Extron electronics USB HUB4 Series User manual

1
IMPORTANT:
IMPORTANT:
Go to www.extron.com for the complete
user guide, installation instructions, and
specifications before connecting the
product to the power source.
USB HUB4 Series • Setup Guide
This guide provides basic instructions for setting up the Extron USB HUB4 Series AAP and MAAP.
HUB4 USB MAAP HUB4 USB AAP
ACTIVITY ACTIVITY
USB HUB4 MAAP USB HUB4 AAP
ACTIVITY ACTIVITY
Installation
Step 1 — (Optional) Install the wall box or mounting bracket
If using an electrical wall box or a mounting bracket, install it in the wall or furniture (see Mounting in the USB HUB4 Series User
Guide available at www.extron.com).
Step 2 — Mount the HUB4 onto a mounting frame
Attach the USB HUB4 AAP or USB HUB4 MAAP to an appropriate AAP or MAAP sized mounting frame, rack space frame, or
other Extron architectural product (see Mounting in the USB HUB4 Series User Guide).
Step 3 — Connect the USB HUB4 to the host computer
For ease of installation, connect the USB HUB4 to the host computer in either of the following ways:
• Using the Type mini-B USB port: Connect a Type A to Type mini-B cable (provided) to the
USB mini-B port on the USB HUB4 rear panel.
• Using the green captive screw USB In port: Remove the Type B or Type mini B terminator
from a Type A to B or Type A to mini-B USB cable and insert the cable wires into the 5-pole
USB In port as shown below and at right. This method may be necessary if space is limited.
(See Connecting to the captive screw USB port in the USB HUB4 Series User Guide.)
NOTE: Choose one of these two methods to connect the HUB4 to the host computer.
Do not connect the host computer to both HUB4 ports at the same time.
Wire color Port
Braided shield
V+ (+5 VDC)
Red
S (Shield)
White D- (Data -)
Green D+ (Data +)
Black –(Ground)
USB IN
RWGB
+V D- D+ S
IN OUT
WIRE COLOR
POWER
12V
1.1A MAX
+
+
--
-
Braided Shield / S
Red / +V
White / D
-
Green / D+
Black /
USB Cable (6')
To Host
Computer
USB Port
Type A
USB
Strip 1"to 2"from the outer jacket
of the USB cable to expose the wires.
USB HUB4 AAP
Captive
Screw
USB
Connector
Type mini B
USB Connector
Mounting
Frame
Rear
Step 4 — (Optional) Wire power connector
The USB HUB4 can be powered by the host computer. However, if the USB peripheral devices
connected to the USB HUB4 require more power than the USB HUB4 can provide, wire an
optional Extron PS 1215 1.5 A, 12 VDC power supply to the 12VDC Power In ports 1 and 2 on the
rear panel, as shown at right.
ATTENTION:
• For use only with UL Listed Extron products which accept Architectural Adapter Plates
(AAPs) or Mini Architectural Adapter Plates (MAAPs).
• À utiliser uniquement avec les produits Extron certifiés UL qui acceptent des plaques
d’adaptation architecturale (AAP) ou des mini-plaques d’adaptation architecturale
(MAAP).
USB IN
RWGB
+V D- D+ S
IN OUT
WIRE COLOR
POWER
12V
1.1A MAX
+
+
--
-
SECTION A–A
Power Supply
Output cord
A

2
68-1735-50 Rev. C
08 22
For information on safety guidelines, regulatory compliances, EMI/EMF compatibility, accessibility, and related topics, see the
Extron Safety and Regulatory Compliance Guide on the Extron website.
© 2009-2022 Extron — All rights reserved. www.extron.com
All trademarks mentioned are the property of their respective owners.
Worldwide Headquarters: Extron USA West, 1025 E. Ball Road, Anaheim, CA 92805, 800.633.9876
Connecting additional Extron devices
If using an additional Extron device, such as a WM Series Extender, with the external power supply, connect the device power
cord to the 12 VDC Power Out ports 3 and 4 (see image below).
Maximum: Maximum peaking
and gain
Medium: Mid-level peaking
and gain
Normal: Unity gain
Circuit
board
Faceplate
www.extron.com
33-612-01 D
02 05
9-18 VDC
Power
L
Audio
R
EXTENDER WM AAP
AUDIO IN
USB HUB4 AAP
ACTIVITY
USB IN
RWGB
+V D- D+ S
IN OUT
WIRE COLOR
POWER
12V
1.1A MAX
+
+
--
-
Rear
Front
Extender WM AAP
USB HUB4 AAP Desktop Powe
r
Supply
Power Loop Out
Step 5 — (Optional) Mount unit in wall box
If using an electrical box, mount the USB HUB4 and the attached mounting frame onto the
box (see the image at right). If using a mounting bracket, this step is not needed.
Step 6 — Connect peripheral devices
Attach the peripheral USB devices to the front panel USB Type A ports.
Step 7 — Power on
Power on the host computer and the desktop power supply (if applicable). Check the front
panel power indicator LED to verify that the HUB4 is receiving power.
Wall opening
flush with
edge of box
Extron
CPM101
Mounting
Frame
Extron
USB HUB4
USB Hub
VTT001MAAP
POWER
USBHUB4 MAAP
ACTIVITY