Ovislink WL-8000AP User manual

-
802.11b/g Access Point
WL-8000AP
User’s Guide

-
FCC Certifications
This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This
equipment generates, uses and can radiate radio frequency energy and, if not installed and
used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the following measures:
!Reorient or relocate the receiving antenna.
!Increase the separation between the equipment and receiver.
!Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
!Consult the dealer or an experienced radio/TV technician for help.
CAUTION:
Any changes or modifications not expressly approved by the grantee of this device could void
the user’s authority to operate the equipment.
This device complies with Part 15 of the FCC rules. Operation is subject to the following two
conditions: (1) This device may not cause harmful interference, and (2) This device must
accept any interference received, including interference that may cause undesired operation.
FCC RF Radiation Exposure Statement
This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled
environment. This equipment should be installed and operated with a minimum distance of
20cm between the radiator and your body.
CE Mark Warning
This is a Class B product. In a domestic environment, this product may cause radio
interference, in which case the user may be required to take adequate measures.
All trademarks and brand names are the property of their respective proprietors.
Specifications are subject to change without prior notification.

-
Table of Content
Introduction ............................................................................................................................ 1
APPLICATION......................................................................................................................... 2
PARTS NAMES AND FUNCTIONS ............................................................................................ 3
FACTORY DEFAULT SETTINGS............................................................................................... 5
Setup ........................................................................................................................................ 6
Configuration.......................................................................................................................... 7
LOGIN.................................................................................................................................... 7
BASIC SETUP ......................................................................................................................... 8
ADVANCED SETUP................................................................................................................. 9
IP SETTING .......................................................................................................................... 11
PRIVACY.............................................................................................................................. 12
MANAGE ............................................................................................................................. 16
DOWNLOAD......................................................................................................................... 18
STATISTICS .......................................................................................................................... 19

1
INTRODUCTION
The Wireless 802.11b+g Access Point (AP) is an IEEE802.11g compliant access point.
It not only provides a high transfer rate up to 54Mbps, which is almost five times faster
than the already existing 11Mbps 802.11b products, but is also backward compatible with
the Wireless B equipments.
The AP provides 40/128/256 bit WEP encryption, WPA and IEEE802.1x, which ensures
a high level of security to protects users’ data and privacy. The MAC Address control
prevents the banned or unauthorized MAC Addresses from accessing your Wireless LAN.
Your network security is therefore double assured.
Placed anywhere along with an Ethernet LAN, the AP allows up to 200 wireless stations
within its area of coverage to access transparently to the corporate network.
The web-based configuration utility allows users to configure via web browser. Advanced
setup and firmware upgrade can be done easily.

2
Application

3
Parts Names and Functions
1. Top Panel: (LED Indicators)
LED Status
Indicator Color Solid Flashing
1 Power Green Turns solid green when
power is applied to this
device.
N/A.
2 ErrStatus Red Turns solid red when the
device is not working
properly.
When power on self-test
failure occurs.
3 Wireless
Link/Act.
Green Turns solid green when
connected and associated
to at least a client station.
Receiving/
Sending data
4LAN Green Turns solid green when
linked to a local network.
Receiving/
Sending data
Table 1: LED Indicators

4
2. Rear Panel: Connection Ports
Port/button Functions
A 9V DC Connects to the power adapter plug
B LAN Connects to Ethernet
C
(Factory)
RESET
Press for 5 seconds to reboot this device and restore factory
settings.
Performing the Factory Reset will erase all previously
entered device settings.
Table 2: Connection Ports

5
Factory Default Settings
Setting Wireless Access Point
Device Name Wireless AP
SSID Default value: ovislink
Channel 6
WEP Default value: Disabled
IP Address 192.168.1. 252

6
SETUP
Note: Before your starting hardware connection, you are advised to find an appropriate
location to place the Access Point. Usually, the best place for the Access Point is at the
center of your wireless network, with line of straight to all your wireless stations. Also,
remember to adjust the antenna; usually the antenna is placed higher, the performance
will be better.
1. Connect to your local area network:
Connect an Ethernet cable to the Ethernet port of this Wireless Access Point, and the
other end to a hub, switch, router, or another wireless access point.
2. Power on the device:
Connect the included AC power adapter to the Wireless Access Point’s power port
and the other end to a wall outlet.
Check the LEDs:
The Power, Wireless Link/Act. and LAN should be ON. Wireless Link/Act. and LAN
will blink if the data is being transmitted or received.
3. Configure your PC:
Make sure your local PC(s) has wireless network adapter installed.

