Extron electronics WAP 100AC User manual

User Guide
TouchLink Accessories
WAP 100AC
Wireless Access Point
(2.4GHz b/g/n, 5GHz ac/a/n Indoor AP)
68-2984-01 Rev. A
09 16

Safety Instructions
Safety Instructions • English
WARNING: This symbol, D, when used on the product, is intended to alert
the user of the presence of uninsulated dangerous voltage within the
product’s enclosure that may present a risk of electric shock.
ATTENTION: This symbol, I, when used on the product, is intended to
alert the user of important operating and maintenance (servicing)
instructions in the literature provided with the equipment.
For information on safety guidelines, regulatory compliances,
EMI/EMF compatibility, accessibility, and related topics, see the
Extron Safety and Regulatory Compliance Guide, part number 68-
290-01, on the Extron website, www.extron.com.
Sicherheitsanweisungen • Deutsch
WARNUNG: Dieses Symbol Dauf dem Produkt soll den Benutzer
darauf aufmerksam machen, dass im Inneren des Gehäuses dieses
Produktes gefährliche Spannungen herrschen, die nicht isoliert sind und
die einen elektrischen Schlag verursachen können.
VORSICHT: Dieses Symbol Iauf dem Produkt soll dem Benutzer in
der im Lieferumfang enthaltenen Dokumentation besonders wichtige
Hinweise zur Bedienung und Wartung (Instandhaltung) geben.
Weitere Informationen über die Sicherheitsrichtlinien, Produkthandhabung,
EMI/EMF-Kompatibilität, Zugänglichkeit und verwandte Themen finden Sie in
den Extron-Richtlinien für Sicherheit und Handhabung (Artikelnummer
68‑290-01) auf der Extron-Website, www.extron.com.
Instrucciones de seguridad • Español
ADVERTENCIA: Este símbolo, D, cuando se utiliza en el producto, avisa
al usuario de la presencia de voltaje peligroso sin aislar dentro del
producto, lo que puede representar un riesgo de descarga eléctrica.
ATENCIÓ N: Este símbolo, I, cuando se utiliza en el producto, avisa
al usuario de la presencia de importantes instrucciones de uso y
mantenimiento recogidas en la documentación proporcionada con
el equipo.
Para obtener información sobre directrices de seguridad, cumplimiento
de normativas, compatibilidad electromagnética, accesibilidad y temas
relacionados, consulte la Guía de cumplimiento de normativas y
seguridad de Extron, referencia 68-290-01, en el sitio Web de Extron,
www.extron.com.
Instructions de sécurité • Français
AVERTISSEMENT : Ce pictogramme, D, lorsqu’il est utilisé sur le
produit, signale à l’utilisateur la présence à l’intérieur du boîtier du
produit d’une tension électrique dangereuse susceptible de
provoquer un choc électrique.
ATTENTION : Ce pictogramme, I, lorsqu’il est utilisé sur le
produit, signale à l’utilisateur des instructions d’utilisation ou de
maintenance importantes qui se trouvent dans la
documentation fournie avec le matériel.
Pour en savoir plus sur les règles de sécurité, la conformité à la
réglementation, la compatibilité EMI/EMF, l’accessibilité, et autres
sujets connexes, lisez les informations de sécurité et de conformité
Extron, réf. 68-290-01, sur le site Extron, www.extron.com.
Istruzioni di sicurezza • Italiano
AVVERTENZA: Il simbolo, D, se usato sul prodotto, serve ad avvertire
l’utente della presenza di tensione non isolata pericolosa all’interno
del contenitore del prodotto che può costituire un rischio di scosse
elettriche.
ATTENTZIONE: Il simbolo, I, se usato sul prodotto, serve ad avvertire
l’utente della presenza di importanti istruzioni di funzionamento e
manutenzione nella documentazione fornita con l’apparecchio.
Per informazioni su parametri di sicurezza, conformità alle normative,
compatibilità EMI/EMF, accessibilità e argomenti simili, fare riferimento
alla Guida alla conformità normativa e di sicurezza di Extron, cod. articolo
68‑290‑01, sul sito web di Extron, www.extron.com.
Instrukcje bezpieczeństwa • Polska
OSTRZEŻENIE: Ten symbol, D,gdy używany na produkt, ma na celu
poinformować użytkownika o obecności izolowanego i niebezpiecznego
napięcia wewnątrz obudowy produktu, który może stanowić zagrożenie
porażenia prądem elektrycznym.
UWAGI: Ten symbol, I, gdy używany na produkt, jest przeznaczony do
ostrzegania użytkownika ważne operacyjne oraz instrukcje konserwacji
(obsługi) w literaturze, wyposażone w sprzęt.
Informacji na temat wytycznych w sprawie bezpieczeństwa, regulacji wzajemnej
zgodności, zgodność EMI/EMF, dostępności i Tematy pokrewne, zobacz Extron
bezpieczeństwa i regulacyjnego zgodności przewodnik, część numer 68-290-01,
na stronie internetowej Extron, www.extron.com.
Инструкция по технике безопасности • Русский
ПРЕДУПРЕЖДЕНИЕ: Данный символ, D, если указан на
продукте, предупреждает пользователя о наличии
неизолированного опасного напряжения внутри корпуса
продукта, которое может привести к поражению электрическим током.
ВНИМАНИЕ: Данный символ, I, если указан на продукте,
предупреждает пользователя о наличии важных инструкций по
эксплуатации и обслуживанию в руководстве, прилагаемом к
данному оборудованию.
Для получения информации о правилах техники безопасности, соблюдении
нормативных требований, электромагнитной совместимости (ЭМП/ЭДС),
возможности доступа и других вопросах см. руководство по безопасности и
соблюдению нормативных требований Extron на сайте Extron:
www.extron.com, номер по каталогу - 68-290-01.
安全说明 • 简体中文
警告： D 产品上的这个标志意在警告用户该产品机壳内有暴露的危险 电压，
有触电危险。
注意：I 产品上的这个标 志意在 提示用 户设备 随附的用 户手
册中有重要的操作和维护(维修）说明。
关于我们产品的安全指南、遵循的规范、EMI/EMF 的兼容性、无障碍使用的特
性等相关内容，敬请访问 Extron 网站 www.extron.com，参见 Extron 安全规
范指南，产品编号 68-290-01。

