EZYmount SLT-400 User manual

SLT-400 manual.indd 2-3 10/08/12 1:29 PM
Installation Instructions
Flat Wall Mount
CAUTION: DO NOT EXCEED THE
MAXIMUM STATED WEIGHT CAPACITY.
SERIOUS INJURY OR PROPERTY
DAMAGE MAY OCCUR!
SLT-400 200x200 / 300x300
400x200 / 400x400
55″
MAX 70kg
Insert the safety bar to secure the rails.
A padlock can be used in the safety
bar to help prevent theft of your TV.
Note: the padlock is not included.
Maintenance
➔Check that the bracket is secure and safe to use at regular intervals
(at least every three months).
➔Please contact your local distributor if you have any questions.
70kg

➔Do not commence installation until you have read and understood the instructions
and warnings contained in this installationsheet. If you have any questions regarding
any of the instructions or warnings, please contact your place of purchase.
➔This mounting bracket was designed to be installed and utilised ONLY as
ed in this manual. Improper installation or use of this product may
cause damage or serious injury.
➔This product should only be installed by someone of good mechanical ability,
with basic building experience and full understanding of this manual.
➔Make sure that the supporting surface (i.e. wall) will safely support the combined
load of this bracket and all attached hardware (TV) and components.
➔If mounting to timber wall studs, make sure that the mounting screws are
nder is highly recommended.
➔Always use an assistant or mechanical lifting equipment to safely lift
and position equipment.
➔rmly, but do not over tighten. Over tightening can cause damage,
greatly reducing their holding power.
➔This product is intended for indoor use only. Using this product
outdoors could lead to product failure and personal injury.
WARNING
IMPORTANT: Ensure that you have received all parts according to the component checklist prior
to installation. If any parts are missing or faulty, contact your local distributor for assistance.
Wall plate (x1)
A
ST6.3x55 (x4)
W-A
Concrete anchor (x4)
W-B
D8 washer (x4)
W-C
Adapter bracket (x2)
B
Safety bar (x1)
C
NOTE: Please read the entire instruction manual before you start
installation and assembly
Component Checklist
SLT-400 manual.indd 2-3 10/08/12 1:29 PM

Find and mark the
exact location of
mounting holes.
Mark the exact
location of
mounting holes.
Drill pilot
holes.
Drill pilot
holes.
Screw the
wall plate
onto the
wall.
Screw the
wall plate
onto the
wall.
WARNING
WARNING
➔Make sure that mounting screws are anchored into the centre of the studs.
nder is highly recommended.
➔Installers are responsible to provide hardware for othertypes of mounting situations.
➔The installer must verify that the supporting surface will safely support the
combined load of the equipment and all attached hardware (TV) and components.
➔When installing wall mounts on cinder block, verify the actual concrete thickness
is at least 35mm for using the concrete anchors. Do not drill into mortar joints!
Be sure to mount in a solid part of the block, generally 25mm minimum from the
side of the block. It is suggested to use the electric drill on a slow setting to drill
the hole instead of a hammer drill to avoid breaking out the back of the hole when
entering a void or cavity.
➔The installer must verify that the supporting surface will safely support the
combined load of the equipment and all attached hardware (TV) and components.
kcolBetercnoCdnakcirBdiloSnognitnuoM:b1sllaWdutSrebmiTnognitnuoM.a1
SLT-400 manual.indd 4-5 10/08/12 1:29 PM

Top of TV
➔Position the adapter brackets as close as possible to the middle of the screen.
➔Screw the adapter brackets onto the TV.
Tighten all screws, but do not over tighten.
Make sure adapter brackets have been securely hooked onto the wall plate
before releasing the TV.
2. Attach Adapter Brackets
3. Hang TV on the Wall Plate
SLT-400 manual.indd 6-7 10/08/12 1:29 PM
M-A/M-B
M-F