7
CONFIGURATION
Login
1. Start your computer. Connect an Ethernet cable between your computer and the
Wireless Access Point.
2. Make sure your wired station is set to the same subnet as the Wireless Access Point,
i.e. 192.168.1.10
3. Start your WEB browser. In the Address box, enter the following:
HTTP://192.168.1.252
The configuration menu includes: Basic Setup, Advanced Setup, IP Setting,
Privacy, Manage, Download, and Statistics. The details for the configuration
menu are described as follows.

8
Basic Setup
The Setup page displays baci local and WLAN settings for the AP and enable you to
change the settings.
FW Version The current version of the firmware installed in this device.
SW Version The current version of the software installed in this device.
Wireless
Enable/Disable AP Enable/ Disable Click to enable/disable the AP.
Domain The AP’s domain determines the channel number.
MAC address/BSSID The AP’s MAC address/BSSID. BSSID displays the ID of
current BSS, which uniquely identifies each BSS. It is also the
MAC address of this Access Point.
SSID SSID is the unique name shared among all points in your
wireless network. It is case-sensitive and must not exceed 32
characters. It must be identical for all points in the network.
Make sure that all points in the network are the same.
Channel The number of channels supported depends on the region of
this Access Point. All stations communicating with the Access
Point must use the same channel.
Save After completing the settings, Click Save to save the settings.
Cancel Click Cancel to discard the data you have entered since last
time you press Save.

9
Advanced Setup
It is not recommended that settings in this page to be changed unless advanced users want
to change to meet their wireless environment for optimal performance.
Beacon Period Beacon Period is the amount of time between beacon
transmissions. Before a station enters power save mode, the
station needs the beacon period to know when to wake up to
receive the beacon (and learn whether there are buffered
frames at the access point). The default value is 200.
DTIM Period DTIM stands for Delivery Traffic Indication Message. A
DTIM is a countdown field informing clients of the next
window for listening to broadcast and multicast messages.
When the access point has buffered broadcast or multicast
message for associated clients, it sends the next DTIM with a
DTIM Period value. Access point clients hear and awaken to
receive the broadcast and multicast messages. The default
DTIM period is ‘2’.
RTS Threshold RTS (Request To Send) is a control frame sent from the
transmitting station to the receiving station requesting
p
ermission to transmit. This value is recommended to remain at
its default setting of 4096. Should you encounter inconsistent

10
data flow, only minor modifications of this value are
recommended.
Fragment Threshold Fragmentation mechanism is used for improving the
efficiency when high traffic flows along in the wireless
network. The value can be set from 256 to 4096. The default
value is 4096.
Output Power Level You can choose the percentage of maximum power to meet
your requirement. The default is Full.
b/g Mode You can choose one mode of the following you need.
"Mixed: 802.11b supported rate and 802.11g supported rate.
"b only: 802.11b supported rate only.
"b+: 802.11b supported rate and 22 Mbps PBCC rate.
"11g only: 802.11g supported rate only.
The default is Mixed mode.
Hidden SSID Support Click "Enabled or "Disabled to hide or broadcast the SSID.
TI Turbo Mode Click "Enabled or "Disabled to enable or disable enhancing
throughput rate.
Interference Avoidance Click "Enabled or "Disabled to enable or disable the Access
Point’s energy detection mechanism.
"Enabled/ "Disabled: enable or disable the vHCF feature.
Destination IP Address: The destination IP address with
preferred bandwidth.
Protocol: The destination AP’s protocol.
TI Video Blast Support
Port Number: The destination AP’s port number.
Save After completing the settings, Click Save to save the settings.
Defaults Click to restore the AP to factory default settings.
Cancel Click Cancel to discard the data you have entered since last
time you press Save.

11
IP Setting
The IP Settings page displays the IP address for the AP.
IP Address This field can be modified only when DHCP Client is disabled.
If your system manager assigned you static IP settings, then
you will have to enter the information provided.
Subnet Mask Enter the information provided by your system manager.
Default Gateway Enter the information provided by your system manager.
Save After completing the settings, Click Save to save the settings.
Cancel Click Cancel to discard the data you have entered since last
time you press Save.

