F.I.T. PRO LED650 User manual

①
② Battery tube ③
Light Head
Tail Cap
Diving Backup Light
1
2 3
Spot Light (1pcs)
Battery clamp
Diving backup light
Brightness
650 lumen ( 1 * 18650 Li-ion )
④ O Ring 2pcs
Switch Button
Battery Level Indicator
350 lumen ( 3 *AAA )
Beam Angle
Run time
LED
Parameters
Over 50000 hours LED Life
Aviation aluminumMaterial
Hard anodic oxidationOxidation
Size
Weight 3 *AAA : 170 (in air), 70g (in water)
F.I.T. PRO LED650
Specifications
(LED Light)
(Lumen)
10 Degress
Battery 1 * 18650 Li-ion or 3 *AAA
approx.90 min + 10 min
Waterproof 100m / 330ft
1pcs XM-L2 U2
34 (D) x 133.3 (L) mm
-Component .............................................1
-Specifications .............................................2
-Unpacking .............................................3
-Battery Loading .............................................3
Contents
Component
Unpacking
Please read carefully before using the manual
-Operating Instructions ............................................ 4
-Temperature Protection .............................................5
-Battery Level Indicator ............................................ 5
-Automatic Overheat Protection ............................................ 5
-Charge the battery ............................................ 5
-Care and Maintenance ............................................ 6
-Warning ............................................ 6
-Standard Warranty ............................................ 7
-Troubles Solution ............................................ 7
<Instruction>
<How to use>
<Maintenance and Warranty>
(In water)
1 * 18650 Li-ion: 175g (in air), 80 (in water)
1. Anti-clockwise rotate to open the tail cap;
2. Loading 3*AAA batteries into the battery clamp and loading
3. Holding the light head and attach the tail cap by rotating
the battery into the tail cap.(Or loading 18650 Li-ion battery
Battery Loading
clockwise.
battery must match the polarity of the contacts.
Battery Clamp
⑤
Wrist lanyard
with the battery tube into the tail cap.) The polarity of the

45
6 7
Turn ON: Pressing the Switch Button for less than one second.
Warning
Do not open the tail cap when is diving；
Do not place or store the Video Light in extreme high or low
Standard Warranty
Entitled to after-sales warranty services of the flashlight,
if there are any quality issues and the buyer can free change
the comodity with vendors within 15 days. And it can free to
maintance any problems within One Year. But it will charge
the cost of part after more than One Year. Exclude the rules
as follow;
1.Be artificially modified, damaged, dismantling the flashlight
and parts;
2. Error operation led to failure to use the flashlight (Such as
anti-loaded or wrong loaded the battery , ect.);
3.Battery leakage is caused the failure of flashlight;
4.Force majeure factors are demagered the flashlight
(Forexample: Earthquakes,Flood disaster ect.)
Troubles Solution
1.Try to solve the symptoms as following indications.
2.If can’t solve please contact your local vender immediately.
Symptoms Solution
1、To check the battery whether
is
2、To check the battery whether
Unwork of LED 3、To check the tail cap whether
Indicator shows
installed backward.
has power .
has tightened.
green when it
begins charge
1、To check that it right installed
the positive and negative of battery
or the sharp-nel is contacted good
with charger;
2、To check the battery whether
is well inserted into charger;
Operating Instructions
Turn
O
N:(Start : 100% brightness)
When the inner temperature of flashlight is over the set
v alue, in order to keep the inner temperature in the control
r ange and the internal control circuit will automatic decrease
the brightness of LED.
Battery Level Indicator
Temperature Protection
Automatic Overheat Protection
When being used at a temperature higher than 55°C , the
light will automatically reduce the brightness by 50% to reduce
heat and protect the components.
Caution: When the battery level indicator is flash red.
1. Can’t switch the mode and adjust the brightness;
2.The brightness will be 20% output;
3. The light will automatic turn off 10 minutes later.
C
aution:
Care and Maintenance
1.Before you use the Diving Backup Light, read this manual
thoroughly to prevent accidental misuse, water intrusion or
damage.
2.The Backup Light be used underwater 100 meters (330ft).
3.The O Rings should be checked to ensure that they are free
from nay dirt, sand, hair and dust every time before closing
the Light head.
4.The O Rings should also be carefully checked for cracks or
blemishes. If cracks or blemishes occur, the O Ring should be
replaced immediately.
5. Gently and evenly apply a thin coat of grease to the entire
seal may help avoid abrasion and deterioration.
6. Remove the battery from the tail cap when finish traveling.
temperature.
Do not store the Video Light with battery installed to prevent
battery off gassing or leaking.
Do not place the Video Light near any flammable material to
initiating a fire.
Turn OFF: Pressing the Switch Button for two seconds.Turn
O
FF:
Adjustment brightness:Ad
j
ustment bri
g
htness:
(On-State) Pressing the Switch Button for less than one
second.
Turn On SOS:Turn
O
n
SOS:
Turn OFF SOS:
(OFF- State) Pressing the Switch Button for two seconds.
Turn
O
FF
SOS:
(SOS- State) Pressing the Switch Button for two seconds.
Switch mode: ( SOS / Flash explosion)
S
witch mode
:
(SOS- State) Pressing the Switch Button for less than one
second.
SOS Flash explosionFlash explosio
n
100% 50% 25%
5
0
%
25
%
When the battery level indicator low is flash red.
(OFF- State) Pressing the Switch Button for three seconds.
18650 Li-ion battery
AAA
(Green flash light)
(18650 Li-ion / 3*AAA)
(Red flash light)
18650 Li-ion batter
y
AAA
The diving light support AAA battery and 18650 Li-ion battery,
please select the battery type before using the light .
Activation Battery type selection:Activation Batter
y
t
y
pe selection
:
Battery type selection mode state: Pressing the Switch Button
for less than one second to switch the mode between 18650
Li-ion battery and AAA battery, pressing the Switch Button for
three seconds to save the selection.
Select battery type:
S
elect batter
y
t
y
pe: