Extron electronics VNR 100 User manual

1
VNR 100 O/S Drive Replacement Kit • Setup Guide
The Extron VNR 100 Operating System (O/S) Drive Replacement Kit is an optional accessory for the VNR 100
recorder. The new drive is ready to be inserted into the recorder. It allows the recorder to be moved between secure
areas without compromising condential data.
There are four drive bays on the front panel of the VNR 100. From left to right, they are numbered 0 - 3. The
O/Sdrive is labelled number0.
b a
O/S Drive (drive #0) c
NOTES:
• The replacement drive does not have a default IP address assigned. This must be set by the user.
• The drive is licensed to run only on the VNR 100 for which it was supplied and cannot be used with any
other VNR 100 unit.
• A label xed to the top of the drive shows the serial number of the VNR 100 for which it is intended to
be used.
Replacing an Existing Drive
1. If necessary, switch the recorder off by pressing and
holding down the power switch (a) until the LEDs (b)
ash red and then go out.
ATTENTION: Never remove or insert the drive
while the unit is powered on.
2. Unplug the recorder.
3. Press the red catch. The lever arm is released (see the
gures to the right).
4. Swing the lever arm out until it is perpendicular to the
front of the drive caddy and use the arm to pull the
caddy out of the drive bay (see the gure to the right).
5. Remove the drive. There are no screws to be removed or
cable connections to be undone.
6. Insert the new drive into the drive bay.
7. Push the caddy into the recorder.
8. Swing the lever arm back until it clicks into place behind the catch.
ATTENTION: Do not power on the unit at this time.
Conguring the New Drive
1. Attach a mouse to the rear panel PS/2 mouse port (e) and a keyboard to the rear
panel PS/2 keyboard port (f). Alternatively, you may connect the mouse and
keyboard to the front panel USB ports (cin the gure at the top of the page) or
the rear panel USB ports (d).
2. Connect a VGA monitor to the rear panel port (g).
e
f
d
dg

2
68-2258-50 Rev. A
05 13
ExtronHeadquarters
+1.800.633.9876 (Inside USA/Canada Only)
Extron USA - West Extron USA - East
+1.714.491.1500 +1.919.850.1000
+1.714.491.1517 FAX [phone] FAX
ExtronEurope
+800.3987.6673
(Inside Europe Only)
+31.33.453.4040
+31.33.453.4050 FAX
ExtronAsia
+65.6383.4400
+65.6383.4664 FAX
ExtronJapan
+81.3.3511.7655
+81.3.3511.7656 FAX
ExtronChina
+86.21.3760.1568
+86.21.3760.1566 FAX
ExtronMiddleEast
+971.4.299.1800
+971.4.299.1880 FAX
ExtronKorea
+82.2.3444.1571
+82.2.3444.1575 FAX
ExtronIndia
1800.3070.3777
Inside India Only
+91.80.3055.3777
+91.80.3055.3737 FAX
© 2013 Extron Electronics All rights reserved. www.extron.com
VNR 100 O/S Disk Replacement Kit • Setup Guide (Continued)
3. Power on the recorder by pressing the front panel power switch
(ain the gure at the top of the previous page).
4. Power on the monitor. The login screen is displayed.
5. Enter the Username and Password.
NOTE: By default, the Username is matrix_rec and the
Password is matrix.
6. From the menu bar on the desktop, select Applications > Internet >
Firefox Web Browser.
7. In the browser address bar, enter the IP address of the recorder followed by a
colon and the port number.
NOTE: For a new drive, enter 127.0.0.1:8080.
The login page opens.
8. Enter the Username and Password.
NOTE: By default, the Username and Password are both config.
9. Click Login. The VNR 100 Recorder Settings page opens (see the gure to
the right).
10. Set the Network Settings and Recorder Settings as required.
11. Click Apply Changes.
12. Logout of the cong screen. The unit is ready for normal operation.
13. Power down the unit.
14. Remove the mouse, keyboard, and monitor.
Network settings [eth0]
Recorder settings
User settings
Data disk
IP Address
Subnet Mask
Gateway
Serial
Controller IP
Controller port
MTU
New password
Confirm New password
192.168.254.254
255.255.0.0
192.168.254.253
192.168.254.254
5432
1500
1111999
mounted to /home/matrix_rec/Recording_Files
Disk free space: 19GB->98% used
formated to ext3
status:
Umount
Format
Apply Changes Cancel Changes
Logout
VNMatrix recorder settings