12
Privacy
The Privacy page displays WLAN security settings. You can select WEP, 802.1x, or
WPA to be the privacy mode for the AP.
WEP
Privacy Turn privacy on and off when security is set to WEP. When
security is set to 802.1x or WPA, privacy is turned on
automatically.
Authentication Type Open: If the type is selected, the associated station should set
the same Authentication type as AP.
Shared: If the type is selected, there must be a key to be shared
between the AP and the associated station.
Both: Both Open and Shared are selected.
WEP Keys
Tx Key The selected key for transmission when WEP is selected.

13
Key Value Please set the Key Value according to the WEP Cipher you
select.
If 40bits is selected, 10 Hex characters are needed.
If 128bits is selected, 26 Hex characters are needed.
If 256bits is selected, 58 Hex characters are needed.
WEP Cipher You can choose one from "40bits"128bits"256bits. 256bits
is the highest WEP level among the three.
RADIUS
Not Required.
Save After completing the settings, Click Save to save the settings.
Cancel Click Cancel to discard the data you have entered since last
time you press Save.
802.1x
Group Key Interval Please enter the value to decide how long it should change the

14
Group Keys. The default is 3600 seconds.
WEP Keys
Not Required.
RADIUS
Server IP Address Enter the RADIUS Server’s IP Address provided by your ISP.
Port Enter the RADIUS Server’s port number provided by your ISP.
The default is 1812.
Secret Enter the secret phrase that the AP shares with the RADIUS
Server.
Save After completing the settings, Click Save to save the settings.
Cancel Click Cancel to discard the data you have entered since last
time you press Save.
WPA
802.1x WPA stations authenticate with RADIUS Server over 802.1x.
Enter a period of time in Group Key Interval field to decide
how long to change group keys.
PSK Hex WPA stations share the pre-shared key (PSK) with AP, you
have to enter 64 characters for the key. Enter a period of time

15
in Group Key Interval field to decide how long to change
group keys.
PSK String WPA stations share the pre-shared key (PSK) with AP, 8-63
characters are needed for the key. Enter a period of time in
Group Key Interval field to decide how long to change group
keys.
WEP Keys
Not Required.
RADIUS
Server IP Address Enter the RADIUS Server’s IP Address provided by your ISP.
Port Enter the RADIUS Server’s port number provided by your
ISP. The default is 1812.
Secret Enter the secret phrase shared between the AP and the
RADIUS Server.
Save After completing the settings, Click Save to save the settings.
Cancel Click Cancel to discard the data you have entered since last
time you press Save.

16
Manage
The management page displays information about stations that are currently associated
with the AP.
Refresh Click Refresh to update the Associated Station Table.
Associated Station Table
Mac Address The Mac address of the station associated with the AP.
State The current state between the associated station and the AP.
SSID The SSID for the associated station.
Active Rate The current data transmitting/receiving rate.
Ban STA (wireless Press the button to remove the Mac Address from the table if

17
station) Banned is selected in Allowed/Banned STA MAC Address.
Press the button to add the Mac Address in the table if Allowed
is selected in Allowed/Banned STA MAC Address.
If Allowed/Banned STA MAC Address is disabled, there will
be no effect when pressing the button.
Security Status The station ‘s security Status.
Allowed/Banned STA MAC Address
"Allowed "Banned
"Disable
"Allowed: only the stations shown in the table can associate
with the AP.
"Banned: the stations shown in the table can’t associate with
the AP.
"Disable: The table is disabled.
Add/Mac Address Enter a Mac address in Mac Address field and click Add to
add the address. Click Save on the bottom left corner to let the
change take effect.
Delete Allowed/Banned
Mac Address
Click Delete to remove the address from the Mac Address
field.
Multiple SSID Support
#The table can only be enabled when Privacy is set to WEP with Privacy off.
#When the table is enabled, you cannot change privacy settings.
#SSID strings can be added or removed at any time.
#Enabling or disabling the table requires an AP reboot.
"Enabled "Disabled Click to enable or disable Multiple SSID Support.
Add SSID Click Add to add the SSID entered in SSID field. The SSID
can be up to 32 characters. You have to click Save to make it
work.
Delete SSID Click Delete to remove added SSID(s) in the table.