安全記事 • 繁體中文
警告: D若產品上使用此符號，是為了提醒使用者，產品機殼內存在
著可能會導致觸電之風險的未絕緣危險電壓。
注意 I 若產品上使用此符號，是為了提醒使用者，設備隨附的用戶手冊
中有重要的操作和維護（維修）説明。
有關安全性指導方針、法規遵守、EMI/EMF 相容性、存取範圍和相關主題的
詳細資訊，請瀏覽 Extron 網站：www.extron.com，然後參閱《Extron 安
全性與法規遵守手冊》，準則編號 68-290-01。
安全上のご注意 • 日本語
안전 지침 • 한국어
경고: 이기호 D,가제품에 사용될 경우,제품의 인클로저 내에 있는
접지되지 않은 위험한 전류로 인해 사용자가 감전될 위험이
있음을 경고합니다.
주의: 이기호 I,가제품에 사용될 경우,장비와 함께 제공된 책자에
나와 있는 주요 운영 및유지보수(정비) 지침을 경고합니다.
안전 가이드라인, 규제 준수, EMI/EMF 호환성, 접근성, 그리고 관련 항목에
대한 자세한 내용은 Extron 웹사이트 (www.extron.com)의Extron 안전
및규제 준수 안내서, 68-290-01 조항을 참조하십시오.
警告: この記 号Dが製品上に表示されている場合は、筐体内に絶縁されていない高
電圧が流れ、感電の危険があることを示しています。
注意: この記号 Iが製品上に表示されている場合は、本機の取扱説明書に
記載されて いる重要な操作と保守(整備)の指示についてユーザーの
注意を喚起するものです。
安全上のご注意、法令遵守、EMI/EMF 適合性、その他の関連項目に
ついては、エクストロンのウェブサイト www.extron.com より
『Extron Safety and Regulatory Compliance Guide』(P/N 68-290-01) をご覧
ください。
Copyright
© 2016 Extron Electronics. All rights reserved.
Trademarks
All trademarks mentioned in this guide are the properties of their respective owners.
The following registered trademarks® , registered service marks(SM), and trademarks(TM) are the property of RGB Systems,
Inc. or Extron Electronics (see the current list of trademarks on the Terms of Use page at www.extron.com):
Registered Trademarks (®)
AVTrac, Cable Cubby, CrossPoint, DTP, eBUS, EDID Manager, EDID Minder, Extron, Flat Field, FlexOS, GlobalViewer, Global
Configurator, Hideaway, Inline, IP Intercom, IP Link, Key Minder, LinkLicense, LockIt, MediaLink, MediaPort, NetPA, PlenumVault,
PoleVault, PowerCage, PURE3, Quantum, SoundField, SpeedMount, SpeedSwitch, System INTEGRATOR, TeamWork, TouchLink,
V‑Lock, VersaTools, VN‑Matrix, VoiceLift, WallVault, WindoWall, XTP, and XTP Systems
Registered Service Mark(SM) : S3 Service Support Solutions
Trademarks (™)
AAP, AFL (Accu‑Rate Frame Lock), ADSP (Advanced Digital Sync Processing), Auto‑Image, CableCover, CDRS (Class D Ripple
Suppression), DDSP (Digital Display Sync Processing), DMI (Dynamic Motion Interpolation), Driver Configurator, DSP Configurator,
DSVP (Digital Sync Validation Processing), eLink, Entwine, EQIP, FastBite, FOX, FOXBOX, IP Intercom HelpDesk, MAAP, MicroDigital,
ProDSP, QS‑FPC (QuickSwitch Front Panel Controller), Room Agent, Scope‑Trigger, ShareLink, SIS, Simple Instruction Set, Skew‑Free,
SpeedNav, Triple‑Action Switching, True4K, Vector™ 4K, WebShare, XTRA, ZipCaddy, and ZipClip

