F.I.T. LED PRO 5000 User manual



Content
I. Specification
II. Operation Instruction
Ⅰ. Specification
1.1 Construction



1.2 Specification
Brightness White: 5000Lumen; Red: 150Lumen
Light Beam White: 120degrees;Red:130degrees
Battery 11.1V/5200mAh Sanyo battery core lithium battery
Burn time White Led around1 hour up, Red LED 10 hours up

Depth Rating 100m/330ft
LED spec
White: CREE XM-L T6*9PCS, Color temperature:
5700K~6500K
Red: CREE XP-E R2*3PCS (Red, 620nm)
LED Life Over 50000 hours
Materials Aircraft degree aluminium+Hard anodized
Surface treatment Hard anodized
Size 75.5(D)*141(L)mm
Weight 561g(under water, battery included) 1190g(on land, battery )
Function
White light step-less adjustment, white / red status indicator,
Brightness level indicator, Battery status indicator, Low
battery warning, Low battery protection, Temperature
protection.
Special function
Air pressure safety release gate, Both sides of the battery are
the same (no electrode design)


1.3 Package




Ⅱ. Operation
2.I Assembly For Battery
2.1.1 Anticlockwise unscrew the rear cap of the video light.
2.1.2 Insert Lithium-ion battery pack into the light, both sides of the battery are the
same (no electrode design).
2.1.3 Clockwise turn the rear cap back to the light.
★ Notice: The rear must be turned back to the right place to avoid leaking.





2.2 Turn On / Off Video Light
2.2.1 Turn on: Press combine button, the light will be turned on (Full100% white is
the default).
2.2.2 Turn off: Under any turn on mode, press the combine button for 3 seconds
up, the light will be turned off.
2.2.3 Mode switching: Under the white mode and red mode, with a short press on
the combine button (3 seconds down), and it will be switched to another
mode by turns.
2.3 Fine Adjustment For Brightness Gear
Any brightness under white mode, switch the combine button anticlockwise,
the brightness will be lighter. Otherwise, switch the combine button clockwise, the
brightness will be darker.
2.4 Status Indicator
2.4.1 White Mode: The color of indicator is green.
2.4.2 Red Mode: The color of indicator is red.

2.5 Capacity Indicate
Capacity Status Indicator
>75% green
50%-75% yellow
20%-50% red
<20% flicking red
2.6 Brightness indicate
Brightness Indicate
71%-100% on on on
31%-70% on on off
10%-30% on off off
2.7 Charger Usage
2.7.1 When Lithium-ion battery pack need to be charged, please insert the DC
plug into the interface of the charger kit as following,
2.7.2 Then insert the AC plug into the power socket.
2.7.3 The indicator will turn green once the charge is completing.

2.8 Temperature Protection
If temperature reaches the setting value when you use the video light on land,
program will decrease the brightness to 20% automatically. And will recover to its
initial protected brightness automatically as soon as the temperature has been
decreased.
2.9 Low Capacity Protection
When the light with a low capacity, the brightness will decrease to 20%, and the
red indicator is flicking, then the light will be turned off automatically ten minutes
later.
2.10 Silicone Grease Usage.
If it is very hard to switch the rear cap, or the O-ring inside the rear cap is
dried-up after a long time use, please daub appropriate silicone grease.
2.11 O ring Replacement

When you find the o-ring inside the rear cap of the video light is broken or in
bad- shaped, please remove the defective one, then replace a new one. Please
daub appropriate silicone grease before replacing, any sharp tool is not allowed to
avoid damaging O ring.
2.12 Precautions
● Any other battery is not allowed.
● Screw the rear cap when you diving.
● Against above operation requirement is not allowed.
● Long time no use, please remove the battery.