 CrossPoint 82 IPCP MA 70
AConfig port
BInput selection buttons (1 through 8)
CLogo button
DOutput selection buttons
ESignal and Status LEDs
FMenu and Enter buttons
GNavigation buttons
HMic and Volume knobs and LEDs
IIPCP Pro LEDs (IPCP models only)
A Front panel configuration port — Connect a host device to the USB mini-B port for device configuration, control, and
firmware upgrades.
B Input selection buttons (1 through 8) — Press one of these buttons to select an input. The buttons light amber for audio
and video, green for video only, or red for audio only.
CLogo button — Selects a logo slot to be displayed on the scaled DTP2 output (not available on the HDMI output).
1. Press and hold the button until the buttons light for the inputs to which a logo has been assigned.
2. Press the button for the input with the desired logo (1through 8, slots 9-16 are available via SIS commands only).
See the DTP2 CrossPoint 82 User Guide at www.extron.com or the DTP2 CrossPoint 82 Help File for more information
about adding and selecting logos.
D Output selection buttons (1 and 2) — Press one of these buttons to select the output on which the selected input is
displayed. Button 1 selects HDMI output 1, which is not scaled. Button 2 selects DTP2/XTP/HDBT output 2, which is scaled.
These buttons can select different inputs to display on the two outputs or they can select the same input for both outputs.
E Status LED indicators
• Input signal LEDs — Eight LEDs light green for their corresponding inputs when active video content is detected on
that input.
• Output signal LEDs — Output LEDs 1, 2, and Loop light green when the output is connected to a display, and blink
amber when output video and sync are disabled.
• Input HDCP LEDs — Eight LEDs light green for each input signal that is HDCP-encrypted.
• Output HDCP LEDs — Three LEDs light green for an output when it is currently HDCP-encrypted.
• DTP and DTP2 Input LEDs — Two LEDs light green if DTP or DTP2 power is enabled on the corresponding input.
• DTP and DTP2 Output LEDs — Two output LEDs light green if DTP or DTP2 power is enabled on DTP2 output 2.
F Menu and Enter buttons — Press these buttons to access and navigate the on-screen display menu system (scaled DTP2
output only, not available on the HDMI output).
G Navigation buttons — Press these buttons to navigate through the on-screen display menu system or change settings
(scaled DTP2 output only, not available on the HDMI output).
H Mic and Volume knobs and LED indicators — Rotate the Mic knob to adjust the microphone level. Rotate the Volume
knob to adjust the program or output volume level (configurable, see the DTP2 CrossPoint 82 Help File for more information).
The eight LED indicators for each knob light according to the level being adjusted. The LEDs light in order from bottom to top
to indicate steps from 1% (-99 dB) to 99% (-1 dB). The bottom LED blinks when the volume is muted. The top LED blinks
when the volume is at 100% (12 dB).
I IPCP Pro LED indicators — IPCP models only (see the IPCP Pro Series Setup Guide for details).

5
Firmware Updates
Download rmware updates from the Extron website and upload them via the internal web pages or PCS.
DTP2 CrossPoint 82 Configuration
To congure DTP2 CrossPoint 82, you can use the front panel controls, the internal web pages, PCS, SIS, or the on-screen
display (OSD) menu (DTP2 scaled output only).
On-screen Display (OSD) Menu System
NOTE: The OSD is available only via the DTP2 scaled output.
Displays connected to the unscaled HDMI output cannot display
the OSD.
To congure DTP2 CrossPoint 82 using the OSD menu, connect a display
to a DTP2/XTP matrix switcher/HDBaseT compatible device. The OSD
menu consists of eight submenus accessed using the front panel Menu or
Enter button (see the example at right).
Extron Product Configuration Software
To congure DTP2 CrossPoint 82 switchers using PCS, install the
software (available at www.extron.com) to a PC connected to the
switcher via Ethernet or front panel USB Cong port (see figure 2, A, on
page 1). After the installation, start the program. For full instructions, while
the program is running, press <F1> on the keyboard, click the ?button in
the software, or select the help le option from the device tab menu.
Internal Web Pages
To congure the DTP2 CrossPoint 82 using the factory-installed web pages in a web browser, connect the AV LAN connector
(IPCP models) or LAN connector (base model) to a LAN or WAN. The default IP address is 192.168.254.254. A password is
required the rst time the page is opened and remains in effect until changed or removed.
NOTE: The factory configured passwords for all accounts on this device have been set to the device serial number. In the
event of an absolute system reset, the passwords convert to no password. Passwords are case sensitive.
Basic SIS Command Table
To congure the DTP2 CrossPoint 82 with specic SIS commands via an RS-232, USB, or Ethernet connection, use the Extron
DataViewer utility or a control system to send and receive SIS commands. The table below lists a selection of SIS commands. For
a full list of SIS commands and variables, see the DTP2 CrossPoint 82 User Guide at www.extron.com.
Command ASCII Command Response Additional Description
Input Selection
Select audio and video input X!*X@! InX!*X@•All]Select audio and video from input X! to output X@.
Select video input only (applies to
scaled DTP2 output only)
X!*2% InX!•2•Vid]Select the video only from input X! to output 2.