FCC Class B Notice
Federal Communication Commission Interference Statement
This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This
equipment generates, uses and can radiate radio frequency energy and, if not installed and
used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one of the following measures:
•Reorient or relocate the receiving antenna.
•Increase the separation between the equipment and receiver.
•Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
•Consult the dealer or an experienced radio/TV technician for help.
FCC CAUTION: Any changes or modifications not expressly approved by the party
responsible for compliance could void the user’s authority to operate this equipment.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following
two conditions:
1. This device may not cause harmful interference, and
2. This device must accept any interference received, including interference that may
cause undesired operation.
This transmitter must not be co-located or operating in conjunction with any other antenna
or transmitter.
Operations in the 5.15-5.25GHz band are restricted to indoor usage only.
IMPORTANT NOTE:
FCC Radiation Exposure Statement:
This equipment complies with FCC radiation exposure limits set forth for an
uncontrolled environment. This equipment should be installed and operated with
minimum distance 25cm between the radiator & your body.
Industry Canada statement:
This device complies with RSS-247 of the Industry Canada Rules. Operation is subject to
the following two conditions: (1) This device may not cause harmful interference, and (2)
this device must accept any interference received, including interference that may cause
undesired operation.
Ce dispositif est conforme à la norme CNR-247 d’Industrie Canada applicable aux appareils radio
exempts de licence. Son fonctionnement est sujet aux deux conditions suivantes: (1) le dispositif
ne doit pas produire de brouillage préjudiciable, et (2) ce dispositif doit accepter tout brouillage
reçu, y compris un brouillage susceptible de provoquer un fonctionnement indésirable.

CAUTION: The device for operation in the band 5150-5250 MHz is only for indoor use to
reduce the potential for harmful interference to co-channel mobile satellite systems;
AVERTISSEMENT : Les dispositifs fonctionnant dans la bande 5150-5250 MHz sont
réservés uniquement pour une utilisation à l’intérieur afin de réduire les risques de
brouillage préjudiciable aux systèmes de satellites mobiles utilisant les mêmes canaux;
CAUTION: High-power radars are allocated as primary users (i.e. priority users) of
the bands 5250-5350 MHz and 5650-5850 MHz and that these radars could
cause interference and/or damage to LE-LAN devices.
AVERTISSEMENT : De plus, les utilisateurs devraient aussi être avisés que les utilisateurs
de radars de haute puissance sont désignés utilisateurs principaux (c.-à-d., qu’ils ont la
priorité) pour les bandes 5250-5350 MHz et 5650-5850 MHz et que ces radars
pourraient causer du brouillage et/ou des dommages aux dispositifs LAN-EL.
FOR MOBILE DEVICE USAGE
Radiation Exposure Statement:
This equipment complies with IC radiation exposure limits set forth for an uncontrolled
environment. This equipment should be installed and operated with minimum distance 22
cm between the radiator and your body.
Déclaration d’exposition aux radiations:
Cet équipement est conforme aux limites d’exposition aux rayonnements IC établies pour
un environnement non contrôlé. Cet équipement doit être installé et utilisé avec un
minimum de 22 cm de distance entre la source de rayonnement et votre corps.
NOTE: For more information on safety guidelines, regulatory compliances, EMI/EMF
compatibility, accessibility, and related topics, see the Extron Safety and
Regulatory Compliance Guide on the Extron website.
Battery Notice
This product contains a battery. Do not open the unit to replace the battery. If the battery
needs replacing, return the entire unit to Extron (for the correct address, see the Extron
Warranty section on the last page of this guide).
CAUTION: Risk of Explosion if Battery is replaced by an Incorrect Type. Dispose of
Used Batteries According to the Instructions.
ATTENTION : Risque d’explosion. Ne pas remplacer la pile par le mauvais type de
pile. Débarrassez-vous des piles utilisées selon le mode d’emploi.

