EzwatchPro EZDOME-VP User manual

DIGITAL VIDEO CAMERA
User's Manual
SKU# EZDOME-VP
SKU# EZDOME-VP
Vandal-Proof ight Vision Camera w/ Wall Mount
• Suggested mounting height 8'-12'
• Do not mount camera directly to a metal surface
• Do not point camera directly into light sources
WAR I G
WAR I G
Attention: To
reduce the danger of electric shock please do not open the case (or back cover) of
camera; everything needed for user operation is on the surface of the camera;
Image Sensor 1/3" SONY EXVIEW HAD CCD
Effective Pixels PAL:500(H)x582(V) NTSC:510(H)x492(V)
Sensor area 4.9mmx3.7mm
Signal system PAL/NTSC Horizontal
resolution 420TVL Minimum
Attention items:
• Do not touch CCD or lens
• Please ensure correct voltage on power supply
• Avoid installation in unstable places
camera; everything needed for user operation is on the surface of the camera;
please seek help from a qualified professional for repair.
resolution 420TVL Minimum
illumination 0.0LUX Electronic shutter
Auto:1/50(1/60)-1/100 000Sec S/N ratio
>48dB Gamma 0.45
Lens 3.6mm Wide Angle
Video output 1.0Vp-p 75
Ω
Power supply DV 12V±10%
• Avoid installation in unstable places
Temperature: -20
⁰C/+50⁰C
Power supply DV 12V±10%
Power consumption 150mA Daytime 500mA Night
Operating Temperature -10⁰C-+50⁰C
• Do not use camera in the following conditions

Making a BNC Connection
Connecting a Pre-made Cable
Step 1: Strip away all of the cable and shielding so
you have 1/2" of the center conductor exposed as
shown in the picture.
Connect this end to
the camera.
Step 2: Then strip away the black outer jacket so
you have 1/4" of the shielding exposed. Do not
allow any of the copper shielding to touch the
center conductor.
Step 3: Insert the cable into the fitting and gently
The cables are labeled with a yellow wrap detailing the camera end and the
DVR end. It is very important that you identify these ends before installing
the cable so that you have the correct ends at the correct location.
Step 3: Insert the cable into the fitting and gently
find the hole for the center conductor before you
press the fitting onto the wire. Now just twist the
fitting onto the wire while firmly pressing down
until the fitting is firmly on the cable.
Installing a power wire pigtail
Contact
Step 1: At the camera location take the power
cable and strip away the outer sheathing to
expose the inner two wires (black & red). Then
strip away about 1/4" of the wires jacket to
EZWATCHPRO
www.ezwatch-
strip away about 1/4" of the wires jacket to
expose the copper wire. Do the same to the
power wire pigtail which connects to the camera
power connection as shown. Note: Do not strip or
cut the power lead coming directly from the
camera. You should strip the "pigtail" power
cable which came with your kit. You should have
one "pigtail" for each camera.
EZWATCHPRO
www.ezwatch-
security-cameras.com
Phone/Fax
Technical Support/Sales Toll
Free 1-866-241-3400
International 001-801-4783980 Fax
1-801-295-2191
Mail
cable which came with your kit. You should have
one "pigtail" for each camera.
Step 2: Now take the red power cable lead and
twist it together with the black & white lead from
the power pigtail. Now take the black lead from
the power cable and twist it together with the all
1-801-295-2191
Mail
Main Office/Mailing Address
Automated Video Systems
1600 S. State Street
Salt Lake City UT 84115
the power cable and twist it together with the all
black lead from the pigtail. Use the gray wire nuts
provided with your system and twist them onto
the wires until they are firmly secured.
Salt Lake City UT 84115