Select audio input only (applies to
scaled DTP2 output only)
X!*2$ InX!•2•Aud]Select the audio only from input X! to output 2.
Auto-Image
Execute Auto-Image™1*0A Img*0]Execute an Auto-Image (follows aspect ratio setting).
Execute Auto-Image and ll 1*1A Img*1]Execute an Auto-Image and ll the output raster.
Execute Auto-Image and follow 1*2A Img*2]Execute an Auto-Image and follow the input aspect ratio.
Loop Out Input Selection
Set loop out input EX!LOUT}LoutX!]Tie the loop output to input X!.
View loop out input ELOUT}X!]View the loop out input. Default = 1
KEY:
X! = Input selection 1through 8, 9(Aux audio, selectable for scaled DTP2 output only)
X@ = Output selection 1= matrix output 1 (HDMI/DVI) 2= scaled output 2 (DTP2/XTP/HDBT)

668-3438-50 Rev. A
01 20
© 2020 Extron Electronics — All rights reserved. www.extron.com All trademarks mentioned are the property of their respective owners.
Worldwide Headquarters: Extron USA West, 1025 E. Ball Road, Anaheim, CA 92805, 800.633.9876
DTP2 CrossPoint 82 • Setup Guide (Continued)
Command ASCII Command Response Additional Description
Video Mute
Mute output video X@*1B VmtX@*1]Mute the video on output X@.
Mute video on all outputs 1B Vmt1]Mute the video on all outputs.
Mute video and sync 2B Vmt2]Mute the video and sync on all outputs.
Unmute video and sync 0B Vmt0]Unmute the video on all outputs.
View output mute status B VmtX4@1•X4@2•X4@3]View mute status X4@ for outputs 1, 2, and loop (3).
Audio Configuration
Set audio input format EIX!*X5*AFMT}AfmtIX!*X5*]Set the audio format of input X! to X5*.
View audio input format EIX!AFMT}X5*]View the audio format of input X!.
Front Panel Lockout (Executive Modes)
Enable lock mode 1 1X Exe1]Lock all front panel controls.
Enable lock mode 2 2X Exe2]Lock the front panel except for input selection, logo
conguration, and volume adjustment.
Enable lock mode 3 3X Exe3]Lock the front panel except for input selection and logos.
Enable lock mode 4 4X Exe4]Lock the front panel except for volume adjustment.
Disable executive modes 0X Exe0]Allow all front panel adjustments and selections.
IP Settings
Set switcher IP address EX8&CI}Ipi•X8&] Specify a new switcher IP address.
Set switcher DHCP mode EX( DH}Idh X1)] Enable or disable DHCP (0= default).
Set subnet mask EX8*CS}Ips•X8*] Specify a new subnet mask.
Set gateway IP address EX8(CG}Ipg•X8(] Specify a new gateway IP address.
Reboot network E2BOOT}Boot2]Restart network connection after IP or DHCP changes.
NOTE: IP settings do not take effect until the E2BOOT}command is executed.
Twisted Pair Protocol
Set input TP type EIX!*X6&HDBT}HdbtIX!*X6&] Set the DTP2/XTP type for input X! to X6&.
View input TP type EIX!HDBT}X6&] View the current DTP2/XTP type for input X!.
Set output TP type EO2*X6&HDBT}HdbtO 2*X6&] Set the TP type for input X! to X6&.
View output TP type EO2HDBT}X6&] View the DTP2/XTP/HDBT setting X6& on output 2.
DTP Remote Power Parameters
Set input remote power EIX!*X6^RPWR}RpwrIX!*X6^] Set remote power on input X! to X6^.
View input remote power EIX!RPWR}X6^] View remote power setting on input X!.
Set output 2 remote power EO2*X6^RPWR}RpwrO 2*X6^] Set remote power on output 2 to X6^.
View output 2 remote power EOX@RPWR}X6^] View remote power setting on output .
KEY:
X! = Input selection Inputs 1 through 8. For the Twisted Pair Protocol commands, X! = Inputs 7 and 8 only.
X@ = Output selection 1= Output 1 (HDMI/DVI), 2= Output 2 (DTP2/XTP/HDBT)
X1) =Enable or disable 0= Off or disabled, 1= on or enabled
X4@ =Video mute status 0= Unmuted, 1= muted
X5* =Audio input type 0= None (input muted), 1= Analog aux line (5-pole captive screw), 2= LPCM-2Ch, 3= Multi-Ch,
4= LPCM-2Ch Auto (AUX) (default), 5= Multi-Ch Auto (AUX)
X6^ =DTP remote power 0= Off (No remote power, default), 1= DTP 12 VDC, 2= DTP 48 VDC
X6& =TP format 0= DTP2 format (default), 1= XTP, 2= HDBaseT format (supported on output only)
X8& =IP address Format nnn.nnn.nnn.nnn, 192.168.254.254 = default
X8* =Subnet mask Format nnn.nnn.nnn.nnn, 255.255.255.0 = default
X8( =Gateway address Format nnn.nnn.nnn.nnn, 0.0.0.0 = default
For information on safety guidelines, regulatory compliances, EMI/EMF compatibility, accessibility, and related topics, see the
Extron Safety and Regulatory Compliance Guide on the Extron website.