Conventions Used in this Guide
Notifications
In this user guide, the following are used:
WARNING: Potential risk of severe injury or death.
AVERTISSEMENT : Risque potentiel de blessure grave ou de mort.
CAUTION: Risk of minor personal injury.
ATTENTION : Risque de blessure mineure.
ATTENTION:
•Risk of property damage.
•Risque de dommages matériels.
NOTE: A note draws attention to important information.
Software Commands
Commands are written in the fonts shown here:
^AR Merge Scene,,Op1 scene 1,1 ^B 51 ^W^C
[01]R000400300004000080000600[02]35[17][03]
E X!*X1&*X2)*X2#*X2! CE}
NOTE: For commands and examples of computer or device responses mentioned
in this guide, the character “0” is used for the number zero and “O” represents
the capital letter “o”.
Computer responses and directory paths that do not have variables are written in the font
shown here:
Reply from 208.132.180.48: bytes=32 times=2ms TTL=32
C:\Program Files\Extron
Variables are written in slanted form as shown here:
ping xxx.xxx.xxx.xxx —t
SOH R Data STX Command ETB ETX
Selectable items, such as menu names, menu options, buttons, tabs, and field names are
written in the font shown here:
From the File menu, select New.
Click the OK button.
Specifications Availability
Product specifications are available on the Extron website, www.extron.com.
Extron Glossary of Terms
A glossary of terms is available at www.extron.com/technology/glossary.aspx.

Contents
Introduction..................................................................1
About the WAP 100AC............................................1
Features....................................................................1
Application Diagram.................................................1
Installation Overview ...............................................2
Panel Features............................................................4
WAP 100AC Top Panel Features...........................4
WAP 100AC Bottom Panel Features......................8
Internal Web Pages...................................................9
Accessing the Internal Web Pages.........................9
Overview.................................................................10
Device Status 10
Connections 10
Network...................................................................11
Basic 11
Wireless 11
WPS 11
Management ..........................................................11
Advanced 11
Time Zone 11
Wi-Fi Scheduler 11
Tools 11
System Manager....................................................12
Account12
Firmware 12
Mounting..................................................................... 13
Before You Start.....................................................13
Mounting the WAP 100AC.....................................13
Mounting to a Solid Ceiling or Wall 14
Mounting to a Dropped Ceiling 15
Kensington Security Lock15
Reference Material..................................................16
Unit Reset...............................................................16
Updating Firmware.................................................16
Downloading Firmware to a PC 16
Uploading Firmware to the WAP 100AC 17
WAP 100AC • Contents vii

