EzwatchPro EZ-BULLET-PRO-VP User manual

DIGITAL VIDEO CAMERA
User's Manual
SKU# EZ-BULLET-PRO-VP
SKU# EZ-BULLET-PRO-VP
IR Camera - H gh Resolut on
36PCS 5mm IR LEDS
• Suggested mounting height 8'-12'
• Do not mount came a di ectly to a metal su face
• Do not mount came a di ectly to a metal su face
• Do not point came a di ectly into light sou ces
WARNING
Image Senso 1/3" SONY SUPR HAD CCD
Effective Pixels PAL:752(H)x582(V) NTSC:768(H)x494(V)
Attention items:
Attention:
To educe the dange of elect ic shock, please do not open the case (o back
cove ) of came a; eve ything needed fo use ope ation is on the su face of
the came a; please seek help f om a qualified p ofessional fo epai .
Effective Pixels PAL:752(H)x582(V) NTSC:768(H)x494(V)
Senso a ea 4.9mmx3.7mm
Signal system PAL/NTSC
Ho izontal esolution 550TVL
Minimum illumination 0Lux(IR LED ON)
Elect onic shutte Auto:1/50(1/60)-1/100,000Sec
S/N atio >48dB
Attention items:
• Do not touch CCD o lens
• Do not use any unidentified powe supply
• Avoid installation in unstable places
Tempe atu e: -20
⁰C/+50⁰C
S/N atio >48dB
Gamma 0.45
Lens 4-9mm Manual/Auto i is lens optional
Video output 1.0Vp-p, 75
Ω
IR wave length 850nm
Powe supply DV 12V±10%
Powe consumption less than 3.0W
• Do not use came a in the following conditions,
Tempe atu e: -20⁰C/+50⁰C
Powe consumption less than 3.0W
IR distance 35-40M

Making a BNC Connection
Connecting a P e-made Cable
Step 1: St ip away all of the cable and shielding so
you have 1/2" of the cente conducto exposed as
shown in the pictu e.
Connect this end to
the came a.
Step 2: Then st ip away the black oute jacket so
you have 1/4" of the shielding exposed. Do not
The cables a e labeled with a yellow w ap detailing the came a end
and the DVR end.
It s very mportant that you dent fy these ends
you have 1/4" of the shielding exposed. Do not
allow any of the coppe shielding to touch the
cente conducto .
Step 3: Inse t the cable into the fitting and gently
find the hole fo the cente conducto befo e you
and the DVR end.
It s very mportant that you dent fy these ends
before nstall ng the cable so that you have the correct ends at the
correct locat on.
find the hole fo the cente conducto befo e you
p ess the fitting onto the wi e. Now just twist the
fitting onto the wi e while fi mly p essing down
until the fitting is fi mly on the cable.
Installing a powe wi e pigtail
Contact
Step 1: At the came a location, take the powe
cable and st ip away the oute sheathing to
expose the inne two wi es (black & ed). Then
st ip away about 1/4" of the wi es jacket to
expose the coppe wi e. Do the same to the
powe wi e pigtail which connects to the came a
EZWATCHPRO
www.ezwatch-secu ity-came as.com
Phone/Fax
Technical Support/Sales
powe wi e pigtail which connects to the came a
powe connection as shown. Note: Do not st ip o
cut the powe lead coming di ectly f om the
came a. You should st ip the "pigtail" powe
cable which came with you kit. You should have
one "pigtail" fo each came a.
Technical Support/Sales
Toll F ee 1-866-241-3400
Inte national 001-801-4783980
Fax [phone]
Ma l
Step 2: Now take the ed powe cable lead and
twist it togethe with the black & white lead f om
the powe pigtail. Now take the black lead f om
the powe cable and twist it togethe with the all
black lead f om the pigtail. Use the g ay wi e nuts
p ovided with you system and twist them onto
Ma l
Main Office/Mailing Address
Automated Video Systems
1600 S. State St eet
Salt Lake City, UT 84115
p ovided with you system and twist them onto
the wi es until they a e fi mly secu ed.