WAP 100AC • Contents viii

Introduction
This guide describes the function, installation, and operation of the Extron WAP 100AC
Wireless Access Point.
Unless otherwise stated, the terms “Wireless Access Point” or “WAP” refer to the WAP
100AC. The WAP 100AC provides wireless accessibility for the Extron TLP Pro 1022W.
This section provides an overview of these products:
•About the WAP 100AC
•Features
•Application Diagram
•Requirements
About the WAP 100AC
The WAP 100AC is a high-powered, long-range, dual-band concurrent wireless access
point. It is compliant with IEEE 802.11ac/a/b/g/n standards up to 300 Mbps at 2.4 GHz and
up to 867 Mbps at 5 GHz.
It is designed to operate in numerous environments, including multiple-floor offices and
other larger enterprise settings, where the high power and long range make it a cost-
effective alternative to ordainary access points.
Features
Features are from
EnGenius User Guide.
May need to update
when Marketing set up
a product page on the
Extron Proof site.
•Up to 26 dBm transmit power, enabling long range connectivity
•Supports IEEE802.11ac/a/b/g/n wireless standards with up to 300Mbps(2.4GHz)
and 867Mbps(5GHz)
•Four internal 5dBi Omni-Directional MIMO antennas
•Can be used with included power adapter or via PoE with PoE 802.3at - capable
Switches or Injectors
•Dual Band/Two Stream
•Band Steering shifts dual band clients to 5 GHz for better throughput performance
•Secured Guest Network
WAP 100AC • Introduction 1

Application Diagram
Figure 1 shows a typical application for the WAP 100AC.
Needs an Application Diagram from Marketing
Figure 1. WAP 100AC Application Diagram
WAP 100AC • Introduction 2

Installation
Overview
This section contains an overview of the installation process. Follow the links for a more
detailed explanation of each step.
1. Before starting, determine where to mount the WAP 100AC for optimal performance,
consider factors that can affect signal strength (see Before you Start in the Mounting
section on page 13).
2. Obtain the following network information from your network administrator:
Dynamic Host Configuration Protocol (DHCP) status (on or off). If DHCP is off, you
will also require:
IP address
Subnet mask
Gateway
User name —by default this is admin.
Passwords —by default this is extron.
MAC address —make a note of the touchpanel MAC address, which can be
found from the WAP 100AC internal Web page.
3. Mount and cable the units:
Mount the units (see Mounting on page 13).
NOTE: Prepare the mounting site but do not install the WAP 100AC until power
and network connections have been made.
ATTENTION:
•Do not power on the WAP 100AC until you have read the Attention notice
on page 6 (power injector) or on page 7 (12 VDC power supply).
•Ne branchez pas le WAP 100AC avant d’avoir lu les mises en garde
page 6 (injecteur PoE) ou page 7 (source d’alimentation 12 VCC).
Connect the network cable to the WAP 100AC. If you are using Power over
Ethernet (PoE), see LAN/PoE input on page 5.
Extron recommends using Power over Ethernet (PoE). If you are not using Power
over Ethernet, see 12V Power Input on page 7).
4. Configure the WAP 100AC for Network Communication:
Connect the PC that you are using for setup to the same Ethernet subnetwork as
the WAP 100AC.
Use the WAP 100AC internal Web pages to configure the unit (see page 9).
WAP 100AC • Installation Overview 3

Panel Features
This section describes:
•WAP 100AC Top Panel Features
•WAP 100AC Bottom Panel Features
WAP 100AC Top Panel Features
Figure 2 shows the top panel features of the WAP 100AC.
Figure2
A B
C D E
Figure 2. WAP 100AC Top Panel
A
B
C
D
E
LAN/PoE input
12 VDC Power input
Mounting holes (2)
Cable guide
Kensington security lock
WAP 100AC • Panel Features 4

LAN/PoE input A LAN/PoE input (see page 4)—accepts an input from a LAN or a power injector.
NOTE: The WAP 100AC can use a 12 VDC, minimum 1.0 A power supply or a
PoE+ (802.3at compliant) power injector. Extron recommends using PoE.
ATTENTION:
•Do not connect either power supply before reading the Attention notifications
on page 6 or page 7.
•Ne branchez pas de sources d’alimentation externes avant d’avoir lu les mises
en garde dans la section « Power Supply » sur page 6 ou page 7.
•If you are using a 12V Power Input (see page 11) , connect the WAP 100AC directly
to a network.
•To use a PoE power injector, connect the touchpanel as described below.
Extron recommends using a PoE+ (802.3at compliant) power injector.
•Limit the use to no more than two pass-through points, which may include patch
points, punch down connectors, couplers and power injectors. If these pass-through
points are required, use shielded couplers and punch-down connectors
NOTES: When using shielded twisted pair cable in bundles or conduits,
consider the following:
•Do not exceed 40% fill capacity in conduits.
•Do not comb the cable for the first 20 meters, where cables are
straightened, aligned, and secured in tight bundles.
•Loosely place cables and limit the used of tie wraps or hook-and-
loop fasteners.
•Keep twisted pair cables separate from AC power cables.
To use a PoE power injector —connect an Ethernet cable to the power supply and a
switch or router. This cable carries network information from the switch or router to the
power supply input. A second cable carries the network information and power from
the power supply to the touchpanel. Connect the IEC power cord to a convenient 100
VAC to 240 VAC, 50-60 Hz power source.
WAP 100AC • Panel Features 5

page 6
ATTENTION:
•The WAP 100AC is intended for connection to a Power over Ethernet circuit for
intra-building use only and are considered to be part of a Network Environment 0
per IEC TR62101.
•Le WAP 100AC est conçu pour une connexion à un circuit PoE pour une utilisation
intérieure seulement et est considéré comme faisant partie d’un environnement
réseau 0 par IEC TR62101.
•Always use a power supply provided by or specified by Extron. Use of an
unauthorized power supply voids all regulatory compliance certification and may
cause damage to the supply and the end product.
•Utilisez toujours une source d’alimentation fournie ou recommandée par Extron.
L’utilisation d’une source d’alimentation non autorisée annule toute conformité
réglementaire et peut endommager la source d’alimentation ainsi que le produit final.
•These products are intended for use with a UL Listed power source marked “Class 2” or
“LPS” and rated 12 VDC, minimum 1.0 A. or PoE+ (802.3at compliant) power injector.
•Ces produits sont destiné à une utilisation avec une source d’alimentation listée UL
avec l’appellation « Classe 2 » ou « LPS » et normée 12 Vcc, 1,0 A minimum ou
French Translation.
•Extron power supplies are certified to UL/CSA 60950-1 and are classified as LPS
(Limited Power Source). Use of a non-LPS or unlisted power supply will void all
regulatory compliance certification.
•Les sources d’alimentation Extron sont qualifiées UL/CSA 60950-1 et sont
classées LPS (Limited Power Source). L’utilisation d’une source d’alimentation non-
listée ou non-listée LPS annulera toute certification de conformité réglementaire.
•Unless otherwise stated, the AC/DC adapters are not suitable for use in air handling
spaces or in wall cavities. The power supply is to be located within the same vicinity
as the Extron AV processing equipment in an ordinary location, Pollution Degree 2,
secured to the equipment rack within the dedicated closet, podium, or desk.
•Sauf mention contraire, les adaptateurs AC/DC ne sont pas appropriés pour une
utilisation dans les espaces d’aération ou dans les cavités murales. La source
d’alimentation doit être située à proximité de l’équipement de traitement audiovisuel
dans un endroit ordinaire, avec un degré 2 de pollution, fixé à un équipement de
rack à l’intérieur d’un placard, d’une estrade, ou d’un bureau.
•Power over Ethernet (PoE) is intended for indoor use only. It is to be connected
only to networks or circuits that are not routed to the outside plant or building.
•L’alimentation via Ethernet (PoE) est destinée à une utilisation en intérieur
uniquement. Elle doit être connectée seulement à des réseaux ou des circuits qui ne
sont pas routés au réseau ou au bâtiment extérieur.
•The installation must always be in accordance with the applicable provisions of
National Electrical Code ANSI/NFPA 70, article 725 and the Canadian Electrical
Code part 1, section 16.
•Cette installation doit toujours être en accord avec les mesures qui s’applique au
National Electrical Code ANSI/NFPA 70, article 725, et au Canadian Electrical Code,
partie 1, section 16.
•The power supply shall not be permanently fixed to the building structure or
similar structure.
•La source d’alimentation ne devra pas être fixée de façon permanente à une structure
de bâtiment ou à une structure similaire.
WAP 100AC • Panel Features 6

12 VDC power
input
page 7
B 12 VDC power input (see page 4) —power supplies must be purchased separately.
Extron recommends using a PoE power injector. If you wish to use a power supply,
connect a 12 VDC, minimum 1.0 A power supply with a DC plug to the power input.
See www.extron.com for suitable models.
NOTES:
•The WAP 100AC ships without a power supply. Either a 12 VDC, minimum
1.0 A power supply or a PoE+ (802.3at compliant) power injector must be
purchased separately.
•Do not use both the 12 VDC power supply and power injector at the same time.
ATTENTION:
•Always use a power supply provided by or specified by Extron. Use of an
unauthorized power supply voids all regulatory compliance certification and
may cause damage to the supply and the end product.
•Utilisez toujours une source d’alimentation fournie ou recommandée par Extron.
L’utilisation d’une source d’alimentation non autorisée annule toute conformité
réglementaire et peut endommager la source d’alimentation ainsi que le produit final.
•These products are intended for use with a UL Listed power source marked
“Class 2” or “LPS” and rated 12 VDC, minimum 1.0 A. or PoE+ (802.3at
compliant) power injector.
•Ces produits sont destiné à une utilisation avec une source d’alimentation listée UL
avec l’appellation « Classe 2 » ou « LPS » et normée 12 Vcc, 1,0 A minimum ou
French Translation.
•Extron power supplies are certified to UL/CSA 60950-1 and are classified as
LPS (Limited Power Source). Use of a non-LPS or unlisted power supply will
void all regulatory compliance certification.
•Les sources d’alimentation Extron sont qualifiées UL/CSA 60950-1 et sont classées
LPS (Limited Power Source). L’utilisation d’une source d’alimentation non-listée ou
non-listée LPS annulera toute certification de conformité réglementaire.
•Unless otherwise stated, the AC/DC adapters are not suitable for use in air handling
spaces or in wall cavities. The power supply is to be located within the same vicinity
as the Extron AV processing equipment in an ordinary location, Pollution Degree 2,
secured to the equipment rack within the dedicated closet, podium, or desk.
•Sauf mention contraire, les adaptateurs AC/DC ne sont pas appropriés pour une
utilisation dans les espaces d’aération ou dans les cavités murales. La source
d’alimentation doit être située à proximité de l’équipement de traitement audiovisuel
dans un endroit ordinaire, avec un degré 2 de ption Ext4 fixé à un équipement de
rack à l’intérieur d’un placard, d’une estrade, ou d’un bureau.
•The installation must always be in accordance with the applicable provisions of
National Electrical Code ANSI/NFPA 70, article 725 and the Canadian Electrical
Code part 1, section 16.
•Cette installation doit toujours être en accord avec les mesures qui s’applique au
National Electrical Code ANSI/NFPA 70, article 725, et au Canadian Electrical
Code, partie 1, section 16.
•The power supply shall not be permanently fixed to the building structure or
similar structure.
•La source d’alimentation ne devra pas être fixée de façon permanente à une
structure de bâtiment ou à une structure similaire.
WAP 100AC • Panel Features 7

ATTENTION:
•The length of the exposed wires in the stripping process is critical. The ideal
length is 3/16 inches (5 mm). If they are any longer, the exposed wires may touch,
causing a short circuit between them. If they are any shorter, the wires can be
easily pulled out even if tightly fastened by the captive screws.
•La longueur des câbles exposés est primordiale lorsque l’on entreprend de les
dénuder. La longueur idéale est de 5 mm (3/16 inches). S’ils sont un peu plus longs,
les câbles exposés pourraient se toucher et provoquer un court circuit. S’ils sont un
peu plus courts, ils pourraient sortir, même s’ils sont attachés par les vis captives.
•Do not tin the wire leads before installing into the connector. Tinned wires are not
as secure in the connector and could be pulled out.
•Ne pas étamer les conducteurs avant de les insérer dans le connecteur. Les câbles
étamés ne sont pas aussi bien fixés dans le connecteur et pourraient être retirés.
Mounting holes
Cable guide
Kensington security
lock
C Mounting holes (2) (see page 4) —Used to mount the unit to a wall or ceiling (see Mounting on
page ).
D
E Kensington security lock —For added security, attach a Kensington Security Lock
(not provided) to the metal-reinforced slot on the top of the unit.
Follow the instructions that are provided by the manufacturer to install the lock.
WAP 100AC Bottom Panel Features
These features provide diagnostic tools that can be used for troubleshooting. The LEDs can
be activated or inactivated within the WAP 100AC web pages.
A
This needs a new Photo
from Marketing so that it
says “Extron.”
B CD E F
On page 9 of the EnGenius
user guide, it says this.
However, on page 58, the
software has a “Reset”
button that reboots the
device. I’m assuming that
these are different functions.
On page 51, the software has
another “Reset” button that
seems to have the same
function as the physical
reset button.
Figure 3. WAP 100AC Bottom Panel
A Reset button —resets all user settings and reverts back to the factory default state. To carry
out this reset, press the reset
button for over 10 seconds.
B
C WLAN 5G LED —indicates that the 5 GHz frequency is in use (IEEE
standard 802.11a, b, g, n,ac).
D WLAN 2.4G LED —indicates that the 2.4 GHz frequency is in
use (IEEE standard 802.11a, b, g, n,ac).
E Ethernet Port LED —indicates that the unit is connected to a network.
F Power LED —indicates that the unit is receiving power.
WAP 100AC • Panel Features 8
WPS LED —indicates Wi-Fi Protected Setup is enabled.
Cable guide —Ensures cables for power and network connections do not get damaged.

Internal Web
Pages
The WAP 100AC hosts internal Web pages that are used to configure the unit. This section
describes how to access the internal Web pages and a description of each page.
•Accessing the Internal Web Pages
•Overview
•Device Status
•Connections
•Network
•Basic
•
•
Wireless
WPS
•Management
•Advanced
•
•
•
Time Zone
WiFi Scheduler
Tools
•System Manager
•Account
•Firmware
Accessing the Internal Web Pages
EnGenius guide lists
IE/Firefox/Safari.
What about Edge and
Chrome?
To access the internal Web Pages:
1. Ensure the WAP 100AC is powered on and connected to a network.
2. Open a web browser on a PC connected to the same subnetwork as the WAP 100AC.
3. Enter the IP address of the WAP 100AC in the address bar. By default this is
192.168.1.10.
4. The Login dialog opens:
Figure 4. Login Dialog
By default the user name is admin and the user password is extron.
5. Click Login.
The Device Status page opens.
WAP 100AC • Internal Web Pages 9

Overview
Device Status
The Device Status page is read-only and shows general information about the WAP 100AC.
To view this information, click Device Status in the Overview section of the left side bar.
The information on this page is organized under Device Information (figure 5, 2) and
LAN Information (figure 6, 1).
Device Information
12
Figure 5. Device Status Page showing Device Information
•Device Name
•MAC Address —the WAP 100AC has separate MAC addresses for connecting to a
LAN, WLAN (2.4 GHz), and WLAN (5 GHz).
•Country —to configure the country or region, see Wireless Settings on page .
•Current Local Time —to configure date and time, see Date and Time Settings on page .
•Firmware Version —to update firmware, see Firmware Upgrade on page .
•Management VLAN ID —if your network includes VLANs, you can assign a
Management VLAN ID (see Management VLAN Settings on page).
WAP 100AC • Internal Web Pages 10

LAN Information
1
Figure 6. Device Status Page showing LAN Information
•Network settings (IP Address, Subnet Mask, Gateway, Primary DNS, Secondary DNS, and
DHCP Client). To configure these settings, see IP Network Settings on page .
•Spanning Tree Protocol (STP) status —see Spanning Tree Protocol (STP) Settings on page
13.
Connections
The WAP 100AC automatically keeps records (logs) of events in internal memory. To view
these logs, click Connections in the Overview section of the left side bar (1).
1
2
Figure 7. Connections Page
Click Refresh (2) to update the Connections Lists.
NOTES:
•If there is not enough memory to store all events, more recent events over-write
the oldest events.
•The log is cleared whenever the WAP 100AC is powered down or rebooted.
WAP 100AC • Internal Web Pages 11

Network
The Network section has three pages:
•Basic
•Wireless
•WPS
Basic
Configure the WAP 100AC IP settings from the Basic page. To access this page, click
Basic (1) in the Network section of the left side bar. This page allows you to configure:
•IP Settings (figure 9, 2)
•Spanning Tree Protocol (STP) Settings (figure 10, 1)
IP Settings
2
1
Figure 8. Network: Basic (IP Settings)
Before configuring these settings, obtain the relevant information from your
network administrator.
1. Choose DHCP or Static IP.
2. If you choose DHCP, all the addresses are obtained automatically when the WAP
100AC connects to a DHCP server.
If you choose Static IP, you must enter values for IP Address, Subnet Mask, Gateway,
Primary DNS, and Secondary DNS.
3. Click Save (figure 10, 2) to confirm the changes.
WAP 100AC • Internal Web Pages 12